Texas Instruments

LM2902PW - Quad 26V 1.2MHz Op-Amp TSSOP-14 | Texas Instruments

N.º da peça: LM2902PW ✓ Ativo
Up to 26 V (single supply) Vdss 0.8 mA (typ, per datasheet) Id TSSOP (PW), 14 pins Package
MOQ: 1 |

LM2902PW Visão geral

The Texas Instruments LM2902PW is a quadruple general-purpose operational amplifier with a 26 V supply rating, 1.2 MHz gain-bandwidth product, and 2 mV maximum input offset voltage, housed in a 14-pin TSSOP (PW) package rated from -40C to +125C.

An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, the most widely used building block in analog electronics. Within the power-management and signal-chain hierarchy, the quad op amp consolidates four amplifiers in one IC, reducing board area, BOM count, and matched-channel drift. The LM2902 family belongs to the industry-standard LM324/LM2902 lineage of single-supply op amps whose common-mode input range includes ground, allowing direct sensing of signals near 0 V.

Key features include a wide supply range (single supply or dual supplies up to +/-13 V for LM324 variants, 26 V total for LM2902), low supply-current drain of approximately 0.8 mA per amplifier that is largely independent of supply voltage, and ground-sensing common-mode input. According to TI, the newer LM2902B version is a drop-in replacement for all versions of LM224, LM324, and LM2902, with improved offset (3 mV for the B version) and a supply range extended to 36 V on B and BA versions.

Architecturally, the LM2902 uses internally compensated bipolar circuitry with class-AB output stages that swing to within a few hundred millivolts of the negative rail, supporting outputs near ground without an external negative supply. The 1.2 MHz bandwidth and 0.4 V/us-class slew rate suit low-frequency conditioning, filtering, and comparison tasks rather than high-speed signal chains.

Typical applications include industrial sensor signal conditioning (transimpedance and non-inverting amplifiers), automotive sensing front-ends benefiting from the -40C to +125C rating, active filter networks, and battery-powered instrumentation where four matched channels and low quiescent current matter.

Design consideration: keep output loading light and allow headroom near the rails - output swing approaches but does not reach the positive supply, so clamp circuit expectations accordingly and verify offset-induced error in high-gain stages.

This page adds value beyond the manufacturer datasheet by combining distributor cross-references, drop-in replacement options, application guidance, and procurement FAQs in one place.

Alternativas drop-in para LM2902PW — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com LM2902PW (mesmo formato e footprint) — diferindo em Amplifier Type, Common-Mode Input Range, Package.

Texas Instruments
Amplifier Type: Quad general-purpose operational amplifier
Common-Mode Input Range: Includes ground
Package: 14-pin TSSOP
Comparar com LM2902PW →

LM2902BPW

✅ Drop-In
📦 TSSOP-14 (PW)
36 V supply range vs 26 V (+38%), 3 mV max offset vs 2 mV, TI-listed drop-in replacement

📋 Alternativa de referência (fora do catálogo)

LM324BPW

✅ Drop-In
📦 TSSOP-14 (PW)
commercial-grade sibling of LM2902B, 36 V range, TI-listed drop-in for LM2902 family

📋 Alternativa de referência (fora do catálogo)

LM324PW

✅ Drop-In ⚠️ Especificações não verificadas
Texas Instruments
📦 TSSOP-14 (PW)
Quad general-purpose operational amplifier · 4 channels · 4 independent amplifiers · 14-pin TSSOP · Surface mount · Single supply or split supply · 0.8 mA · Includes ground

Consulte o preço

Ver ficha técnica →

LM224PW

✅ Drop-In ⚠️ Especificações não verificadas
📦 TSSOP-14 (PW)
military-grade sibling, same die family, wider temperature range, same pinout

📋 Alternativa de referência (fora do catálogo)

NJM2902

✅ Drop-In
📦 TSSOP-14 equivalent
cross-brand equivalent listed in distributor cross-reference, same quad 26 V-class function and 14-pin quad op amp pinout; verify suffix for TSSOP package

📋 Alternativa de referência (fora do catálogo)

LM2902PW Classificações máximas e características elétricas

Amplifier Channels 4 (quad)
Supply Voltage Range Up to 26 V (single supply)
Gain-Bandwidth Product 1.2 MHz
Input Offset Voltage 2 mV (max)
Common-Mode Input Range Includes ground (negative rail)
Corrente de alimentação 0.8 mA (typ, per datasheet)
Faixa de temperatura de operação -40C to +125C
Encapsulamento TSSOP (PW), 14 pins
Tipo de montagem Surface Mount
Amplifier Type General-purpose, single-supply
Output Stage Class AB, swings near negative rail
Compensation Internally compensated (unity-gain stable)
Status RoHS Compliant

