Diodes Incorporated

LM2903QTH-13 Dual 36V Comparator, TSSOP-8 | Diodes Inc

MPN: LM2903QTH-13 ✓ פעיל
36 V Vdss 25 nA Id 8-TSSOP Package
כמות הזמנה מינימלית: 1 |

LM2903QTH-13 סקירה

The Diodes Incorporated LM2903QTH-13 is a dual differential voltage comparator with two independent precision channels, a 36 V maximum supply rating, 2 mV input offset voltage, 25 nA input bias current and 0.6 mA typical supply current per channel, housed in an 8-pin TSSOP surface-mount package.

A voltage comparator is an analog integrated circuit that compares two input voltages and converts the result into a logic-level output that indicates which input is higher. Within the semiconductor hierarchy, a comparator sits in the linear IC family alongside op amps and voltage references, and it is the simplest building block for threshold detection, level translation and open-loop control functions.

Key features of the LM2903QTH-13 include AEC-Q100 Grade 1 automotive qualification, RoHS3 and REACH compliance, MSL Level 1 moisture sensitivity, and the use of green mold compound, all supporting automotive programs that require PPAP documentation. The device shares industry-standard 8-pin pinouts with the wider LM2903 and LM393 families, which makes board requalification and cross-brand second sourcing straightforward. Low quiescent current keeps the part attractive for always-on battery-powered sensing systems.

Technically, the device contains two independent amplifier and output stages. Each channel offers differential inputs and an open-collector (open-drain) output stage, so an external pull-up resistor is required on every output. The wide 36 V supply ceiling allows the inputs and outputs to sit well above the logic rail of the controlling MCU, simplifying direct interface to 5 V, 12 V or 24 V systems without level shifters. The low input bias and offset currents minimize error when driving high-impedance sensor networks.

Typical applications include automotive sensor interface and battery monitoring, industrial control and threshold detection, DC-DC converter current-limit loops, over-temperature protection circuits in power modules, and general-purpose logic level shifting where a pulled-up open-collector output is acceptable.

When designing with the LM2903QTH-13, always fit pull-up resistors on OUT1 and OUT2, keep input common-mode voltage inside the supply range, and give each supply pin a local 100 nF decoupling capacitor close to the pad. Tie the unused channel inputs to a defined voltage within the supply range so that output state stays predictable.

This page brings together verified distributor listings, drop-in alternatives across TI and Diodes, pin-level detail and practical layout notes that go beyond the basic orderable-parts listings.

חלופות תחליף ישיר עבור LM2903QTH-13 — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם LM2903QTH-13 (אותו גורם צורה וטביעת רגל) — שונים ב Comparator Type, Input Offset Voltage, Package, Supply Current, Input Bias Current.

Diodes Incorporated
Comparator Type: Dual differential voltage comparator
Input Offset Voltage: 1 mV
Package: 8-pin TSSOP
השווה עם LM2903QTH-13 →
Texas Instruments
Comparator Type: Dual differential comparator
Input Offset Voltage: 0.37 mV
Package: 8-pin SOIC (D)
השווה עם LM2903QTH-13 →

LM2903AQTH-13

✅ Drop-In
Diodes Incorporated
📦 8-TSSOP
Dual differential voltage comparator · 2 · 36 V · 1 mV · 2 mV · Includes ground · Equal to the power-supply voltage · 200 mV at 4 mA

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

LM2903BIDR

✅ Drop-In
Texas Instruments
📦 8-TSSOP
Dual differential comparator · 2 channels · Open-collector · 36 V · 2 V · 0.37 mV · 3.5 nA · 200 µA per comparator

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

LM2903-Q1

✅ Drop-In
📦 8-TSSOP
Automotive-qualified dual comparator in the same TSSOP-8 footprint with the same pin-for-pin functionality and lower offset voltage than the standard grade

📋 חלופה להתייחסות (לא בקטלוג)

LM2903B-Q1

✅ Drop-In
📦 8-TSSOP
Next-generation LM2903-Q1 family with lower offset, lower supply and input bias current, lower propagation delay and improved 2 kV ESD versus the Diodes standard grade

📋 חלופה להתייחסות (לא בקטלוג)

