LM2903YDT - Dual 36V Comparator, SOIC-8 | STMicroelectronics
N.º da peça: LM2903YDT ✓ AtivoLM2903YDT Visão geral
A voltage comparator is an analog interface that compares two input voltages and produces a digital logic result indicating which input is higher. The LM2903 belongs to the comparator hierarchy, which includes differential comparators, analog interface ICs, and semiconductor signal-conditioning devices. Its two independent channels allow one package to perform two separate threshold, sorting, level-detection, or overvoltage-monitoring functions without sharing internal circuitry between channels.
Key characteristics include a supply current of 0.4 mA, low input bias current of 25 nA typical, input offset current of ±5 nA typical, and operation from +2 V to +36 V with a single supply or ±1 V to ±18 V with dual supplies. The open-collector outputs allow wired-AND logic and require an external pull-up resistor. Low input current is especially useful when sensing high-impedance sensors because it reduces the input burden and allows the source impedance to determine practical sensitivity.
The device compares two differential inputs without saturating at either supply rail. This rail-to-rail comparison behavior supports designs in which the sensed signal approaches ground or the positive supply. Because the outputs are open collector, external pull-ups can establish the logic voltage independently of the comparator supply, allowing interfacing with TTL, CMOS, MCU inputs, relay drivers, or other open-collector loads. The low 0.4 mA supply current also keeps comparator overhead low in continuously powered equipment.
Typical applications include industrial sensor thresholding, motor and valve control, battery monitoring, overvoltage detection, window-comparator functions, and digital control systems. The automotive-qualified LM2903YDT variant is particularly appropriate for vehicle electronic modules requiring a wide supply range, low quiescent current, and robust open-collector signaling. Its SOIC-8 package supports conventional reflow assembly and provides adequate pin spacing for straightforward routing.
Designers should account for open-collector output behavior, input common-mode range, offset voltage, propagation delay, and supply decoupling. Place the supply bypass capacitor close to the device and use pull-up resistors that satisfy the required rise time without excessive switching current. Verify the selected logic family’s input thresholds and check the comparator’s response time against the application’s switching requirements.
This page combines the manufacturer specifications with practical interface guidance, package-aware alternatives, and a parameter-by-parameter comparison. It is intended to help engineers determine whether the LM2903YDT fits a particular dual-comparator design and whether a same-footprint replacement is electrically acceptable.
Alternativas drop-in para LM2903YDT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com LM2903YDT (mesmo formato e footprint) — diferindo em Comparator Type, Package, Output Type, Number of Channels, Operating Temperature Range.
LM2903DT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LM2903Q2T
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903AVQDRG4Q1
✅ Drop-InConsulte o preço
Ver ficha técnica →LM2903YDT Classificações máximas e características elétricas
| Comparator Type | Dual differential voltage comparator |
| Number of Channels | 2 channels |
| Single-Supply Voltage Range | +2 V to +36 V |
| Dual-Supply Voltage Range | ±1 V to ±18 V |
| Corrente de alimentação | 0.4 mA typical |
| Power Consumption Per Comparator | 1 mW at +5 V |
| Input Bias Current | 25 nA typical |
| Input Offset Current | ±5 nA typical |
| Tipo de saída | Open collector |
| Comparison Capability | Rail-to-rail |
| Encapsulamento | 8-pin SOIC |
| Tipo de montagem | Surface mount |
| Automotive Qualification | AEC-Q100 and Q003 or equivalent |
| Advanced Screening | AEC-Q001 and Q002 or equivalent |
Guia de Configuração de Pinos do LM2903YDT 8-pin soic
Configuração de pinos para LM2903YDT (pacote 8-pin soic). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para LM2903YDT.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
LM2903YDT é adequado para 6 aplicaçãos: Automotive Battery Threshold Detection, Industrial Sensor Limit Detection, Motor and Valve Control Interface, Battery Charger Overvoltage Protection, Window Comparator for Precision Control, Embedded Control Signal Qualification.
Automotive Battery Threshold Detection
The LM2903YDT fits automotive battery monitoring because its two channels can compare separate voltage thresholds while operating from a single supply of +2 V to +36 V. The typical 0.4 mA supply current limits continuous overhead in always-on vehicle electronics, and the Y order suffix identifies an automotive-oriented qualification tier. Each open-collector output can pull up a vehicle logic input, with an external resistor setting the high level. Designers should divide the battery voltage appropriately, account for transient protection, and verify the input common-mode limits over the complete automotive electrical environment.