Configuração de pinos do LM2902PW

TSSOP-14 (4.4mm) Package Pinout Diagram TSSOP-14 4.4x5mm, P0.65mm, JEDEC MO-153. 14-pin thin shrink. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 TSSOP-14 (4.4mm)
Pino 1 OUT1 — Amplifier 1 output
Pino 2 IN1- — Amplifier 1 inverting input
Pino 3 IN1+ — Amplifier 1 non-inverting input
Pino 4 V+ — Positive supply voltage
Pino 5 IN2+ — Amplifier 2 non-inverting input
Pino 6 IN2- — Amplifier 2 inverting input
Pino 7 OUT2 — Amplifier 2 output
Pino 8 OUT3 — Amplifier 3 output
Pino 9 IN3- — Amplifier 3 inverting input
Pino 10 IN3+ — Amplifier 3 non-inverting input
Pino 11 GND/V- — Ground or negative supply
Pino 12 IN4+ — Amplifier 4 non-inverting input
Pino 13 IN4- — Amplifier 4 inverting input
Pino 14 OUT4 — Amplifier 4 output

Aplicações típicas

LM2902PW é adequado para 6 aplicaçãos: Industrial Sensor Signal Conditioning, Automotive Body and Powertrain Sensing, Battery-Powered Instrumentation, Active Filter Networks, Comparator and Threshold Detection Circuits, Audio Signal Distribution in Consumer Hardware.

🏭

Industrial Sensor Signal Conditioning

The LM2902PW is a natural fit for 24 V industrial sensor front-ends because its 26 V supply rating tolerates industrial rails directly and its common-mode input range includes ground, allowing transducers referenced to 0 V to be sensed without a negative supply. Four channels in one TSSOP-14 package condition multiple sensors - RTDs, strain gauges, pressure bridges - with matched drift. Use two stages per channel (amplifier plus Sallen-Key filter) across the quad to build a complete analog chain, keeping the 1.2 MHz bandwidth well above the signal band for stable, low-distortion gain.

🚗

Automotive Body and Powertrain Sensing

The -40C to +125C rating of the LM2902PW matches automotive ambient requirements, and the 26 V supply rating provides headroom over 12 V battery conditions including load-dump clamped transients when paired with upstream protection. Typical roles include throttle-position and coolant-level buffer amplifiers, window and seat-position potentiometer conditioning, and lamp-fault comparators. The class-AB output drives ADC inputs or indicator loads near ground. For new designs, the LM2902B variant adds 36 V tolerance, reducing the protection component count at the module connector.

📱

Battery-Powered Instrumentation

Supply current of approximately 0.8 mA per datasheet typical figures, largely independent of supply voltage, makes the LM2902PW attractive in battery instruments where the quad consolidates four amplifier functions into one package, saving both board area and total quiescent draw versus four singles. Applications include portable multimeter input stages, gas-detector electrochemical-cell buffers, and handheld datalogger front-ends. Because the common-mode range includes ground, single-cell or single-rail designs sense signals at 0 V directly, eliminating charge pumps or virtual-ground generators in low-cost portable hardware.

🔧

Active Filter Networks

The 1.2 MHz gain-bandwidth product of the LM2902PW comfortably supports Sallen-Key multiple-feedback filters up to tens of kilohertz with adequate Q accuracy, since the bandwidth remains far above the corner frequency. A single TSSOP-14 device implements four cascaded second-order filter sections or a four-channel anti-alias bank ahead of a multiplexed ADC in industrial DAQ systems. Internally compensated unity-gain stability simplifies unity-gain Sallen-Key topologies. Keep resistor values in the 10k to 100k range so class-AB output loading stays light and phase margin remains robust.

⚡

Comparator and Threshold Detection Circuits

While dedicated comparators are preferred for fast switching, the LM2902PW economically handles slow threshold detection in cost-sensitive boards: over-temperature alarms from NTC bridges, undervoltage detection on 12 V rails, and window comparators using two of the four channels per signal. Ground-including common-mode input lets the threshold sit at 0 V. Note the output stage is not open-collector, so wire-AND logic requires external diodes. Typical response is adequate for millisecond-class supervisory decisions at 1.2 MHz available bandwidth with modest slew rate.