LM2903QTH-13 דירוגים מרביים ומאפיינים חשמליים

Device Type Dual differential voltage comparator
Number of Channels 2
Comparator Type Standard (General Purpose)
Maximum Supply Voltage 36 V
Input Offset Voltage 2 mV
Input Bias Current 25 nA
Input Offset Current 5 nA
זרם אספקה 0.6 mA per channel
תצורת מוצא Open-collector (open-drain), requires external pull-up
מארז 8-TSSOP
מספר פינים 8 pins
סוג הרכבה Surface Mount
Automotive Qualification AEC-Q100 Grade 1
סטטוס RoHS RoHS3 compliant
REACH Status REACH compliant
Moisture Sensitivity Level MSL Level 1
Mold Compound Green mold compound
PPAP Support Supported

תצורת פינים של LM2903QTH-13

TSSOP-8 Package Pinout Diagram TSSOP-8 8-pin thin shrink small outline, P0.65mm, JEDEC MO-153. 1 8 2 7 3 6 4 5 TSSOP-8
פין 1 OUT1 — Comparator 1 output (open collector), requires external pull-up resistor
פין 2 IN1- — Comparator 1 inverting input
פין 3 IN1+ — Comparator 1 non-inverting input
פין 4 GND — Ground / negative supply reference
פין 5 IN2+ — Comparator 2 non-inverting input
פין 6 IN2- — Comparator 2 inverting input
פין 7 OUT2 — Comparator 2 output (open collector), requires external pull-up resistor
פין 8 VCC — Positive supply input

יישומים טיפוסיים

LM2903QTH-13 מתאים עבור 6 יישוםs: Automotive Battery Monitoring and Threshold Detection, DC-DC Converter Current-Limit and Feedback Loops, Industrial Sensor Interface and Level Conditioning, Over-Temperature and Thermal Protection in Power Modules, Oscillator and Relaxation Timing Circuits, General-Purpose Logic Level Shifting.

🚗

Automotive Battery Monitoring and Threshold Detection

The LM2903QTH-13 suits 12 V and 24 V vehicle battery monitoring because its 36 V maximum supply rating tolerates load-dump and cranking transients that would exceed lower-voltage comparators. Each channel compares a divided battery rail against a precision reference to flag over-voltage or under-voltage conditions. AEC-Q100 Grade 1 qualification, green mold compound and PPAP support satisfy automotive sourcing requirements, and the 25 nA input bias current minimises error when sensing through high-value dividers. Note that the open-collector outputs need pull-up resistors so the flags can be wired to a ground-referenced vehicle logic input.

⚡

DC-DC Converter Current-Limit and Feedback Loops

In a current-mode DC-DC converter, the LM2903QTH-13 can be used as the comparator in the peak-current-sense loop, comparing the voltage across a sense resistor against a control ramp. The 0.6 mA supply current per channel keeps the comparator bias negligible against the sense signal, and the 2 mV offset translates directly into current-sense error at the shunt. The open-collector output drives the compensation node or cycle-by-cycle control latch. Its wide 36 V ceiling lets the sense node operate directly on 12 V or 24 V rails without a level-shifting pre-amplifier.

🏭

Industrial Sensor Interface and Level Conditioning

The LM2903QTH-13 conditions weak sensor outputs into clean logic levels for industrial PLCs and data acquisition systems. With 25 nA input bias current and 5 nA input offset current, the inputs impose negligible loading on high-impedance dividers, thermocouple-style networks and capacitive sensing front ends, so the 2 mV offset dominates the error budget rather than bias effects. The 36 V supply headroom accepts directly connected 24 V sensor loops. Pull the open-collector output up to the PLC input threshold and the comparator delivers a rail-to-rail digital flag with the noise immunity expected from an industrial comparator.

🏭

Over-Temperature and Thermal Protection in Power Modules

Power modules and motor drives commonly need a local thermal shutdown that does not depend on a host microcontroller. The LM2903QTH-13 can compare the output of a remote temperature sensor against an internal reference to trip a fault signal, and the 36 V supply rating lets it sit alongside the power stage without level shifting. Its low 0.6 mA per-channel supply current supports continuous monitoring without meaningful power penalty. Because the outputs are open-collector, several devices can be wired to a common fault line, and the pull-up resistor can be placed at the system connector for robust fault signalling.

🔧

Oscillator and Relaxation Timing Circuits

The LM2903QTH-13 works as the timing element in LC or RC oscillator circuits used for clock generation, sensor excitation and simple LED drivers. Its two independent channels allow one channel to provide the reference threshold while the other provides the feedback comparison, and the very low input bias current preserves the timing accuracy of high-value feedback resistors. The 0.6 mA supply current per channel keeps battery-powered oscillators running longer than a higher-quiescent alternative. Select the external resistor and capacitor values from the manufacturer typical application circuits, and remember that output pull-up resistance also affects the duty cycle of the oscillator.