Recomendado
Industrial Sensor Limit Detection
The LM2903YDT is appropriate for industrial sensors whose output must be checked against a configurable threshold, especially when the sensor has high source impedance. Its 25 nA typical input bias current and ±5 nA typical input offset current reduce loading and threshold error, while two independent channels support upper and lower limits. The comparator can operate across a +2 V to +36 V supply range, simplifying designs in which the monitored signal shares a higher-voltage industrial rail. Use input protection as required, place the pull-up near the receiving logic, and avoid long high-impedance traces that can amplify noise.
Recomendado
Motor and Valve Control Interface
The LM2903YDT can generate a fault or control signal by comparing a feedback voltage with a reference level in motor-control and valve-position systems. Two channels allow complementary or independent limit checks within one package, while the 0.4 mA typical supply current is useful in compact power-constrained control electronics. The open-collector output can trigger an MCU input, a driver input, or a protection circuit through a pull-up. The design should account for electrical transients, common-mode limits, and propagation delay when determining whether the comparator can directly initiate a shutdown without additional filtering.
Recomendado
Battery Charger Overvoltage Protection
The LM2903YDT can supervise a charger or protected power rail by comparing a divided battery or output voltage against a reference. Its wide +2 V to +36 V single-supply operation allows the comparator to operate in elevated-voltage systems when the input network keeps the pins within their permitted common-mode range. Low typical input currents help preserve the accuracy of high-value dividers, and the two channels can monitor overvoltage and undervoltage conditions independently. Open-collector outputs permit wired fault signaling, provided the pull-up voltage remains compatible with the downstream logic and the fault node’s electrical limits.
Recomendado
Window Comparator for Precision Control
The two channels in the LM2903YDT can be configured as upper and lower thresholds to create a window comparator. This arrangement is useful when an analog signal must remain within a permitted band before an actuator, converter, or digital system is enabled. The rail-to-rail comparison capability supports signals extending toward the supply rails, and the open-collector outputs can be combined to produce a single in-range or out-of-range indication. Resistor matching and input bias current should be included in the threshold-error budget, while hysteresis can be added where the monitored signal crosses the limits slowly.
Recomendado
Embedded Control Signal Qualification
The LM2903YDT can qualify a noisy or slowly changing analog signal before it enters a microcontroller or programmable controller. A divided signal is compared with a reference, and the open-collector result provides a defined digital transition at the receiver. The low 0.4 mA supply current helps when the controller rail is always active, while the wide supply range provides flexibility across industrial and automotive systems. Choose the pull-up voltage for the receiving logic, keep the comparator input route short, and check whether the application requires a faster switching device than the LM2903 propagation characteristics can provide.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LM2903YDT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LM2903DT | LM2903Q2T | LM2903AVQDR |
|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Comparator Configuration | Dual differential comparator | Dual differential comparator | Dual differential comparator | Dual differential comparator |
| Output Type | Open collector | Open collector | Open collector | Open collector |
| Automotive Qualification Suffix | Y | Non-Y | Q2 | AVQ |
Principais diferenciais
- Automotive-oriented order suffix (vs LM2903DT)
- Low quiescent supply demand (vs LM2903Q2T)
- Very low input loading (vs LM2903AVQDR)
Notas de projeto
Do not treat an open-collector output as a push-pull logic output. Each channel requires a pull-up resistor, and multiple open-collector outputs may share one pull-up when wired-AND behavior is acceptable. Select the resistor using the receiver’s input thresholds and leakage, the required rise time, and the total capacitance of the connected traces. Omitting the pull-up leaves the output unable to establish a valid high state.
Keep comparator inputs short and connect them to a quiet reference ground. The typical 25 nA input bias current is small, but long PCB traces can introduce leakage and coupling that become significant with very high source impedances. If the input crosses a threshold slowly, add hysteresis to prevent output chatter and review propagation delay when defining the allowable transition time.
Place the supply bypass capacitor close to the device’s supply and ground pins, and provide a low-impedance ground return for both comparator channels. The open-collector pull-up should be positioned near the receiving circuit when the node is long or noisy. Maintain the SOIC-8 footprint and verify the pin assignment in the manufacturer datasheet before assigning nets, because schematic-library conventions can differ.
For automotive or industrial rails, distinguish the comparator’s +36 V maximum single-supply capability from the separate maximum input and differential-voltage ratings. Transient pulses, supply overshoot, and input common-mode excursions can violate the device limits even when the nominal rail is within range. Use the datasheet’s recommended protection network and validate it against the final source impedance and pulse profile.
Informações de conformidade
The manufacturer datasheet states that the device is qualified and characterized according to AEC Q100 and Q003 or equivalent, with advanced screening according to AEC Q001 and Q002 or equivalent. RoHS, REACH, lead-free, halogen-free, and conflict-minerals status were not explicitly established.