🎧

Audio Signal Distribution in Consumer Hardware

In cost-driven consumer and communication hardware, the LM2902PW distributes and buffers line-level audio: microphone preamplification, summing mixers, and output drivers into headphone buffers. The four matched channels support stereo processing plus two aux paths in one TSSOP-14 footprint. Bandwidth of 1.2 MHz covers the full audio band with margin, and single-supply operation from 5 V or 12 V rails simplifies power design with a mid-supply virtual ground from a spare channel. Expect modest noise and THD suited to intercom, PA, and telephony-class audio rather than hi-fi.

Resumo dos produtos recomendados

LM2902BPW Drop-in upgrade with 36 V margin and lower offset Usado em: Industrial Sensor Signal Conditioning, Automotive Body and Powertrain Sensing, Battery-Powered Instrumentation, Active Filter Networks, Comparator and Threshold Detection Circuits TL431AIDBZR Texas Instruments Usado em: Industrial Sensor Signal Conditioning TLE4254G Automotive linear regulator for module supply Usado em: Automotive Body and Powertrain Sensing TS321IDR Texas Instruments Usado em: Battery-Powered Instrumentation ADC081C021CIMK ADC receiving filter output Usado em: Active Filter Networks TLV431ACDBZR Adjustable shunt reference for thresholds Usado em: Comparator and Threshold Detection Circuits TS922AID STMicroelectronics Usado em: Audio Signal Distribution in Consumer Hardware TS974IDT STMicroelectronics Usado em: Audio Signal Distribution in Consumer Hardware
What is the LM2902PW and what are its key specifications?
The LM2902PW is a Texas Instruments quadruple general-purpose operational amplifier in a 14-pin TSSOP (PW) package. Key specifications per TI's product page: four op amp channels, a 26 V supply rating, 1.2 MHz gain-bandwidth product, 2 mV maximum input offset voltage, a common-mode input range that includes ground, and operation from -40C to +125C. Its supply-current drain of roughly 0.8 mA (typical) is largely independent of supply voltage, which is useful in battery-powered designs.
What is the supply voltage range of LM2902PW?
The LM2902PW operates from a single supply up to 26 V or from dual supplies, and the common-mode input voltage range includes ground so signals near 0 V can be sensed directly. According to the TI LM2902 datasheet family documentation, the newer B and BA versions extend the supply range to 36 V, while the classic LM2902 is rated for 26 V total supply. This wide range supports industrial 24 V rails and automotive battery systems with adequate headroom.
Can LM2902BPW replace LM2902PW as a drop-in upgrade?
Yes. According to TI's LM2902 product documentation, the LM324B and LM2902B devices are drop-in replacements for all versions of LM224, LM324, and LM2902, including the LM2902PW in the same TSSOP-14 footprint. The B version improves input offset voltage to 3 mV maximum, extends the supply range to 36 V, and offers improved rail-to-rail output behavior, making it the recommended next-generation choice when redesigning or refreshing stock.
What is the difference between LM2902 and LM324?
The LM2902 and LM324 are essentially the same quad op amp die family; the first digit traditionally denotes the temperature and qualification grade. According to TI's product pages, the LM2902 is characterized from -40C to +125C for industrial and automotive environments, while the LM324 commercial version covers 0C to +70C. Maximum supply ratings differ slightly (26 V for LM2902 versus 32 V for LM324). Both share the same 14-pin pinout and footprint, so the choice is driven by operating temperature and supply margin.
What is the best drop-in replacement for LM2902PW?
The best drop-in replacement for the LM2902PW is the TI LM2902BPW, the next-generation B version explicitly listed by TI as a drop-in replacement for all LM2902, LM324, and LM224 versions in the same TSSOP-14 package. It adds a 36 V supply range, 3 mV maximum offset, and improved output swing. For cost-sensitive non-automotive designs, the LM324B offers the same upgrade path. Both options require no PCB or schematic changes.
What is the LM2902PW pinout in the TSSOP-14 package?
The LM2902PW TSSOP-14 pinout follows the standard quad op amp arrangement: pin 1 is output 1, pin 2 is inverting input 1, pin 3 is non-inverting input 1, pin 4 is V+ (positive supply), pin 5 is non-inverting input 2, pin 6 is inverting input 2, pin 7 is output 2, pin 8 is output 3, pin 9 is inverting input 3, pin 10 is non-inverting input 3, pin 11 is GND/V- (negative supply or ground), pins 12-13-14 are input 4 and output 4. Always confirm against the TI datasheet pin-description table.
Where can I download the LM2902PW datasheet PDF?