🌐

General-Purpose Logic Level Shifting

When a 5 V or 3.3 V logic domain must be driven from a 12 V or 24 V signal, the LM2903QTH-13 performs the shift with a single part. The comparator input accepts the higher-voltage signal directly within its 36 V supply ceiling, and the open-collector output pulled up to the lower-voltage logic rail produces a clean, standards-compliant transition in the receiving domain. Because the output stage only pulls low, the receiving device is never exposed to the higher voltage. This arrangement is common in industrial and automotive gateways where several legacy 24 V discrete signals must be adapted to a modern MCU, and it removes the need for dedicated transistor level-shifter stages.

What is the LM2903QTH-13?
The LM2903QTH-13 is a dual precision differential voltage comparator from Diodes Incorporated with two independent channels, a 36 V maximum supply rating, 2 mV input offset voltage and 25 nA input bias current, supplied in an 8-pin TSSOP package. According to the manufacturer datasheet, the LM2903Q/LM2903AQ dual devices are available in SO-8, MSOP-8 and TSSOP-8 packages using industry-standard pinouts, and all variants use green mold compound qualified to AEC-Q100 Grade 1 for automotive-compliant programs.
Where can I download the LM2903QTH-13 datasheet PDF?
The LM2903QTH-13 datasheet PDF is available from the manufacturer product listing and from distributor-hosted copies such as the Digi Electronics mirror of the Diodes Incorporated document. The datasheet covers the LM2901Q/LM2903Q family electrical characteristics, the LM2901AQ/LM2903AQ precision variants, package options, pin assignments and typical application circuits. Use the pin description and package drawings section when assigning PCB tracks for the 8-pin TSSOP footprint.
What is the pinout of the LM2903QTH-13 8-pin TSSOP?
The LM2903QTH-13 uses the standard 8-pin dual comparator pinout: pin 1 is OUT1, pin 2 is IN1-, pin 3 is IN1+, pin 4 is GND, pin 5 is IN2+, pin 6 is IN2-, pin 7 is OUT2 and pin 8 is VCC. The manufacturer documents that the LM2903Q/LM2903AQ duals are supplied in industry-standard pinouts across SO-8, MSOP-8 and TSSOP-8 packages, which allows a direct footprint match with LM393-family devices.
Does the LM2903QTH-13 output need a pull-up resistor?
Yes. The LM2903QTH-13 uses an open-collector (open-drain) output stage on each channel, so both OUT1 and OUT2 require an external pull-up resistor to a valid logic supply. The resistor sets the rise time and the high-level voltage, so a typical value of 10 kOhm to 10 kOhm is common in signal-paced applications. Without a pull-up the output floats, and the device cannot drive a CMOS input reliably.
What is the difference between LM2903QTH-13 and LM2903AQTH-13?
The LM2903QTH-13 is the standard-grade member of the dual comparator family while the LM2903AQTH-13 is the precision A-variant. According to the Diodes Incorporated datasheet, both the LM2903Q and LM2903AQ dual devices are offered in the same SO-8, MSOP-8 and TSSOP-8 packages with identical industry-standard pinouts. The A version is selected when tighter offset voltage and reduced input bias current are needed at higher cost, so the two are drop-in compatible in the same 8-pin TSSOP footprint.
What is the best drop-in replacement for the LM2903QTH-13?
The closest drop-in replacement is the LM2903AQTH-13 from the same manufacturer, which shares the 8-pin TSSOP footprint, pinout and AEC-Q100 Grade 1 automotive qualification while improving offset and bias characteristics. Cross-brand options include the Texas Instruments LM2903, LM2903-Q1 and LM2903B-Q1, all available in TSSOP-8 with the same industry-standard dual comparator pinout, making them usable where second-sourcing across manufacturers is required.
Is the LM2903QTH-13 suitable for automotive applications?
Yes. The LM2903QTH-13 is qualified to AEC-Q100 Grade 1 and the manufacturer datasheet states that these devices use green mold compound and are automotive compliant, supporting PPAPs. This makes the part suitable for Grade 1 automotive environments such as body electronics, battery management and sensor interface modules, provided the operating temperature grade required by your design is confirmed against the manufacturer ordering information.
Where can I buy the LM2903QTH-13 and what is the lead time?
The LM2903QTH-13 is offered through major authorized distributors and is generally listed as an active, orderable part in an 8-pin TSSOP package. Current pricing, stock and lead time change frequently, so submit the Request a Quote form on this page for a live quote against your required quantity and date code. For volume automotive programs, request a PPAP schedule and date-code traceability at the same time.
What is the price of the LM2903QTH-13?
