LTC1545CG - 5/5 Multiprotocol Transceiver | Analog Devices
N.º da peça: LTC1545CG ✓ AtivoLTC1545CG Visão geral
A multiprotocol transceiver is an interface IC that combines drivers, receivers, and selectable termination or biasing functions so a data-communications port can operate with different electrical standards. The LTC1545CG provides five balanced driver channels and five receiver channels, allowing simultaneous control-signal and data-path operation in DTE or DCE port designs. Protocol selection is handled in software rather than through a permanently fixed physical interface.
Key features include five drivers, five receivers, support for seven named serial protocols, and software-selectable cable termination. The manufacturer identifies the LTC1545 as production-available and presents it together with the LTC1543 as the core of a complete software-selectable DTE or DCE interface port. Termination can alternatively be implemented with the LTC1344A software-selectable cable-termination circuit or with discrete networks.
Architecturally, the LTC1545 combines protocol-specific driver and receiver functions with control logic that configures the interface operating mode. This allows a single transceiver to serve equipment that must communicate with legacy RS-232, V.35, V.36, X.21, RS-449, or EIA-530 systems. The 36-lead SSOP provides enough external connections for driver outputs, receiver inputs, control inputs, and protocol-configuration signals while remaining compatible with established surface-mount assembly practices.
Typical uses include multiprotocol network-interface cards, industrial data collectors, legacy telecommunications equipment, test systems, and DTE or DCE port designs. In each case, the transceiver simplifies inventory by replacing several protocol-specific interface ICs. Software-controlled configuration also allows the same controller and driver architecture to be reused across different installed-base environments.
When designing a board around the LTC1545CG, confirm the exact protocol, connector assignment, termination requirement, and driver or receiver enable strategy against the pin-description table in the manufacturer datasheet. Leave filtering and protection to the external signal-chain components recommended for the selected protocol, and verify board-level timing and grounding against the equipment's EMC requirements.
This page consolidates protocol coverage, package information, drop-in sourcing options, application guidance, and design cautions into one engineering reference. It also distinguishes verified device attributes from parameters that must be confirmed in the full datasheet before schematic capture or production release.
Alternativas drop-in para LTC1545CG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
LTC1545CG#PBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC1545CG Especificações
| Product Type | Software-selectable multiprotocol transceiver |
| Driver Count | 5 drivers |
| Receiver Count | 5 receivers |
| Supported Protocol 1 | RS-232 |
| Supported Protocol 2 | RS-449 |
| Supported Protocol 3 | EIA-530 |
| Supported Protocol 4 | EIA-530-A |
| Supported Protocol 5 | V.35 |
| Supported Protocol 6 | V.36 |
| Supported Protocol 7 | X.21 |
| Cable Termination | Software-selectable |
| Port Configuration | Software-selectable DTE or DCE |
| Number of Terminals | 36 terminals |
| Package Type | SSOP-36, gull wing |
| Package Shape | Rectangular |
| Temperature Grade | Commercial |
| Tipo de montagem | Surface mount |
| External Cable Termination Companion | LTC1344A |
| Related Port Controller | LTC1543 |
Guia de Configuração de Pinos do LTC1545CG rectangular
Configuração de pinos para LTC1545CG (pacote rectangular). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para LTC1545CG.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
LTC1545CG é adequado para 6 aplicaçãos: Software-Selectable DTE Interface Port, Software-Selectable DCE Interface Port, Legacy Network Interface Card, Industrial Data Collection Terminal, Telecommunications Test Equipment, Protocol-Aware Data Concentrator.
Software-Selectable DTE Interface Port
The LTC1545CG fits a DTE port that must communicate through RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, or X.21. Its five drivers and five receivers provide parallel signal-conditioning resources within one 36-lead SSOP. Software-controlled protocol selection lets the host controller change operating modes without replacing the physical interface board. The design should follow the manufacturer terminal table for driver and receiver enable routing.
Recomendado
Software-Selectable DCE Interface Port
A DCE product can use the LTC1545CG as the protocol-facing transceiver while the associated controller manages software operation. Supporting seven legacy serial protocols from one 36-terminal SSOP reduces board variants and field-inventory complexity. The approach is useful for telecommunications equipment whose customers may connect equipment using different legacy standards. Confirm connector mapping and per-protocol enable sequencing before finalizing the PCB.
Recomendado
Legacy Network Interface Card
The LTC1545CG is suitable for a multiprotocol network-interface card that must bridge legacy serial protocols to a host controller. Five drivers and five receivers support multiple signal paths within the card, and software selection allows one connector strategy to serve RS-232, V.35, V.36, X.21, RS-449, EIA-530, or EIA-530-A equipment. Board-level layout must preserve the return paths and shielding required by the selected protocol.
Recomendado
Industrial Data Collection Terminal
Industrial terminals that connect to older supervisory, instrumentation, or plant-network equipment benefit from the LTC1545CG’s software-selectable protocol support. One 36-lead SSOP can replace multiple dedicated serial-interface circuits while maintaining five transmit and five receive channels. The design remains appropriate where field equipment spans several generations of electrical interfaces. Use the manufacturer application guidance for protection, grounding, and protocol-specific filtering.
Recomendado
Telecommunications Test Equipment
Test equipment can use the LTC1545CG to emulate or exercise several legacy DTE or DCE ports with one transceiver circuit. Software selection among RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21 reduces the number of interchangeable interface modules needed in a laboratory. The device is particularly useful where test systems must verify equipment against multiple installed-base standards. Calibration and stimulus design remain separate from the transceiver interface.
Recomendado
Protocol-Aware Data Concentrator
A data concentrator serving equipment with mixed legacy interfaces can place the LTC1545CG on each protocol-configurable port. Five drivers and five receivers permit multiple signal paths, while software-controlled termination can adapt the port when the selected standard changes. This supports consolidation of legacy serial links without maintaining separate transceiver boards for each protocol. Verify enable timing, signal levels, and connector assignments for every supported mode.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LTC1545CG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LTC1545CG#PBF |
|---|---|---|
| Brand | Analog Devices | Analog Devices |
| Package | SSOP-36 | SSOP-36 - same footprint |
| Function | Software-selectable multiprotocol transceiver | Same LTC1545 transceiver function |
| Driver Count | 5 drivers | 5 drivers |
| Receiver Count | 5 receivers | 5 receivers |
| Supported Protocols | RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, X.21 | RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, X.21 |
| Cable Termination | Software-selectable | Software-selectable |
| Port Role | Software-selectable DTE or DCE port core | Software-selectable DTE or DCE port core |
| Temperature Grade | Commercial | Commercial device family |
| Terminal Count | 36 terminals | 36 terminals |
Principais diferenciais
- Seven legacy protocols in one transceiver (vs LTC1545CG#PBF)
- Higher channel count than a basic single-protocol interface (vs LTC1543)
- Selectable termination architecture (vs Discrete termination networks)
Notas de projeto
Route each driver output and receiver input according to the selected protocol rather than treating the LTC1545CG as a generic RS-232 device. Keep return paths short and preserve the ground-reference arrangement shown in the manufacturer application guidance. Because one package supports RS-232, V.35, V.36, X.21, RS-449, EIA-530, and EIA-530-A, unused channels and mode-dependent nodes still require deliberate PCB treatment.
Verify driver and receiver enable sequencing for the protocol being activated so channels do not contend during mode changes. The LTC1545CG provides five drivers and five receivers with software-selectable operation, so control sequencing is a functional part of the interface rather than a minor firmware detail. Use the terminal table and timing information in the manufacturer data sheet to establish safe transitions between protocols.
Do not assume that the LTC1543 can replace the LTC1545CG. The LTC1543 is the associated port controller, while the LTC1545CG is the 5-driver, 5-receiver transceiver. Likewise, verify whether a selected ordering suffix denotes a lead-free finish or tape-and-reel packaging before treating it as a distinct electrical device. Maintain consistent package orientation and terminal numbering during assembly.
Informações de conformidade
The commercial-grade LTC1545CG is a general-purpose interface IC rather than an automotive-qualified product. The lead-free #PBF ordering option is listed by Analog Devices, but no explicit RoHS, REACH, or halogen-free declaration was established for the base ordering code.