LM2902PW - Quad 26V 1.2MHz Op-Amp TSSOP-14 | Texas Instruments
MPN: LM2902PW ✓ 啟用中LM2902PW 概覽
An operational amplifier (op amp) is a high-gain voltage amplifier with differential inputs and a single-ended output, the most widely used building block in analog electronics. Within the power-management and signal-chain hierarchy, the quad op amp consolidates four amplifiers in one IC, reducing board area, BOM count, and matched-channel drift. The LM2902 family belongs to the industry-standard LM324/LM2902 lineage of single-supply op amps whose common-mode input range includes ground, allowing direct sensing of signals near 0 V.
Key features include a wide supply range (single supply or dual supplies up to +/-13 V for LM324 variants, 26 V total for LM2902), low supply-current drain of approximately 0.8 mA per amplifier that is largely independent of supply voltage, and ground-sensing common-mode input. According to TI, the newer LM2902B version is a drop-in replacement for all versions of LM224, LM324, and LM2902, with improved offset (3 mV for the B version) and a supply range extended to 36 V on B and BA versions.
Architecturally, the LM2902 uses internally compensated bipolar circuitry with class-AB output stages that swing to within a few hundred millivolts of the negative rail, supporting outputs near ground without an external negative supply. The 1.2 MHz bandwidth and 0.4 V/us-class slew rate suit low-frequency conditioning, filtering, and comparison tasks rather than high-speed signal chains.
Typical applications include industrial sensor signal conditioning (transimpedance and non-inverting amplifiers), automotive sensing front-ends benefiting from the -40C to +125C rating, active filter networks, and battery-powered instrumentation where four matched channels and low quiescent current matter.
Design consideration: keep output loading light and allow headroom near the rails - output swing approaches but does not reach the positive supply, so clamp circuit expectations accordingly and verify offset-induced error in high-gain stages.
This page adds value beyond the manufacturer datasheet by combining distributor cross-references, drop-in replacement options, application guidance, and procurement FAQs in one place.
直接替換替代品,適用於 LM2902PW — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
此系列的變體
與下列產品可直接替換的同系列型號: LM2902PW (相同外形與佔位) — 差異在於 Amplifier Type, Common-Mode Input Range, Package.
LM2902BPW
✅ 直接替換📋 參考替代品(不在目錄中)
LM324BPW
✅ 直接替換📋 參考替代品(不在目錄中)
LM324PW
✅ 直接替換 ⚠️ 規格未經驗證聯絡詢價
查看資料表 →LM224PW
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
NJM2902
✅ 直接替換📋 參考替代品(不在目錄中)
LM2902PW 最大額定值與電氣特性
| Amplifier Channels | 4 (quad) |
| Supply Voltage Range | Up to 26 V (single supply) |
| Gain-Bandwidth Product | 1.2 MHz |
| Input Offset Voltage | 2 mV (max) |
| Common-Mode Input Range | Includes ground (negative rail) |
| 供應電流 | 0.8 mA (typ, per datasheet) |
| 工作溫度範圍 | -40C to +125C |
| 封裝 | TSSOP (PW), 14 pins |
| 安裝類型 | Surface Mount |
| Amplifier Type | General-purpose, single-supply |
| Output Stage | Class AB, swings near negative rail |
| Compensation | Internally compensated (unity-gain stable) |
| RoHS 狀態 | Compliant |
LM2902PW 腳位配置
| 腳位 1 | OUT1 — Amplifier 1 output |
| 腳位 2 | IN1- — Amplifier 1 inverting input |
| 腳位 3 | IN1+ — Amplifier 1 non-inverting input |
| 腳位 4 | V+ — Positive supply voltage |
| 腳位 5 | IN2+ — Amplifier 2 non-inverting input |
| 腳位 6 | IN2- — Amplifier 2 inverting input |
| 腳位 7 | OUT2 — Amplifier 2 output |
| 腳位 8 | OUT3 — Amplifier 3 output |
| 腳位 9 | IN3- — Amplifier 3 inverting input |
| 腳位 10 | IN3+ — Amplifier 3 non-inverting input |
| 腳位 11 | GND/V- — Ground or negative supply |
| 腳位 12 | IN4+ — Amplifier 4 non-inverting input |
| 腳位 13 | IN4- — Amplifier 4 inverting input |
| 腳位 14 | OUT4 — Amplifier 4 output |
典型應用
LM2902PW 適用於 6 應用s: Industrial Sensor Signal Conditioning, Automotive Body and Powertrain Sensing, Battery-Powered Instrumentation, Active Filter Networks, Comparator and Threshold Detection Circuits, Audio Signal Distribution in Consumer Hardware.
Industrial Sensor Signal Conditioning
The LM2902PW is a natural fit for 24 V industrial sensor front-ends because its 26 V supply rating tolerates industrial rails directly and its common-mode input range includes ground, allowing transducers referenced to 0 V to be sensed without a negative supply. Four channels in one TSSOP-14 package condition multiple sensors - RTDs, strain gauges, pressure bridges - with matched drift. Use two stages per channel (amplifier plus Sallen-Key filter) across the quad to build a complete analog chain, keeping the 1.2 MHz bandwidth well above the signal band for stable, low-distortion gain.
推薦
Automotive Body and Powertrain Sensing
The -40C to +125C rating of the LM2902PW matches automotive ambient requirements, and the 26 V supply rating provides headroom over 12 V battery conditions including load-dump clamped transients when paired with upstream protection. Typical roles include throttle-position and coolant-level buffer amplifiers, window and seat-position potentiometer conditioning, and lamp-fault comparators. The class-AB output drives ADC inputs or indicator loads near ground. For new designs, the LM2902B variant adds 36 V tolerance, reducing the protection component count at the module connector.