Pricing on the LM2903QTH-13 depends on order quantity, date code and packaging, so use the Request a Quote form on this page to obtain a current quotation rather than relying on a stale figure. The part is a mature, high-volume dual comparator in the widely distributed 8-TSSOP footprint, which generally means competitive pricing at volume and readily available production capacity across multiple authorized channels.
Is the LM2903QTH-13 in stock?
Availability for the LM2903QTH-13 fluctuates with factory loading and demand cycles. The Request a Quote form on this page is the fastest way to confirm current stock, scheduled delivery and minimum order quantity for your build, and to obtain date-code and traceability information if your quality system requires it. Because the device uses a standard, high-volume TSSOP-8 package, supply is typically predictable across multiple channels.
What can replace the LM2903QTH-13?
The LM2903QTH-13 can be replaced by the Diodes Incorporated LM2903AQTH-13 for a precision upgrade in the identical 8-pin TSSOP footprint, or by the Texas Instruments LM2903, LM2903-Q1 or LM2903B-Q1, which share the same dual comparator pinout and TSSOP-8 package options. Because the family uses industry-standard pinouts across SO-8, MSOP-8 and TSSOP-8, footprint compatibility is guaranteed as long as the package variant matches.
LM2903QTH-13 vs LM2903B-Q1: which is better for industrial designs?
The Diodes Incorporated LM2903QTH-13 is AEC-Q100 Grade 1 qualified with 2 mV input offset voltage and 25 nA input bias current, while the Texas Instruments LM2903B-Q1 is the next-generation version of the industry-standard LM2903-Q1 family with lower offset voltage, higher supply voltage capability, lower supply current, lower input bias current, lower propagation delay and improved 2 kV ESD performance. Choose the LM2903B-Q1 when maximum speed and lowest offset matter, and the LM2903QTH-13 when a single-manufacturer automotive-qualified source is preferred.
When should I choose the LM2903QTH-13 over a lower-precision comparator?
Choose the LM2903QTH-13 when the sensed signal is high impedance or the threshold decision must be repeatable across temperature, because its 2 mV offset and 25 nA input bias current limit error contributions in sensor front ends. For coarse logic-level detection of a strong digital signal, a simpler comparator is sufficient. The LM2903QTH-13 also suits 24 V industrial buses, since the 36 V supply ceiling handles transients that would exceed lower-voltage parts.
What are the key specifications of the LM2903QTH-13 that engineers should know?
The LM2903QTH-13 is a dual general-purpose comparator rated to 36 V, with 2 mV input offset voltage, 25 nA input bias current, 5 nA input offset current and 0.6 mA supply current per channel, in an 8-pin TSSOP package. It is AEC-Q100 Grade 1 qualified, RoHS3 and REACH compliant, MSL Level 1, and built with green mold compound. Outputs are open-collector, so external pull-up resistors are mandatory on OUT1 and OUT2.
Is the LM2903QTH-13 the same as the LM2903?
The LM2903QTH-13 and the Texas Instruments LM2903 are functionally equivalent dual comparators from different manufacturers rather than identical parts. Both are dual precision differential comparators with very low input offset voltage, both use industry-standard 8-pin pinouts across SO-8, MSOP-8 and TSSOP-8, and both are rated to 36 V. Verify the specific offset voltage, propagation delay and automotive qualification of the exact ordering code before substituting.
How do I design the layout for the LM2903QTH-13?
Place a 100 nF ceramic decoupling capacitor directly between the VCC pin and GND pin on the same side of the board, keep the ground return path short and low-impedance, and route the differential inputs away from supply and switching nodes to preserve the 25 nA bias current and 2 mV offset performance. Use the pull-up resistor on each open-collector output close to the output pin, and follow the manufacturer package drawing for the TSSOP-8 land pattern and exposed-pad-free lead geometry.

נתוני עזר הנדסיים עבור LM2903QTH-13 — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose the LM2903QTH-13 when you need a dual general-purpose comparator with a 36 V ceiling, low 25 nA input bias current and AEC-Q100 Grade 1 automotive qualification from Diodes Incorporated, particularly for 12 V or 24 V battery monitoring and industrial sensor interfacing. Select the LM2903AQTH-13 when the threshold accuracy of the 2 mV standard grade is insufficient, since it shares the same TSSOP-8 pinout and needs no board change. Use the Texas Instruments LM2903 as a cross-brand drop-in for second sourcing, the LM2903-Q1 when an automotive-qualified alternative from a different supplier is preferred, and the LM2903B-Q1 when the lowest offset, lowest supply current, fastest propagation delay and improved 2 kV ESD performance justify changing vendor. All five options share the same 8-pin TSSOP footprint and industry-standard dual comparator pinout, but confirm the open-collector output stage requires an external pull-up resistor in every case.