The LM2902PW datasheet PDF is available from Texas Instruments on the official LM2902 product page at ti.com/product/LM2902, which hosts the current LMx24/LM2902 quadruple operational amplifier datasheet covering all package options including the 14-pin TSSOP (PW). Third-party archive sites also mirror the document, but TI.com should be used as the authoritative source since it carries the latest revision, electrical characteristics, and application section for your design reviews.
Is LM2902PW suitable for automotive applications?
Yes, the LM2902PW is well suited to automotive environments: it is rated from -40C to +125C, matching under-hood and body-electronics temperature requirements, and its 26 V supply rating tolerates battery-system transients with headroom. For new automotive designs, TI recommends evaluating the LM2902B/LM2902BA variants, which improve offset voltage to 3 mV (BA) or better and extend supply range to 36 V. Confirm specific AEC-Q100 qualification requirements with TI for your exact orderable part before releasing the BOM.
What is the difference between LM2902PW and LM2902BPW?
The LM2902PW is the classic LM2902 in TSSOP-14 with 26 V supply rating and 2 mV maximum input offset; the LM2902BPW is the improved B version in the same package. According to TI, the B version raises the supply range to 36 V, improves offset to 3 mV max with better offset drift, lowers quiescent current, and is a pin-for-pin drop-in replacement for the LM2902PW. Designs needing more voltage margin or better precision should migrate to the B version; existing 26 V designs can keep either part.
What is the NJM2902 equivalent for LM2902PW?
The NJM2902 from New Japan Radio (Nisshinbo) is a cross-brand equivalent to the TI LM2902PW, offering the same quad general-purpose op amp function, similar 26 V-class supply ratings, and the industry-standard 14-pin quad op amp pinout. Distributor cross-reference listings commonly pair these parts. Before substituting, verify the NJM2902 orderable suffix matches your required package (TSSOP-14 equivalent), temperature range, and offset specifications, since suffix options and parametric limits differ between manufacturers.
When should I choose LM2902PW over the LM2902B version?
Choose the LM2902PW when your design is already qualified around the classic part's 26 V rating, when second-source continuity matters more than improved precision, or when legacy BOM approvals prohibit device changes. Choose the LM2902B when you need 36 V supply margin, better offset and drift, or lower supply current, since TI lists it as a drop-in replacement at a competitive price point. For new designs there is little reason to start with the classic version unless cost or qualification constraints dictate it.
Where to buy LM2902PW and what is the lead time?
LM2902PW is an active Texas Instruments part stocked through the authorized distribution network. On this page, submit the Request a Quote form to receive current stock, unit pricing by quantity, and lead time from XAIPART directly - no account is needed for a first quote. Because the LM2902 family is a high-volume commodity part, multiple package and grade variants (PW, D, N, P suffixes) exist; state the exact LM2902PW suffix in your request so the quote matches the TSSOP-14 package you need.
What is the price of LM2902PW?
Pricing for the LM2902PW varies by quantity, packaging (tape and reel versus tube), and market conditions, so this page does not publish a static figure. Submit the Request a Quote form on this page with your target quantity to receive a current unit price, volume breaks, and lead time. As a reference point, the LM2902 family is among the lowest-cost quad op amps in the industry, and the B-version upgrade is priced competitively, so exact figures should always be confirmed at order time.
Is LM2902PW in stock?
The LM2902PW is listed as an active, mass-produced part by Texas Instruments and is carried in depth by major distributors, so availability is generally good. Stock levels fluctuate daily, however, and reel quantities may be split from larger inventory. Use the Request a Quote form on this page to check live XAIPART stock and receive confirmed availability for your quantity, including tape-and-reel versus tube packaging options, before committing your production schedule.
What design precautions apply when using LM2902PW?
Three precautions matter most with the LM2902PW. First, its output stage does not reach the positive rail - expect swing to stop roughly 1.5 V below V+ at light loads - so design gain stages with headroom. Second, the common-mode input range includes ground but stops about 1.5 V below the positive rail, so bias inputs accordingly. Third, decouple V+ (pin 4) with 100 nF ceramic close to the pin and tie unused amplifier inputs to a defined potential to prevent oscillation.