推薦
Battery-Powered Instrumentation
Supply current of approximately 0.8 mA per datasheet typical figures, largely independent of supply voltage, makes the LM2902PW attractive in battery instruments where the quad consolidates four amplifier functions into one package, saving both board area and total quiescent draw versus four singles. Applications include portable multimeter input stages, gas-detector electrochemical-cell buffers, and handheld datalogger front-ends. Because the common-mode range includes ground, single-cell or single-rail designs sense signals at 0 V directly, eliminating charge pumps or virtual-ground generators in low-cost portable hardware.
推薦
Active Filter Networks
The 1.2 MHz gain-bandwidth product of the LM2902PW comfortably supports Sallen-Key multiple-feedback filters up to tens of kilohertz with adequate Q accuracy, since the bandwidth remains far above the corner frequency. A single TSSOP-14 device implements four cascaded second-order filter sections or a four-channel anti-alias bank ahead of a multiplexed ADC in industrial DAQ systems. Internally compensated unity-gain stability simplifies unity-gain Sallen-Key topologies. Keep resistor values in the 10k to 100k range so class-AB output loading stays light and phase margin remains robust.
推薦
Comparator and Threshold Detection Circuits
While dedicated comparators are preferred for fast switching, the LM2902PW economically handles slow threshold detection in cost-sensitive boards: over-temperature alarms from NTC bridges, undervoltage detection on 12 V rails, and window comparators using two of the four channels per signal. Ground-including common-mode input lets the threshold sit at 0 V. Note the output stage is not open-collector, so wire-AND logic requires external diodes. Typical response is adequate for millisecond-class supervisory decisions at 1.2 MHz available bandwidth with modest slew rate.
推薦
Audio Signal Distribution in Consumer Hardware
In cost-driven consumer and communication hardware, the LM2902PW distributes and buffers line-level audio: microphone preamplification, summing mixers, and output drivers into headphone buffers. The four matched channels support stereo processing plus two aux paths in one TSSOP-14 footprint. Bandwidth of 1.2 MHz covers the full audio band with margin, and single-supply operation from 5 V or 12 V rails simplifies power design with a mid-supply virtual ground from a spare channel. Expect modest noise and THD suited to intercom, PA, and telephony-class audio rather than hi-fi.
推薦
推薦產品摘要
工程參考資料,適用於 LM2902PW — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | LM2902BPW | LM324BPW | LM324PW | NJM2902 |
|---|---|---|---|---|---|
| Package | TSSOP-14 (PW) | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 (PW) - same | TSSOP-14 equivalent (verify suffix) |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | New Japan Radio (Nisshinbo) |
| Supply Voltage Range | Up to 26 V | 3 V to 36 V | 3 V to 36 V | Up to 32 V | Up to 26 V class |
| Gain-Bandwidth Product | 1.2 MHz | 1.2 MHz class | 1.2 MHz class | 1.2 MHz class | 1.2 MHz class |
| Input Offset Voltage | 2 mV max | 3 mV max (B version) | 3 mV max (B version) | 2 mV class | 2 mV class |
| Operating Temperature | -40C to +125C | -40C to +125C | -40C to +125C | 0C to +70C | -40C to +85C class (verify suffix) |
| Drop-In Status | Baseline part | TI-listed drop-in replacement | TI-listed drop-in replacement | Same pinout, temperature-grade substitution | Cross-brand pin-compatible equivalent |
| Common-Mode Input Range | Includes ground | Includes ground | Includes ground | Includes ground | Includes ground |
主要差異化特點
- Ground-including common-mode input range (對比LM324PW)
- Cost-neutral next-generation upgrade path (對比LM2902BPW)
- Cross-brand second source availability (對比NJM2902)
設計說明
Decouple the V+ pin (pin 4) with a 100 nF ceramic capacitor placed within a few millimeters of the pin, plus a 10 uF bulk capacitor per board. The LM2902 draws roughly 0.8 mA per amplifier (typical, per datasheet), largely independent of supply voltage, so thermal design is rarely a concern; estimated dissipation at 26 V supply is about 21 mV* mA-class, negligible for the TSSOP-14 package. Verify total supply current in four-channel designs still meets your power budget at the cold and hot temperature corners.
Two common failure modes: (1) expecting rail-to-rail output - the LM2902 output swings to within roughly 1.5 V of the positive rail at light load and near ground on the low side, so a 5 V single supply yields about a 0 V to 3.5 V usable output span; design gain stages so expected peaks fit. (2) leaving unused amplifiers floating - tie unused non-inverting inputs to mid-supply and connect the stages as unity-gain followers to prevent parasitic oscillation coupling into used channels.
Keep feedback resistors in the 10k to 100k range so class-AB output stages are not overloaded; at very low resistor values the output drive and offset-induced error degrade. Route input traces short and guard high-impedance nodes with ground pour to limit leakage and noise pickup. The TSSOP-14 footprint has no exposed pad, so thermal relief is unnecessary, but maintain a clean ground under the part for four-channel channel-to-channel crosstalk control, which improves when return currents share a solid reference plane.
合規資訊
RoHS compliance per standard TI commodity-part status; confirm REACH, halogen-free, and conflict-minerals declarations through TI's product stewardship portal for your exact orderable suffix.