LAN8710A-EZC-TR-ABC - 10/100 Ethernet PHY | Microchip
MPN: LAN8710A-EZC-TR-ABC ✓ AktifLAN8710A-EZC-TR-ABC Ringkasan
An Ethernet PHY is the physical-layer component that converts digital MAC data into differential signals for a twisted-pair cable, then converts received signals back into digital data. The LAN8710A occupies the PHY layer of the Ethernet hierarchy, above the physical medium and below the MAC layer. Its integrated 10/100 capability allows one Ethernet port design to support both legacy 10 Mbps networks and Fast Ethernet networks operating at 100 Mbps.
Microchip LAN8710A devices feature HP Auto-MDIX, which allows a single RJ45 port to work with straight-through or crossover cables. Automatic negotiation selects the best supported speed and duplex mode, while the transceiver also provides full-duplex operation for contemporary switched Ethernet links. These functions simplify installation and reduce the need for manual link configuration in consumer, industrial, and enterprise equipment.
The flexPWR technology used in the LAN8710A family supports low-power operation and is intended for compact, energy-conscious designs. The MII interface supports both 10 Mbps and 100 Mbps transfer rates, while RMII reduces the number of MAC interface signals where a reduced-pin architecture is desirable. The exposed thermal pad beneath the 5 mm by 5 mm package provides a direct heat-dissipation path to the PCB copper during continuous data transmission.
Typical uses include industrial Ethernet controllers, embedded Linux platforms, network appliances, set-top equipment, printers, IP cameras, and compact communication modules. A MAC such as a Microchip STM32 controller can connect over RMII when its integrated Ethernet MAC supports the required clock and data signaling, while a more complex processor may use the full MII interface.
For PCB design, reserve the exposed pad as a thermal and ground connection, follow the manufacturer's recommended magnetics and decoupling network, and keep the high-speed differential pairs short, symmetric, and continuously referenced to the ground plane. Confirm the exact pin functions, strap resistors, reference clock method, and RMII timing configuration in the LAN8710A datasheet before releasing the PCB layout.
Pilihan pengganti yang segera untuk LAN8710A-EZC-TR-ABC — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera LAN8710A-EZC-TR-ABC (sama faktor bentuk dan kaki) — berbeza dalam Package, MAC Interface, RoHS Status, Cable Support, Package Dimensions.
LAN8710A-EZC-TR
✅ Masuk Drop-In ⚠️ Spesifikasi Tidak DisahkanHubungi untuk harga
Lihat Datasheet →LAN8710A-EZC-ABC
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LAN8710AI-EZK-ABC
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LAN8710AI-EZK-TR
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LAN8710AI-EZK-TR-ABC
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →LAN8710A-EZC-TR-ABC Spesifikasi
| Ethernet Data Rates | 10 Mbps and 100 Mbps |
| Supported Standards | IEEE 802.3u |
| MAC Interface | MII and RMII |
| Operating Modes | 10BASE-T and 100BASE-TX, full-duplex |
| Supply Voltage Range | 1.6 V to 3.6 V |
| Number of Drivers/Receivers | 4/4 |
| Suhu Operasi | 0°C to 85°C |
| Package Type | 32-VFQFN with exposed pad |
| Package Dimensions | 5 mm x 5 mm x 0.9 mm |
| Jenis Pemasangan | Surface mount |
| Packaging | Tape and reel |
| Product Status | Active |
| Status RoHS | ROHS3 compliant |
| Auto-MDIX Support | HP Auto-MDIX |
| Link Negotiation | Automatic speed and duplex negotiation |
| Power Technology | Microchip flexPWR |
| Manufacturer Lead Time | 4 weeks |
Panduan Konfigurasi Pin LAN8710A-EZC-TR-ABC 5 mm x 5 mm x 0.9 mm
Konfigurasi pin untuk LAN8710A-EZC-TR-ABC (5 mm x 5 mm x 0.9 mm pakai). Penomeran pin, fungsi, dan garis bentuk koneksi ditakrifkan dalam dokumen pengeluar. Rujuk dokumen untuk kebentuk dan pedoman pengasman.
Tiada data garisan pin yang diperoleh untuk LAN8710A-EZC-TR-ABC.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
LAN8710A-EZC-TR-ABC patut untuk 6 aplikasis: Industrial Embedded Ethernet Controller, Compact Network Appliance, IP Camera and Security Equipment, ESP32-Based Connected Product, Printer and Networked Peripherals, Set-Top and Connected Consumer Equipment.
Industrial Embedded Ethernet Controller
The LAN8710A-EZC-TR-ABC fits industrial embedded controllers that need a compact 10/100 Ethernet endpoint with a short MAC-to-PHY interface. Its MII and RMII support allows the PCB to accommodate different MAC architectures, while 1.6 V to 3.6 V operation suits mixed 1.8 V, 2.5 V, and 3.3 V systems. The 5 mm by 5 mm VFQFN outline keeps the PHY area compact, and HP Auto-MDIX removes the need for a manually configured crossover link. In an industrial enclosure, provide thermal copper under the exposed pad and isolate the magnetics and cable connector from noisy power stages.
Disebarkan
Compact Network Appliance
A single LAN8710A-EZC-TR-ABC supports both 10BASE-T and 100BASE-TX links, making it suitable for compact gateways, controllers, and network appliances with legacy 10 Mbps fallback. Automatic negotiation selects the supported speed and duplex mode without user intervention, while HP Auto-MDIX allows either straight-through or crossover patch cables. The PHY occupies a 32-VFQFN footprint, reducing routing congestion around the transformer and RJ45 connector. Use the RMII interface when the controller supports it, and verify the reference-clock and strap requirements in the manufacturer datasheet.
