LM2903QTH-13 Dual 36V Comparator, TSSOP-8 | Diodes Inc
N.º da peça: LM2903QTH-13 ✓ AtivoLM2903QTH-13 Visão geral
A voltage comparator is an analog integrated circuit that compares two input voltages and converts the result into a logic-level output that indicates which input is higher. Within the semiconductor hierarchy, a comparator sits in the linear IC family alongside op amps and voltage references, and it is the simplest building block for threshold detection, level translation and open-loop control functions.
Key features of the LM2903QTH-13 include AEC-Q100 Grade 1 automotive qualification, RoHS3 and REACH compliance, MSL Level 1 moisture sensitivity, and the use of green mold compound, all supporting automotive programs that require PPAP documentation. The device shares industry-standard 8-pin pinouts with the wider LM2903 and LM393 families, which makes board requalification and cross-brand second sourcing straightforward. Low quiescent current keeps the part attractive for always-on battery-powered sensing systems.
Technically, the device contains two independent amplifier and output stages. Each channel offers differential inputs and an open-collector (open-drain) output stage, so an external pull-up resistor is required on every output. The wide 36 V supply ceiling allows the inputs and outputs to sit well above the logic rail of the controlling MCU, simplifying direct interface to 5 V, 12 V or 24 V systems without level shifters. The low input bias and offset currents minimize error when driving high-impedance sensor networks.
Typical applications include automotive sensor interface and battery monitoring, industrial control and threshold detection, DC-DC converter current-limit loops, over-temperature protection circuits in power modules, and general-purpose logic level shifting where a pulled-up open-collector output is acceptable.
When designing with the LM2903QTH-13, always fit pull-up resistors on OUT1 and OUT2, keep input common-mode voltage inside the supply range, and give each supply pin a local 100 nF decoupling capacitor close to the pad. Tie the unused channel inputs to a defined voltage within the supply range so that output state stays predictable.
This page brings together verified distributor listings, drop-in alternatives across TI and Diodes, pin-level detail and practical layout notes that go beyond the basic orderable-parts listings.
Alternativas drop-in para LM2903QTH-13 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2903QTH-13 (mesmo formato e footprint) — diferindo em Comparator Type, Input Offset Voltage, Package, Supply Current, Input Bias Current.
LM2903AQTH-13
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903BIDR
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903-Q1
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2903B-Q1
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2903QTH-13 Classificações máximas e características elétricas
| Device Type | Dual differential voltage comparator |
| Number of Channels | 2 |
| Comparator Type | Standard (General Purpose) |
| Maximum Supply Voltage | 36 V |
| Input Offset Voltage | 2 mV |
| Input Bias Current | 25 nA |
| Input Offset Current | 5 nA |
| Corrente de alimentação | 0.6 mA per channel |
| Configuração de saída | Open-collector (open-drain), requires external pull-up |
| Encapsulamento | 8-TSSOP |
| Contagem de pinos | 8 pins |
| Tipo de montagem | Surface Mount |
| Automotive Qualification | AEC-Q100 Grade 1 |
| Status RoHS | RoHS3 compliant |
| REACH Status | REACH compliant |
| Moisture Sensitivity Level | MSL Level 1 |
| Mold Compound | Green mold compound |
| PPAP Support | Supported |
Configuração de pinos do LM2903QTH-13
| Pino 1 | OUT1 — Comparator 1 output (open collector), requires external pull-up resistor |
| Pino 2 | IN1- — Comparator 1 inverting input |
| Pino 3 | IN1+ — Comparator 1 non-inverting input |
| Pino 4 | GND — Ground / negative supply reference |
| Pino 5 | IN2+ — Comparator 2 non-inverting input |
| Pino 6 | IN2- — Comparator 2 inverting input |
| Pino 7 | OUT2 — Comparator 2 output (open collector), requires external pull-up resistor |
| Pino 8 | VCC — Positive supply input |
Aplicações típicas
LM2903QTH-13 é adequado para 6 aplicaçãos: Automotive Battery Monitoring and Threshold Detection, DC-DC Converter Current-Limit and Feedback Loops, Industrial Sensor Interface and Level Conditioning, Over-Temperature and Thermal Protection in Power Modules, Oscillator and Relaxation Timing Circuits, General-Purpose Logic Level Shifting.
Automotive Battery Monitoring and Threshold Detection
The LM2903QTH-13 suits 12 V and 24 V vehicle battery monitoring because its 36 V maximum supply rating tolerates load-dump and cranking transients that would exceed lower-voltage comparators. Each channel compares a divided battery rail against a precision reference to flag over-voltage or under-voltage conditions. AEC-Q100 Grade 1 qualification, green mold compound and PPAP support satisfy automotive sourcing requirements, and the 25 nA input bias current minimises error when sensing through high-value dividers. Note that the open-collector outputs need pull-up resistors so the flags can be wired to a ground-referenced vehicle logic input.
Recomendado
DC-DC Converter Current-Limit and Feedback Loops
In a current-mode DC-DC converter, the LM2903QTH-13 can be used as the comparator in the peak-current-sense loop, comparing the voltage across a sense resistor against a control ramp. The 0.6 mA supply current per channel keeps the comparator bias negligible against the sense signal, and the 2 mV offset translates directly into current-sense error at the shunt. The open-collector output drives the compensation node or cycle-by-cycle control latch. Its wide 36 V ceiling lets the sense node operate directly on 12 V or 24 V rails without a level-shifting pre-amplifier.
