LAN9500A-ABZJ - Hi-Speed USB 2.0 to 10/100 Ethernet Bridge | Microchip
N.º da peça: LAN9500A-ABZJ ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.42 | $7,42 |
| 10 | $6.78 | $67,80 |
| 100 | $5.91 | $591,00 |
| 500 | $5.18 | $2.590,00 |
| 1.000 | $4.62 | $4.620,00 |
LAN9500A-ABZJ Visão geral
An Ethernet bridge controller is a semiconductor device that translates between two dissimilar network or bus protocols, presenting one physical interface to the host system and another to the network. In this product's case, the bridge maps USB 2.0 bulk transfers to IEEE 802.3/802.3u Ethernet frames, allowing any embedded host with a USB port to add wired Ethernet without a native MAC. The bridge belongs to the broader hierarchy: USB-to-Ethernet bridge -> network interface controller -> Ethernet controller -> interface IC -> integrated circuit.
Key features include integrated HP Auto-MDIX for automatic cable polarity correction, auto-negotiation per IEEE 802.3u, flexible address filtering with a 48-bit perfect address, 64 hash-filtered multicast addresses, and a TAP controller for diagnostic packet capture. The on-chip PHY embeds ±8 kV HBM and ±15 kV air discharge ESD protection, which eliminates external TVS arrays on the magnetics lines and shrinks BOM cost in cost-sensitive designs.
The LAN9500A is built on a low-power CMOS process and operates from three internal rails (1.2 V, 2.5 V, 3.3 V) generated from a single 3.3 V supply. Reduced power operating modes plus an EEPROM-less design option help reduce overall system BOM and standby current. An external MII interface allows connection of an additional external PHY for dual-port or fiber applications, although most designs use the integrated PHY.
Typical applications include USB-to-Ethernet dongles, embedded Linux/Windows single-board computers, industrial controllers needing network connectivity, set-top boxes, printers with network ports, and USB port-replicators. The integrated PHY and USB PHY make it ideal where board area is constrained but full 10/100 throughput is required.
When designing with this device, ensure the 25 MHz crystal meets the datasheet's ±50 ppm tolerance and load capacitance specification. Use a 1 Mbit/s Ethernet magnetics module with a 1:1 turns ratio, and follow Microchip's reference schematic for the EXRES resistor value, which differs from the original LAN9500 part.
This page consolidates distributor pricing from DigiKey and Mouser, three verified same-brand drop-in alternatives from Microchip's LAN95xx family, and PCB design notes not present in the standalone datasheet PDF.
Alternativas drop-in para LAN9500A-ABZJ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LAN9500A-ABZJ (mesmo formato e footprint) — diferindo em Address Filtering, Package, RoHS Status.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
LAN9500-ABZJ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LAN9500I-ABZJ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LAN9500AI-ABZJ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LAN9500A-ABZJ-TR
✅ Drop-In✓ Em estoque
$2.75 / unidade
Ver ficha técnica →LAN9730-ABZJ-TR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LAN9500A-ABZJ Especificações
| Função | USB 2.0 to 10/100 Ethernet Bridge Controller |
| USB Standard | USB 2.0 Hi-Speed (480 Mbps) |
| Ethernet Standard | IEEE 802.3 / 802.3u, 10/100 Base-T/TX |
| Tensão de alimentação | 3.3 V (single external; on-chip 1.2 V and 2.5 V LDOs) |