Disebarkan
IP Camera and Security Equipment
The LAN8710A-EZC-TR-ABC can provide the copper-Ethernet physical layer in an IP camera or compact surveillance product while the system processor handles video and network protocol processing. Automatic negotiation preserves interoperability with both 10 Mbps and 100 Mbps switches, and HP Auto-MDIX improves installation reliability. The 5 mm by 5 mm package leaves more board space for the image sensor interface and storage. A controlled reference clock, clean PHY supply, and properly terminated magnetics are essential for reliable video streaming across temperature changes and cable lengths specified by IEEE 802.3u.
Disebarkan
ESP32-Based Connected Product
The LAN8710A-EZC-TR-ABC can add wired Ethernet to an ESP32-based product when the selected ESP32 variant exposes a compatible Ethernet MAC with RMII signaling. The PHY handles 10BASE-T and 100BASE-TX encoding, decoding, and auto-negotiation while the ESP32 manages the MAC and application protocol. The 1.6 V to 3.6 V PHY supply range supports common embedded rails, but the RMII signal levels, reference-clock source, and 50 MHz timing requirements must match the controller. Keep the RMII traces short and confirm the complete interface implementation against the LAN8710A datasheet.
Disebarkan
Printer and Networked Peripherals
The LAN8710A-EZC-TR-ABC suits network-enabled printers, scanners, and office peripherals that need a compact 10/100 port with broad switch compatibility. Supporting both 10 Mbps and 100 Mbps allows the same product to work on older networks while taking advantage of Fast Ethernet links where available. Automatic negotiation removes configuration complexity for users, and HP Auto-MDIX accepts either cable type. The exposed-pad VFQFN package supports dense board layouts, but the design must keep PHY supply noise away from sensitive signal paths and follow the manufacturer's recommended component placement around the transformer.
Disebarkan
Set-Top and Connected Consumer Equipment
The LAN8710A-EZC-TR-ABC provides a cost-conscious wired-network path for set-top boxes, media adapters, and connected consumer products that also use wireless links. Its small footprint and low-power flexPWR design suit space-constrained boards, while MII and RMII support gives designers flexibility in the choice of host controller. Automatic speed negotiation and HP Auto-MDIX improve end-user setup reliability. The component is specified for 0°C to 85°C, making it appropriate for indoor consumer products. For thermally variable environments, verify the complete system temperature budget and use an industrial-grade ordering option when required.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk LAN8710A-EZC-TR-ABC — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | LAN8710A-EZC-TR | LAN8710A-EZC-ABC | LAN8710AI-EZK-ABC | LAN8710AI-EZK-TR | LAN8710AI-EZK-TR-ABC |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-VFQFN (5x5) | 32-VFQFN (5x5) | 32-VFQFN (5x5) | 32-VFQFN (5x5) | 32-VFQFN (5x5) | 32-VFQFN (5x5) |
| Ethernet Data Rates | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps | 10 Mbps and 100 Mbps |
| Operating Temperature | 0°C to 85°C | -40°C to 85°C | 0°C to 85°C | -40°C to 85°C | -40°C to 85°C | -40°C to 85°C |
| Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX | HP Auto-MDIX |
| Delivery Format | Tape and reel | Tape and reel | Tray | Tray | Tape and reel | Tape and reel |
| Low-Power Technology | flexPWR | flexPWR | flexPWR | flexPWR | flexPWR | flexPWR |
Penyeberangsung Jelas
- Combines 10/100 support with both MII and RMII in one compact PHY (vsLAN8710AI-EZK-TR)
- Extensive compatibility with standard 10/100 network infrastructure (vsLAN8710A-EZC-TR)
- Tape-and-reel configuration supports automated production assembly (vsLAN8710A-EZC-ABC)
- Low-power design aligned with compact embedded systems (vsLAN8710AI-EZK-TR-ABC)
Catatan Desain
Place the PHY close to the RJ45 connector and integrated magnetics, and keep the differential pairs short, symmetric, and continuously referenced to an uninterrupted ground plane. Avoid placing the PHY clock source, switching regulators, and magnetic components directly beneath the network interface. Follow the pinout and layout guidance in the Microchip LAN8710A datasheet, including the treatment of the exposed pad and configuration straps.
Separate the PHY supply routing from noisy digital and switching-supply paths, and place the manufacturer-recommended bypass capacitors immediately beside the relevant power pins. The 1.6 V to 3.6 V operating range does not remove the need for local filtering: supply noise can affect clock jitter, RMII timing, and link stability. Validate the rail with an oscilloscope at the PHY pins under maximum traffic and during simultaneous MAC transmission.
The VFQFN exposed pad is the primary heat-dissipation path. Connect it to a solid ground plane with multiple vias and avoid thermally isolating the pad with narrow copper necks. For continuous 100 Mbps operation, check junction temperature against the lowest ambient temperature permitted by the completed product. Use the Microchip electrical data and package thermal information to determine whether additional copper area or a thermal via array is required.
Confirm the reference-clock source, reset behavior, strap-resistor values, and whether the host MAC requires RMII or MII before assigning the PCB pins. A clock-source or strap mismatch can prevent enumeration even when the PHY powers up correctly. Also confirm that the chosen alternative ordering code preserves the same pin configuration and temperature grade; package equality alone does not establish drop-in compatibility.
Maklumat Kesediaan
The Microchip product information identifies the LAN8710A-EZC-TR-ABC as ROHS3 compliant. The target is an active extended-commercial Ethernet PHY and is not identified as an automotive-qualified AEC-Q100 device.