LM2903IMX - Dual 36V Comparator | onsemi | Industrial
N.º da peça: LM2903IMX ✓ AtivoLM2903IMX Visão geral
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input, or vice versa. The LM2903 belongs to the comparator hierarchy within analog ICs and interface ICs. Unlike an operational amplifier, its primary function is threshold switching rather than linear amplification. This distinction makes the LM2903IMX suitable for sensing, protection, control, and digital-interface applications.
The LM2903IMX operates from a single supply as high as 36 V, which supports industrial control systems operating from 24 V rails. Its common-mode input range includes ground, allowing signals close to 0 V to be compared in single-supply systems. Typical supply current is approximately 800 µA, while the 1.5 µs response time supports detection functions that require faster switching than a general-purpose slow comparator.
Both comparison channels operate independently, reducing the component count in designs that require two threshold decisions. The open-collector outputs require pull-up resistors to define the inactive output voltage, but this architecture provides useful system-level flexibility: pull-ups can be connected to a local supply, interface voltage, or pull-up network. Input, output, and supply functions are arranged in a standard 8-SOIC footprint suitable for leaded through-hole assembly.
Typical uses include 24 V industrial sensor interfaces, battery-powered monitoring circuits, overvoltage and undervoltage detection, window-comparator functions, and logic-level translation between open-collector devices. The broad supply range is particularly useful when a comparator must operate directly from an unregulated industrial rail while its output drives a pull-up connected to a lower-voltage logic domain.
Designers should verify the logic thresholds, output sink current, input bias current, and pull-up voltage against the system requirements. Place the pull-up resistor close to the open-collector output, maintain a common ground return between the comparator and sensed circuitry, and avoid exceeding the 36 V maximum supply voltage. The 8-SOIC package is not the smallest option, but it supports straightforward prototyping and hand assembly.
This page combines the LM2903IMX operating limits, pin assignments, drop-in replacement options, application guidance, and design considerations to provide practical information for PCB planning, circuit design, and component selection.
Alternativas drop-in para LM2903IMX — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2903IMX (mesmo formato e footprint) — diferindo em Package, Input Common-Mode Range, Propagation Delay, Operating Temperature Range, Maximum Supply Voltage.
LM2903D
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903DRG4
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903MX/NOPB
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903AVQDRQ1
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903BIDR
✅ Drop-InConsulte o preço
Ver ficha técnica →NJM2903M-
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2903IMX Classificações máximas e características elétricas
| Comparator Type | Dual differential comparator |
| Number of Comparison Channels | 2 channels |
| Single-Supply Operating Voltage | 2 V to 36 V |
| Dual-Supply Operating Voltage | ±1 V to ±18 V |
| Typical Response Time | 1.5 µs |
| Typical Supply Current | 800 µA |
| Tipo de saída | Open-collector |
| Input Common-Mode Range | Includes ground |
| Number of Inputs | 4 differential inputs |
| Número de saídas | 2 outputs |
| Encapsulamento | 8-SOIC, 3.90 mm width |
| Tipo de montagem | Surface mount |
| Packaging | Tape and reel |
| Logic Compatibility | Compatible with TTL and CMOS logic |
| Single-Supply Comparison Near Ground | Supported |
Configuração de pinos do LM2903IMX
| Pino 1 | OUT1 — Comparator 1 open-collector output |
| Pino 2 | IN1- — Comparator 1 inverting input |
| Pino 3 | IN1+ — Comparator 1 non-inverting input |
| Pino 4 | GND — Ground connection |
| Pino 5 | IN2+ — Comparator 2 non-inverting input |
| Pino 6 | IN2- — Comparator 2 inverting input |
| Pino 7 | OUT2 — Comparator 2 open-collector output |
| Pino 8 | VCC — Positive supply connection |
Aplicações típicas
LM2903IMX é adequado para 6 aplicaçãos: Industrial 24V Sensor Interface, Battery-Powered Threshold Detection, Overvoltage and Undervoltage Protection, Window Comparator for Supply Limits, Open-Collector Logic Interface, Automotive and Heavy Equipment Control.
Industrial 24V Sensor Interface
The LM2903IMX is suited to industrial sensor interfaces that operate from a 24 V control rail. Its single-supply range extends to 36 V, providing 12 V of nominal supply headroom at 24 V, while the common-mode input range includes ground for sensors that produce signals near 0 V. The dual architecture can monitor two independent sensor thresholds without adding another comparator package. The approximately 1.5 µs response time provides quicker switching than a slow general-purpose comparator, while approximately 800 µA typical supply current limits continuous overhead. Because the outputs are open collector, pull-ups can connect to a local 3.3 V or 5 V logic rail, allowing a 24 V sensing circuit to interface directly with lower-voltage digital hardware without tying the output voltage to the input supply.
Recomendado
Battery-Powered Threshold Detection
LM2903IMX fits battery-powered threshold detection where low quiescent consumption and operation from a single rail are important. Its 2 V minimum supply supports low-energy systems, and the typical supply current of approximately 800 µA provides a defined baseline for battery-life calculations. The common-mode range including ground makes it useful for detecting battery pack limits, charger-state signals, or divided voltages that approach zero. The approximately 1.5 µs response time is useful when the monitored condition changes quickly, although input overdrive affects effective delay. Two independent channels allow the same device to monitor an upper and lower threshold. Designers should calculate the resistor-divider current, comparator input bias effect, pull-up current, and battery leakage together rather than considering only the approximately 800 µA internal supply drain.