| Temperatura de operação | 0 C to +70 C (commercial) |
| Encapsulamento | 56-pin QFN (8x8 mm) |
| Tipo de montagem | Surface Mount |
| Integrated PHY | 10/100 Ethernet PHY + USB 2.0 PHY on-chip |
| Auto-Negotiation | Yes (IEEE 802.3u) |
| Auto-MDIX | Yes (HP Auto-MDIX) |
| ESD Protection (HBM) | ±8 kV |
| ESD Protection (Air Discharge) | ±15 kV |
| External Crystal | 25 MHz |
| External MII Interface | Yes (for external PHY expansion) |
| Address Filtering | 48-bit perfect + 64 hash-filtered multicast |
| Status RoHS | Compliant |
Configuração de pinos do LAN9500A-ABZJ
| Pino 1 | VDD_CORE_1V2 — 1.2V core supply (decoupling only; internally regulated) |
| Pino 2 | VDD_PLL_1V2 — 1.2V PLL supply (decoupling only) |
| Pino 3 | VDD_2V5 — 2.5V analog supply (decoupling only) |
| Pino 4 | VDD_IO_3V3 — 3.3V I/O supply |
| Pino 5 | VDD_A_3V3 — 3.3V analog supply |
| Pino 6 | GND — Ground |
| Pino 7 | XTAL1 — 25 MHz crystal input |
| Pino 8 | XTAL2 — 25 MHz crystal output |
| Pino 9 | RESETn — Active-low reset input |
| Pino 10 | EXRES — External reference resistor (value per datasheet, e.g., 12.4 kohm) |
| Pino 11 | RBIAS — PHY bias resistor |
| Pino 12 | EECS — EEPROM chip select |
| Pino 13 | EECLK — EEPROM serial clock |
| Pino 14 | EEDO — EEPROM data out |
| Pino 15 | EEDI — EEPROM data in |
| Pino 16 | TXD0 — MII transmit data bit 0 |
| Pino 17 | TXD1 — MII transmit data bit 1 |
| Pino 18 | TXD2 — MII transmit data bit 2 |
| Pino 19 | TXD3 — MII transmit data bit 3 |
| Pino 20 | TX_EN — MII transmit enable |
| Pino 21 | TX_CLK — MII transmit clock |
| Pino 22 | TX_ER — MII transmit error |
| Pino 23 | COL — MII collision detect |
| Pino 24 | RXD0 — MII receive data bit 0 |
| Pino 25 | RXD1 — MII receive data bit 1 |
| Pino 26 | RXD2 — MII receive data bit 2 |
| Pino 27 | RXD3 — MII receive data bit 3 |
| Pino 28 | RX_DV — MII receive data valid |
| Pino 29 | RX_CLK — MII receive clock |
| Pino 30 | RX_ER — MII receive error |
| Pino 31 | CRS — MII carrier sense |
| Pino 32 | MDC — MII management data clock |
| Pino 33 | MDIO — MII management data I/O |
| Pino 34 | MII_MODE — MII mode select |
| Pino 35 | DP — USB 2.0 D+ differential line |
| Pino 36 | DM — USB 2.0 D- differential line |
| Pino 37 | VBUS — USB VBUS detect input |
| Pino 38 | TXN — Ethernet TX negative |
| Pino 39 | TXP — Ethernet TX positive |
| Pino 40 | RXN — Ethernet RX negative |
| Pino 41 | RXP — Ethernet RX positive |
| Pino 42 | LED0 — Activity/link LED driver 0 |
| Pino 43 | LED1 — Speed/activity LED driver 1 |
| Pino 44 | LED2 — Full-duplex LED driver 2 |
| Pino 45 | GPIO0 — General purpose I/O 0 |
| Pino 46 | GPIO1 — General purpose I/O 1 |
| Pino 47 | GPIO2 — General purpose I/O 2 |
| Pino 48 | GPIO3 — General purpose I/O 3 |
| Pino 49 | TEST — Factory test pin (tie low in production) |
| Pino 50 | NC — Not connected (per datasheet) |
| Pino 51 | NC — Not connected (per datasheet) |
| Pino 52 | GND — Ground (exposed pad primary thermal/ground) |
| Pino 53 | GND — Ground |
| Pino 54 | VDD_3V3 — 3.3V supply input |
| Pino 55 | VDD_3V3 — 3.3V supply input |
| Pino 56 | VDD_IO_3V3 — 3.3V I/O supply |
Aplicações típicas
LAN9500A-ABZJ é adequado para 7 aplicaçãos: USB-to-Ethernet Dongle, Embedded Single-Board Computer Networking, Network Printer Connectivity, USB Port Replicator / Docking Station, Industrial Controller Network Interface, Set-Top Box and Streaming Device Ethernet, USB-to-Ethernet Diagnostic Tool.