השוואה עם חלופות

פרמטר מוצר זה LM2903AQTH-13 LM2903 LM2903-Q1 LM2903B-Q1
Package 8-TSSOP 8-TSSOP - same 8-TSSOP - same 8-TSSOP - same 8-TSSOP - same
Brand Diodes Incorporated Diodes Incorporated Texas Instruments Texas Instruments Texas Instruments
Maximum Supply Voltage 36 V 36 V 36 V 36 V 36 V
Output Configuration Open-collector, external pull-up required Open-collector Open-collector Open-collector Open-collector
Number of Channels 2 2 2 2 2

מבדילים עיקריים

  • Single-manufacturer automotive-qualified source in a common 8-TSSOP footprint (לעומתLM2903B-Q1)
  • Precision-grade upgrade path without footprint change (לעומתLM2903AQTH-13)
  • Wide 36 V supply ceiling for direct 24 V industrial and automotive interface (לעומתLM2903-Q1)
  • Low quiescent current keeps always-on monitoring cheap (לעומתLM2903)

הערות תכנון

The most common integration error with this device is forgetting the pull-up resistors on OUT1 and OUT2. The output stage is open-collector, so without a pull-up the outputs float at an undefined level and can sit in the linear region, drawing excess current and producing undefined logic at the receiving MCU. Place a pull-up to the destination logic rail, typically 4.7 kOhm to 10 kOhm, close to the output pin, and confirm the resulting rise time meets the receiver's setup requirement.

Place the 100 nF ceramic decoupling capacitor between the VCC pin (pin 8) and GND (pin 4) as close to the device as the layout allows, with the ground connection taking the shortest possible path to the ground plane. Comparator input nodes are high impedance, so keep the IN+ and IN- traces short and routed away from supply rails, inductors and switching nodes. If the device senses a signal derived from a switching converter, add the usual return-path discipline so output jitter is not coupled in through the input traces.

Ensure both input voltages of each channel stay between the negative supply rail and the positive supply rail, including during startup and shutdown transients; overdriving a comparator input outside the supply range can cause latch-up or damage even though the part is rated to 36 V. Also treat the unused channel carefully: tie both of its inputs to a defined voltage inside the supply range so the unused output does not chatter and inject noise into adjacent circuitry.

Because the open-collector output actively pulls down to ground during switching, the pull-up network and the trace leading to the receiver form a small current loop that can radiate. Keep the pull-up resistor close to the output pin and the receiving device input close to the connector or destination IC, and avoid routing the pulled-up output next to sensitive analog inputs in signal-conditioning channels. In motor-drive and relay-adjacent boards, maintain separation between comparator outputs and power-stage switching nodes.

מידע על תאימות

RoHS
Compliant
REACH
Compliant
AEC-Q100
Qualified
נטול עופרת
Yes
נטול הלוגנים
Yes
מינרלים של סכסוך
Unknown

RoHS3 compliant, REACH compliant, MSL Level 1, AEC-Q100 Grade 1 qualified, green mold compound, automotive compliant with PPAP support per the manufacturer datasheet.

הנתונים אומתו בתאריך: 2026-11-09 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

LM2903QTH-13 datasheet LM2903QTH-13 pinout LM2903QTH-13 datasheet pdf LM2903QTH-13 equivalent LM2903QTH-13 drop-in replacement LM2903QTH-13 price LM2903QTH-13 stock Diodes LM2903QTH-13 LM2903QTH-13 vs LM2903AQTH-13 LM2903QTH-13 TSSOP-8 dual comparator LM2903QTH-13 AEC-Q100 Grade 1 LM2903QTH-13 automotive battery monitoring LM2903 dual comparator 36V LM2903 pinout TSSOP-8

רכיבים ומונחים קשורים

Diodes Incorporated LM2903QTH-13 LM2903AQTH-13 LM2903 LM2903-Q1 LM2903B-Q1 Texas Instruments voltage comparator differential comparator analog IC linear IC semiconductor open-collector output pull-up resistor input offset voltage input bias current quiescent supply current AEC-Q100 RoHS REACH PPAP TSSOP-8 surface mount MSL Level 1 automotive electronics
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר