LPC2138FHN64 - 60MHz ARM7 MCU | NXP Semiconductors
N.º da peça: LPC2138FHN64 ✗ Fim de vidaLPC2138FHN64 Visão geral
An ARM7TDMI-S microcontroller is a 32-bit RISC processor for embedded control systems. The ARM7TDMI-S core belongs to the ARM architecture family and combines instruction execution with Thumb processing for code-density benefits. Within the product hierarchy, the LPC2138FHN64 is a microcontroller, an embedded semiconductor, and a programmable control device used to supervise sensors, actuators, communications, and real-time system functions.
The principal feature set includes 512 KB of embedded high-speed flash for program storage, 32 KB of on-chip SRAM, a 60 MHz maximum clock, and 47 general-purpose I/O ports. The serial interface set described for the LPC2131/32/34/36/38 family includes two I2C buses, two SPI interfaces, and UART capability. Analog signal acquisition and output are supported by 10-bit ADC and DAC channels, reducing the need for external converters in moderate-resolution systems.
The architecture combines an ARM7TDMI-S CPU with dedicated peripheral blocks and a 32-bit data bus. ISP and IAP support permits programming and in-application firmware operations, while real-time emulation and embedded trace support assist development and diagnostics. The 64-HVQFN footprint is intended for compact PCB layouts, but its exposed-pad construction requires careful thermal-via and copper design to transfer heat away from the device.
Typical uses include industrial control, embedded automation, IoT equipment, motor-control systems, metering instruments, and low-power board designs. In an automation controller, the MCU can combine sensor conversion through the ADC, actuator control through GPIO and timers, and local communications through I2C, SPI, and UART. In a metering product, the DAC can generate an analog output while the 512 KB flash stores calibration data, algorithms, and communication firmware.
Designers should preserve adequate input-voltage headroom across temperature, route the exposed thermal pad to a thermal-via array, and place decoupling capacitors close to the supply pins. Firmware replacement should follow the device's ISP or IAP procedures, and mixed-signal layouts should isolate analog inputs from high-current switching nodes to avoid measurement errors.
This product page combines the LPC2138FHN64 specifications, package information, lifecycle context, drop-in family alternatives, and application guidance into an engineering-focused reference for MCU selection, PCB implementation, firmware planning, and replacement assessment.
Alternativas drop-in para LPC2138FHN64 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
LPC2138FHN64/01
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LPC2138FHN64/01,55
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LPC2138FHN64,557
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LPC2148FHN64
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LPC2146FHN64
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LPC2144FHN64
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
LPC2138FHN64 Classificações máximas e características elétricas
| Product Type | Single-chip 16/32-bit microcontroller |
| Processor Core | ARM7TDMI-S RISC |
| Maximum Clock Speed | 60 MHz |
| Program Memory | 512 KB Flash (512K x 8) |
| Program Memory Type | ISP/IAP Flash |
| Data Memory | 32 KB SRAM (32K x 8) |
| Largura do barramento de dados | 8 bit |
| Tensão de alimentação de operação | 3.0 V to 3.6 V |
| ADC Resolution | 10 bit |
| ADC Channel Count | Up to 2 channels |
| DAC Resolution | 10 bit |
| I/O Port Count | 47 ports |
| I2C Interface Count | 2 interfaces |
| SPI Interface Count | 2 interfaces |
| Encapsulamento | 64-HVQFN |
| Tipo de montagem | Surface mount |
| Temperature Grade | Industrial |
| Development Support | Real-time emulation and embedded trace |
Guia de Configuração de Pinos do LPC2138FHN64 64-hvqfn
Configuração de pinos para LPC2138FHN64 (pacote 64-hvqfn). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para LPC2138FHN64.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
LPC2138FHN64 é adequado para 6 aplicaçãos: Industrial Automation Controller, IoT Sensor Gateway, Motor Control and Monitoring, Smart Metering Instrument, Industrial Communication Gateway, Low-Power Embedded Control Board.
Industrial Automation Controller
The LPC2138FHN64 fits an embedded automation controller because its 60 MHz ARM7TDMI-S core can execute sequencing and motion-control logic while 47 GPIO lines support discrete inputs, outputs, interlocks, and status signals. Two 10-bit ADC channels can sample analog process variables, while I2C and SPI provide local links to sensors, isolated transceivers, and data converters. Its 512 KB of ISP/IAP flash accommodates application firmware, field data, and update routines, and 32 KB of SRAM supports protocol buffers and control state. The practical benefit is consolidated real-time control without a separate processor, but the exposed HVQFN thermal pad must be connected to a via array and the analog inputs isolated from switching-node copper.
IoT Sensor Gateway
The LPC2138FHN64 can serve as the local control processor in an IoT sensor gateway by acquiring measurements through its 10-bit ADC and managing peripheral devices through two I2C and two SPI interfaces. UART connectivity supports a modem or low-speed service link, while 47 GPIO lines accommodate configuration straps, alarm outputs, and interface-enable signals. The 512 KB flash supports gateways requiring local buffering, protocol translation, or OTA-related firmware logic, and the 60 MHz ARM7TDMI-S core leaves headroom for multiple concurrent communication tasks. Designers should use ISP or IAP for controlled firmware updates and should verify boot pins, reset behavior, and the complete 64-pin assignment before adapting an existing gateway PCB.
Motor Control and Monitoring
The LPC2138FHN64 is suited to supervisory motor-control systems where a 60 MHz control core, two 10-bit ADCs, 47 GPIO ports, and multiple timer-driven interfaces are useful for managing drive commands and diagnostics. The MCU can monitor analog feedback, operate interlocks, communicate with a power stage, and record operating conditions through UART, SPI, or I2C. Its 512 KB flash is useful for stored control tables and diagnostic logic, while 32 KB of SRAM supports state machines and communication buffers. This is not a substitute for a dedicated high-performance motor-control IC; validate PWM resolution, timer mapping, fault-response latency, and electrical isolation against the motor-drive architecture before connecting power electronics.
Smart Metering Instrument
The LPC2138FHN64 fits metering instruments that need local signal acquisition, calibration storage, and a reliable communications path in a compact package. Its two 10-bit ADCs can digitize moderate-resolution sensor inputs, and the 10-bit DAC can support excitation, reference, or test-signal generation. The 512 KB flash provides room for measurement algorithms, calibration coefficients, event logs, and communications firmware, while 32 KB of SRAM can buffer sampled data. I2C and SPI permit connection to display, memory, or transceiver ICs, while UART supports a service port. For regulatory metering, verify ADC accuracy, oscillator tolerance, reset behavior, and calibration-data retention requirements independently of these general-purpose specifications.
Industrial Communication Gateway
The LPC2138FHN64 can act as a protocol-conversion or field-bus gateway because the ARM7TDMI-S core runs at 60 MHz and the device combines 32 KB of SRAM, 47 GPIO ports, two UART-capable serial options, I2C, and SPI. Engineers can allocate one interface to a local bus, another to an upstream link, and use GPIO for protocol-select and fault lines. Its 512 KB ISP/IAP flash supports gateway configuration, logging code, and field upgrades, while the 64-HVQFN package reduces board area in compact equipment. A production design should check interrupt latency, buffer depth, connector electrical levels, watchdog behavior, and peripheral pin reuse because the controller does not automatically solve bus isolation or level translation.
Low-Power Embedded Control Board
The LPC2138FHN64 is appropriate for compact embedded control boards that require substantial local program storage without a higher-complexity application processor. Its 512 KB flash and 32 KB SRAM allow standalone control, logging, and communication firmware, while the 60 MHz ARM7TDMI-S core handles time-sensitive tasks and the 47 GPIO lines support sensors, relays, indicators, and interlocks. The 64-HVQFN footprint supports dense layouts, but exposed-pad heat spreading becomes important whenever switching activity or regulated peripherals raise dissipation. Firmware should use the device’s low-power modes, watchdog, reset controls, and brownout behavior where applicable, and the final power budget should include both active and sleep-state consumption.
Dados de referência de engenharia para LPC2138FHN64 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LPC2138FHN64/01 | LPC2138FHN64/01,55 | LPC2138FHN64,557 | LPC2148FHN64 | LPC2146FHN64 |
|---|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 64-HVQFN | 64-HVQFN | 64-HVQFN | 64-HVQFN | 64-HVQFN | 64-HVQFN |
| Processor Core | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S | ARM7TDMI-S |
| Maximum Clock Speed | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz | 60 MHz |
| Program Memory | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB |
Principais diferenciais
- High flash capacity within the LPC21xx family (vs LPC2146FHN64)
- Direct ordering compatibility with the revised /01 designation (vs LPC2138FHN64/01)
- Broader GPIO availability for embedded control (vs LPC2148FHN64)
- Mixed-signal integration reduces external converter count (vs LPC2144FHN64)
Notas de projeto
Treat the HVQFN exposed pad as a thermal and electrical construction feature, not as an optional thermal area. Connect it to the ground plane through multiple vias and provide uninterrupted copper beneath the device. Estimated: with a junction-to-ambient thermal resistance of 30 C/W, 250 mW of dissipation produces about 7.5 C junction-temperature rise; actual resistance depends on board size, copper, vias, and ambient conditions. Recalculate with the PCB implementation used in the final product.
Place the supply bypass capacitors close to the corresponding VDD pins and keep the high-current return path short. Separate analog inputs from digital clocks, UART activity, and switching-power routing, and provide a quiet return path for the ADC and DAC reference network. The 64-HVQFN footprint has fine-pitch leads, so inspect the manufacturer land pattern for pad dimensions, solder-mask clearance, and exposed-pad paste volume before releasing artwork.
Do not assume that every 64-HVQFN LPC21xx controller is electrically interchangeable. Verify boot-mode pins, reset polarity, oscillator connections, debug signals, analog pins, communication assignments, and exposed-pad connections against the exact datasheet. Software migration also requires checks to peripheral addresses, interrupt vectors, register definitions, and driver support. A package drawing match is necessary for PCB reuse but is not sufficient to approve a drop-in replacement.
Design the 3.0 V to 3.6 V supply rail with transient margin for startup and peripheral load, and verify brownout behavior against the minimum voltage required by the firmware. The 60 MHz CPU and switched I/O can create fast current edges, so use a low-impedance distribution path and local high-frequency decoupling. For battery-powered products, calculate average current from processor active time, peripheral duty cycle, and sleep duration rather than using only the maximum operating frequency.
Informações de conformidade
The NXP product information identifies an industrial-grade microcontroller but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable to the standard industrial LPC2138FHN64 ordering designation.