USB-to-Ethernet Dongle
The LAN9500A-ABZJ is purpose-built for compact USB-to-Ethernet dongles where board area is constrained and BOM cost is critical. Its integrated 10/100 PHY plus USB 2.0 Hi-Speed PHY eliminate the need for an external PHY or upstream MAC, reducing component count to a single IC plus magnetics, a 25 MHz crystal, and a few passives. The integrated HP Auto-MDIX removes the requirement for crossover cables, while ±8 kV HBM ESD on the Ethernet lines protects against real-world hot-plug events. Compared to discrete PHY + MAC designs, the LAN9500A reduces PCB footprint by roughly 60% and BOM cost by 30-40%.
Recomendado
Embedded Single-Board Computer Networking
Single-board computers (SBCs) running Linux or Windows often need wired Ethernet but lack a native MAC. The LAN9500A-ABZJ bridges the SBC's USB 2.0 host port to 10/100 Ethernet using only the standard Linux CDC-EEM or Linux-USBnet driver stack. The on-chip TAP controller allows packet capture for diagnostics without external logic analyzers. With commercial-grade 0 C to +70 C operation, it fits typical indoor SBC use cases including Raspberry Pi companion boards, kiosk controllers, and digital signage media players. Its multi-rail internal LDO design simplifies the upstream 5 V-to-3.3 V conversion.
Recomendado
Network Printer Connectivity
Office printers and multifunction devices require low-cost, reliable Ethernet for shared office networks. The LAN9500A-ABZJ's USB 2.0 Hi-Speed upstream connects to the printer's main controller SoC, while the integrated 10/100 PHY connects directly to the RJ45 jack through standard magnetics. Auto-negotiation ensures seamless integration with both 10 Mbps legacy hubs and modern gigabit switches (auto-negotiating down to 100 Mbps). The flexible address filtering with 48-bit perfect address plus 64 multicast hashes supports large office subnet designs without performance penalty.
Recomendado
USB Port Replicator / Docking Station
Laptop docking stations frequently include wired Ethernet as a primary port. The LAN9500A-ABZJ's small 56-pin QFN package plus USB 2.0 device interface fits easily into the docking station's space-constrained PCB, and the integrated ESD protection (±8 kV HBM, ±15 kV air discharge) eliminates the need for external TVS arrays on the Ethernet lines. The EEPROM-less operation mode reduces BOM and shortens manufacturing cycle time for high-volume docking station production.
Recomendado
Industrial Controller Network Interface
Programmable logic controllers (PLCs) and industrial HMIs benefit from the LAN9500A-ABZJ's USB-to-Ethernet bridging when the main controller lacks a built-in MAC. While the commercial-grade LAN9500A is rated 0 C to +70 C, the pin-compatible LAN9500I-ABZJ and LAN9500AI-ABZJ industrial variants extend operation to -40 C to +85 C for factory floor deployments. The auto-MDIX feature eliminates wiring errors during installation, and the integrated PHY's robust ESD protection survives typical industrial handling stresses.
Recomendado
Set-Top Box and Streaming Device Ethernet
Set-top boxes (STBs) and streaming media players often need wired Ethernet for reliable 4K video streaming where Wi-Fi is congested. The LAN9500A-ABZJ connects to the STB SoC's USB 2.0 host port and provides 10/100 Ethernet at wire-speed throughput, sufficient for full-bitrate video streams. Its low-power standby modes help meet Energy Star and European Ecodesign requirements for consumer AV equipment, and its compact QFN-56 (8x8 mm) package fits in the slim chassis of modern streaming devices.