Recomendado
Industrial Sensor Interface and Level Conditioning
The LM2903QTH-13 conditions weak sensor outputs into clean logic levels for industrial PLCs and data acquisition systems. With 25 nA input bias current and 5 nA input offset current, the inputs impose negligible loading on high-impedance dividers, thermocouple-style networks and capacitive sensing front ends, so the 2 mV offset dominates the error budget rather than bias effects. The 36 V supply headroom accepts directly connected 24 V sensor loops. Pull the open-collector output up to the PLC input threshold and the comparator delivers a rail-to-rail digital flag with the noise immunity expected from an industrial comparator.
Recomendado
Over-Temperature and Thermal Protection in Power Modules
Power modules and motor drives commonly need a local thermal shutdown that does not depend on a host microcontroller. The LM2903QTH-13 can compare the output of a remote temperature sensor against an internal reference to trip a fault signal, and the 36 V supply rating lets it sit alongside the power stage without level shifting. Its low 0.6 mA per-channel supply current supports continuous monitoring without meaningful power penalty. Because the outputs are open-collector, several devices can be wired to a common fault line, and the pull-up resistor can be placed at the system connector for robust fault signalling.
Recomendado
Oscillator and Relaxation Timing Circuits
The LM2903QTH-13 works as the timing element in LC or RC oscillator circuits used for clock generation, sensor excitation and simple LED drivers. Its two independent channels allow one channel to provide the reference threshold while the other provides the feedback comparison, and the very low input bias current preserves the timing accuracy of high-value feedback resistors. The 0.6 mA supply current per channel keeps battery-powered oscillators running longer than a higher-quiescent alternative. Select the external resistor and capacitor values from the manufacturer typical application circuits, and remember that output pull-up resistance also affects the duty cycle of the oscillator.
Recomendado
General-Purpose Logic Level Shifting
When a 5 V or 3.3 V logic domain must be driven from a 12 V or 24 V signal, the LM2903QTH-13 performs the shift with a single part. The comparator input accepts the higher-voltage signal directly within its 36 V supply ceiling, and the open-collector output pulled up to the lower-voltage logic rail produces a clean, standards-compliant transition in the receiving domain. Because the output stage only pulls low, the receiving device is never exposed to the higher voltage. This arrangement is common in industrial and automotive gateways where several legacy 24 V discrete signals must be adapted to a modern MCU, and it removes the need for dedicated transistor level-shifter stages.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2903QTH-13 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2903AQTH-13 | LM2903 | LM2903-Q1 | LM2903B-Q1 |
|---|---|---|---|---|---|
| Package | 8-TSSOP | 8-TSSOP - same | 8-TSSOP - same | 8-TSSOP - same | 8-TSSOP - same |
| Brand | Diodes Incorporated | Diodes Incorporated | Texas Instruments | Texas Instruments | Texas Instruments |
| Maximum Supply Voltage | 36 V | 36 V | 36 V | 36 V | 36 V |
| Output Configuration | Open-collector, external pull-up required | Open-collector | Open-collector | Open-collector | Open-collector |
| Number of Channels | 2 | 2 | 2 | 2 | 2 |
Principais diferenciais
- Single-manufacturer automotive-qualified source in a common 8-TSSOP footprint (vs LM2903B-Q1)
- Precision-grade upgrade path without footprint change (vs LM2903AQTH-13)
- Wide 36 V supply ceiling for direct 24 V industrial and automotive interface (vs LM2903-Q1)
- Low quiescent current keeps always-on monitoring cheap (vs LM2903)
Notas de projeto
The most common integration error with this device is forgetting the pull-up resistors on OUT1 and OUT2. The output stage is open-collector, so without a pull-up the outputs float at an undefined level and can sit in the linear region, drawing excess current and producing undefined logic at the receiving MCU. Place a pull-up to the destination logic rail, typically 4.7 kOhm to 10 kOhm, close to the output pin, and confirm the resulting rise time meets the receiver's setup requirement.
Place the 100 nF ceramic decoupling capacitor between the VCC pin (pin 8) and GND (pin 4) as close to the device as the layout allows, with the ground connection taking the shortest possible path to the ground plane. Comparator input nodes are high impedance, so keep the IN+ and IN- traces short and routed away from supply rails, inductors and switching nodes. If the device senses a signal derived from a switching converter, add the usual return-path discipline so output jitter is not coupled in through the input traces.
Ensure both input voltages of each channel stay between the negative supply rail and the positive supply rail, including during startup and shutdown transients; overdriving a comparator input outside the supply range can cause latch-up or damage even though the part is rated to 36 V. Also treat the unused channel carefully: tie both of its inputs to a defined voltage inside the supply range so the unused output does not chatter and inject noise into adjacent circuitry.
Because the open-collector output actively pulls down to ground during switching, the pull-up network and the trace leading to the receiver form a small current loop that can radiate. Keep the pull-up resistor close to the output pin and the receiving device input close to the connector or destination IC, and avoid routing the pulled-up output next to sensitive analog inputs in signal-conditioning channels. In motor-drive and relay-adjacent boards, maintain separation between comparator outputs and power-stage switching nodes.
Informações de conformidade
RoHS3 compliant, REACH compliant, MSL Level 1, AEC-Q100 Grade 1 qualified, green mold compound, automotive compliant with PPAP support per the manufacturer datasheet.