Recomendado
Overvoltage and Undervoltage Protection
The LM2903IMX can implement independent overvoltage and undervoltage protection channels in power-control equipment. Each internal comparator evaluates a divided or scaled input against a reference, while the 2 V to 36 V supply range allows the device to operate from a 24 V bus without requiring a separate low-voltage supply. The approximately 1.5 µs typical response time supports protection against fast transient excursions, subject to the actual sensing network and filter selection. The open-collector outputs can directly pull down a system fault line or latch a logic node through a pull-up resistor. For dependable fault detection, account for comparator offset and input bias current when setting thresholds, and place filtering close to the input when a slow fault signal must be distinguished from a brief disturbance.
Recomendado
Window Comparator for Supply Limits
A window-comparator circuit built with the LM2903IMX can flag a monitored voltage whenever it falls below a lower limit or rises above an upper limit. The device's two independent channels make this arrangement more compact than using two separate comparator ICs. Its single-supply capability reaches 36 V, so a 24 V rail can be monitored directly, while the input common-mode range includes ground for lower rail thresholds. Each open-collector output can be wired to a common fault or alarm node with suitable pull-up resistors, allowing the outputs to combine without tying the interface voltage to the 24 V supply. Practical threshold design should include resistor tolerance, input offset voltage, and temperature effects. Additional filtering may be required if the target rail contains switching ripple that could repeatedly cross a limit.
Recomendado
Open-Collector Logic Interface
The LM2903IMX can provide an open-collector interface between analog sensing circuitry and digital logic. The pull-up resistor may connect to a 3.3 V, 5 V, or other logic rail independently of the comparator supply, enabling level translation without a dedicated translator IC. According to the manufacturer datasheet, the output arrangement is compatible with TTL and CMOS logic. The approximately 1.5 µs response time gives adequate performance for ordinary control, acknowledgment, and fault signals, while the two channels can handle separate bus-related decisions. Designers should verify the pull-up voltage against the receiving device's input limits, confirm the comparator's output sink capability, and use a resistor value that balances low-voltage logic rise time against power consumption. The 8-SOIC footprint also keeps the interface accessible during prototype assembly.
Recomendado
Automotive and Heavy Equipment Control
The LM2903IMX can be used in control and protection functions for industrial equipment, while the LM2903AVQDRQ1 provides a qualified alternative where automotive requirements apply. The comparator accepts a single supply up to 36 V and can sense inputs near ground, matching 12 V and 24 V vehicle or machinery electrical systems. Its approximately 1.5 µs response time supports relatively prompt decisions, and the dual configuration provides two thresholds in one 8-SOIC package. Open-collector outputs simplify attachment to 12 V or 24 V fault lines when a pull-up is present. Vehicle or safety-related designs should select the appropriate qualification level, transient protection, grounding strategy, and decoupling rather than relying on the base comparator qualification alone. PCB layout should keep sensing and pull-up loops compact to reduce susceptibility to electrical noise.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2903IMX — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Choose LM2903AVQDRQ1 when an automotive-qualified 8-SOIC option is required; choose LM2903D, LM2903DRG4, or LM2903MX/NOPB when TI sourcing is preferable. The 3PEAK LM2903 and NJM2903M-(T1) are additional LM2903-family sourcing candidates, but their exact electrical limits, qualification status, and ordering suffixes should be checked before substitution. Because all listed candidates use the 8-SOIC footprint, PCB changes are generally unnecessary. Nevertheless, verify pin assignments, supply voltage, input common-mode range, output sink current, operating temperature, pull-up requirements, and qualification status before approving any alternative for production.
Comparação com alternativas
| Parâmetro | Este produto | LM2903D | LM2903DRG4 | LM2903MX/NOPB | LM2903AVQDRQ1 | LM2903 | NJM2903M-(T1) |
|---|---|---|---|---|---|---|---|
| Brand | onsemi | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | 3PEAK | Japan Radio Co. |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Single-Supply Maximum | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V | 36 V |
| Split-Supply Maximum | ±18 V | ±18 V | ±18 V | ±18 V | ±18 V | ±18 V | ±18 V |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
Principais diferenciais
- High-voltage single-supply operation reduces the need for a separate low-voltage sensing device (vs LM2903D)
- Automotive-qualified option is available in the same functional family and footprint (vs LM2903AVQDRQ1)
- Low-voltage dual comparison supports compact battery and threshold designs (vs NJM2903M-(T1))
Notas de projeto
Do not treat the open-collector output as actively driven high. Each output requires a pull-up resistor, and that resistor's supply determines the high output voltage. Confirm that this voltage is valid for the receiving TTL or CMOS input. Also verify the maximum supply remains at or below 36 V, because transient industrial or automotive rails can exceed a nominal 24 V rail even when the steady-state operating voltage is acceptable.
Place each output pull-up resistor close to the corresponding OUT pin and maintain a common ground reference between the comparator, its input divider, and the sensed circuit. Keep the high-impedance input traces short and away from switching nodes. If a monitored rail contains ripple, add filtering at the input rather than relying on the approximately 1.5 µs switching time to reject noise; comparator speed does not prevent false threshold crossings.
Estimated: when the 8-SOIC device operates from 24 V with both outputs sinking 10 mA, the transistor output-path dissipation is approximately 24 V × 0.010 A = 0.24 W, excluding internal supply current. At 36 V and the same 10 mA sink current, estimated output-path dissipation rises to approximately 0.36 W. Use the actual maximum continuous sink current and the manufacturer's thermal data to determine whether copper area or thermal relief is required.
Informações de conformidade
Compliance attributes were not identified for the exact LM2903IMX ordering code. The LM2903AVQDRQ1 naming identifies an automotive-qualified alternative, but that qualification does not establish the status of LM2903IMX.