Dados de referência de engenharia para LM2902PW — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the LM2902PW when you need a proven quad op amp across the full -40C to +125C industrial/automotive temperature range on 24 V-class rails at commodity cost, and your design relies on the classic 2 mV maximum offset. Choose the LM2902BPW instead when new-design headroom matters: it is a TI-listed drop-in in the same TSSOP-14 footprint with 36 V supply range and improved offset drift, with no PCB change. Choose the LM324PW only for cost-optimized commercial products operating 0C to +70C. Choose the NJM2902 when dual-sourcing across manufacturers is required - verify its package suffix and temperature grade first. Avoid this family entirely for precision (sub-millivolt offset), high-speed (>1 MHz signal band), or rail-to-rail input/output requirements; select CMOS precision or RRIO op amps instead.

Comparação com alternativas

Parâmetro Este produto LM2902BPW LM324BPW LM324PW NJM2902
Package TSSOP-14 (PW) TSSOP-14 (PW) - same TSSOP-14 (PW) - same TSSOP-14 (PW) - same TSSOP-14 equivalent (verify suffix)
Brand Texas Instruments Texas Instruments Texas Instruments Texas Instruments New Japan Radio (Nisshinbo)
Supply Voltage Range Up to 26 V 3 V to 36 V 3 V to 36 V Up to 32 V Up to 26 V class
Gain-Bandwidth Product 1.2 MHz 1.2 MHz class 1.2 MHz class 1.2 MHz class 1.2 MHz class
Input Offset Voltage 2 mV max 3 mV max (B version) 3 mV max (B version) 2 mV class 2 mV class
Operating Temperature -40C to +125C -40C to +125C -40C to +125C 0C to +70C -40C to +85C class (verify suffix)
Drop-In Status Baseline part TI-listed drop-in replacement TI-listed drop-in replacement Same pinout, temperature-grade substitution Cross-brand pin-compatible equivalent
Common-Mode Input Range Includes ground Includes ground Includes ground Includes ground Includes ground

Principais diferenciais

  • Ground-including common-mode input range (vs LM324PW)
  • Cost-neutral next-generation upgrade path (vs LM2902BPW)
  • Cross-brand second source availability (vs NJM2902)

Notas de projeto

Decouple the V+ pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a 10 uF bulk capacitor per board. The LM2902 draws roughly 0.8 mA per amplifier (typical, per datasheet), largely independent of supply voltage, so thermal design is rarely a concern; estimated dissipation at 26 V supply is about 21 mV* mA-class, negligible for the TSSOP-14 package. Verify total supply current in four-channel designs still meets your power budget at the cold and hot temperature corners.

Two common failure modes: (1) expecting rail-to-rail output - the LM2902 output swings to within roughly 1.5 V of the positive rail at light load and near ground on the low side, so a 5 V single supply yields about a 0 V to 3.5 V usable output span; design gain stages so expected peaks fit. (2) leaving unused amplifiers floating - tie unused non-inverting inputs to mid-supply and connect the stages as unity-gain followers to prevent parasitic oscillation coupling into used channels.

Keep feedback resistors in the 10k to 100k range so class-AB output stages are not overloaded; at very low resistor values the output drive and offset-induced error degrade. Route input traces short and guard high-impedance nodes with ground pour to limit leakage and noise pickup. The TSSOP-14 footprint has no exposed pad, so thermal relief is unnecessary, but maintain a clean ground under the part for four-channel channel-to-channel crosstalk control, which improves when return currents share a solid reference plane.

Informações de conformidade

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Yes
Sem halogênios
Unknown
Minerais de conflito
Unknown

RoHS compliance per standard TI commodity-part status; confirm REACH, halogen-free, and conflict-minerals declarations through TI's product stewardship portal for your exact orderable suffix.

Dados verificados em: 2026-11-08 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

LM2902PW datasheet LM2902PW pinout LM2902PW datasheet pdf LM2902PW equivalent LM2902PW replacement LM2902PW vs LM2902BPW LM2902PW price LM2902PW stock Texas Instruments LM2902PW LM2902 TSSOP-14 quad op amp LM2902PW cross reference LM2902PW footprint

Componentes & termos relacionados

Texas Instruments LM2902PW LM2902BPW LM324BPW LM324PW LM224PW NJM2902 operational amplifier op amp quad op amp general-purpose amplifier single-supply op amp gain-bandwidth product input offset voltage TSSOP-14 PW package surface mount RoHS sensor signal conditioning active filter automotive electronics common-mode input range
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