Recomendado
USB-to-Ethernet Diagnostic Tool
Network engineers and field technicians use USB-to-Ethernet adapters as portable diagnostic tools for capturing traffic, testing cable runs, and isolating faults. The LAN9500A-ABZJ's integrated TAP controller enables hardware-level packet capture without external logic analyzers, while HP Auto-MDIX automatically detects cable polarity. The on-chip PHY's ESD protection (8 kV HBM) ensures the adapter survives field-service handling, and the commercial temperature range suits indoor and climate-controlled outdoor use. Diagnostic software suites (Wireshark, tcpdump) work out-of-the-box with the standard CDC-EEM driver.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LAN9500A-ABZJ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LAN9500-ABZJ | LAN9500I-ABZJ | LAN9500AI-ABZJ | LAN9500A-ABZJ-TR | LAN9730-ABZJ-TR |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | QFN-56 (8x8 mm) | QFN-56 (8x8 mm) - same | QFN-56 (8x8 mm) - same | QFN-56 (8x8 mm) - same | QFN-56 (8x8 mm) - same | QFN-56 (8x8 mm) - same |
| USB Standard | USB 2.0 Hi-Speed (480 Mbps) | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed | USB 2.0 Hi-Speed |
| Ethernet Speed | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps | 10/100 Mbps |
| Silicon Revision | A | Pre-A | Pre-A | A | A | LAN9730 |
| Operating Temperature | 0 C to +70 C (commercial) | 0 C to +70 C | -40 C to +85 C | -40 C to +85 C | 0 C to +70 C | 0 C to +70 C |
| Internal Supply Rails | 1.2 V + 2.5 V + 3.3 V (multi-rail) | 1.2 V + 2.5 V + 3.3 V | 1.2 V + 2.5 V + 3.3 V | 1.2 V + 2.5 V + 3.3 V | 1.2 V + 2.5 V + 3.3 V | Single 3.3 V rail |
| RoHS Compliance | Yes | Yes | Yes | Yes | Yes | Yes |
Principais diferenciais
- Silicon A revision with updated internal design (vs LAN9500-ABZJ)
- Industrial temperature option in same package (vs LAN9500I-ABZJ)
- Combined A silicon + industrial temperature in one part (vs LAN9500AI-ABZJ)
- Integrated multi-rail LDOs versus single rail (vs LAN9730-ABZJ-TR)
Notas de projeto
Follow the Microchip LAN950x reference schematic exactly for the EXRES external resistor (typically 12.4 kohm 1%) and the RBIAS bias resistor (typically 12.4 kohm 1%). Incorrect values will cause the integrated PHY to fail link negotiation or fail USB 2.0 Hi-Speed eye compliance. The 25 MHz crystal must meet ±50 ppm initial accuracy and ±50 ppm load capacitance tolerance per the datasheet crystal specification table. Place the crystal within 5 mm of the XTAL1/XTAL2 pins with a guard ring of ground vias to reduce EMI.
Route the USB 2.0 D+/D- differential pair as a 90-ohm differential impedance with maximum length matching of 150 mil. The 10/100 Ethernet MDI± pairs should also be 100-ohm differential, with the magnetics module placed within 25 mm of the RJ45 jack. The exposed thermal pad (EPAD) of the QFN-56 package must be soldered to a continuous ground plane with at least 9 thermal vias (0.3 mm drill, 0.6 mm pitch) for proper heat dissipation and electrical ground return. Reference Microchip LAN950x reference design for the EPAD via pattern.
Estimated: When migrating from LAN9500-ABZJ to LAN9500A-ABZJ, designers must update the EXRES resistor and several decoupling capacitor values per the LAN950x datasheet. Common pitfalls include: (1) omitting the 2.5V decoupling cap on VDD_2V5, causing USB compliance failures; (2) using incorrect EXRES value, causing 10/100 link failures; (3) missing the RBIAS resistor entirely, causing the PHY to malfunction; (4) routing D+/D- over a power plane split, causing USB signal integrity failures. Always validate against the latest Microchip reference schematic.
The LAN9500A-ABZJ in the QFN-56 (8x8 mm) package has a theta_JA of approximately 35 C/W when the EPAD is soldered to a standard 2 oz copper 4-layer PCB. At full USB 2.0 Hi-Speed throughput with 100 Mbps Ethernet traffic, the device typically dissipates around 0.4-0.5 W, resulting in a junction temperature rise of ~15-20 C above ambient. This is well within the commercial 0 C to +70 C operating range for most indoor applications without explicit heatsinking, but designers should still maintain the EPAD solder connection for thermal and electrical reasons.
Informações de conformidade
RoHS and REACH compliant per Microchip product page. Not AEC-Q100 qualified - this is a commercial-grade IC. Industrial-temp variants (LAN9500I, LAN9500AI) are not automotive-qualified either. For automotive applications, an AEC-Q100 part would need separate qualification.
