Analog Devices

LTC1545CG - 5/5 Multiprotocol Transceiver | Analog Devices

MPN: LTC1545CG ✓ 啟用中
SSOP-36, gull wing Package
MOQ: 1 |

LTC1545CG 概覽

The Analog Devices LTC1545CG is a software-selectable 5-driver, 5-receiver multiprotocol transceiver for RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21 interfaces. It is supplied in a 36-lead SSOP package and is intended for commercial-grade communications equipment requiring one physical design to cover several legacy serial protocols.

A multiprotocol transceiver is an interface IC that combines drivers, receivers, and selectable termination or biasing functions so a data-communications port can operate with different electrical standards. The LTC1545CG provides five balanced driver channels and five receiver channels, allowing simultaneous control-signal and data-path operation in DTE or DCE port designs. Protocol selection is handled in software rather than through a permanently fixed physical interface.

Key features include five drivers, five receivers, support for seven named serial protocols, and software-selectable cable termination. The manufacturer identifies the LTC1545 as production-available and presents it together with the LTC1543 as the core of a complete software-selectable DTE or DCE interface port. Termination can alternatively be implemented with the LTC1344A software-selectable cable-termination circuit or with discrete networks.

Architecturally, the LTC1545 combines protocol-specific driver and receiver functions with control logic that configures the interface operating mode. This allows a single transceiver to serve equipment that must communicate with legacy RS-232, V.35, V.36, X.21, RS-449, or EIA-530 systems. The 36-lead SSOP provides enough external connections for driver outputs, receiver inputs, control inputs, and protocol-configuration signals while remaining compatible with established surface-mount assembly practices.

Typical uses include multiprotocol network-interface cards, industrial data collectors, legacy telecommunications equipment, test systems, and DTE or DCE port designs. In each case, the transceiver simplifies inventory by replacing several protocol-specific interface ICs. Software-controlled configuration also allows the same controller and driver architecture to be reused across different installed-base environments.

When designing a board around the LTC1545CG, confirm the exact protocol, connector assignment, termination requirement, and driver or receiver enable strategy against the pin-description table in the manufacturer datasheet. Leave filtering and protection to the external signal-chain components recommended for the selected protocol, and verify board-level timing and grounding against the equipment's EMC requirements.

This page consolidates protocol coverage, package information, drop-in sourcing options, application guidance, and design cautions into one engineering reference. It also distinguishes verified device attributes from parameters that must be confirmed in the full datasheet before schematic capture or production release.

直接替換替代品,適用於 LTC1545CG — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

LTC1545CG#PBF

✅ 直接替換
📦 SSOP-36
Same LTC1545 5-driver, 5-receiver transceiver and 36-lead SSOP footprint; ordering suffix specifies the lead-free finish rather than a different protocol set.

📋 參考替代品(不在目錄中)

LTC1545CG 規格

Product Type Software-selectable multiprotocol transceiver
Driver Count 5 drivers
Receiver Count 5 receivers
Supported Protocol 1 RS-232
Supported Protocol 2 RS-449
Supported Protocol 3 EIA-530
Supported Protocol 4 EIA-530-A
Supported Protocol 5 V.35
Supported Protocol 6 V.36
Supported Protocol 7 X.21
Cable Termination Software-selectable
Port Configuration Software-selectable DTE or DCE
Number of Terminals 36 terminals
Package Type SSOP-36, gull wing
Package Shape Rectangular
Temperature Grade Commercial
安裝類型 Surface mount
External Cable Termination Companion LTC1344A
Related Port Controller LTC1543

LTC1545CG rectangular 腳位配置指南

LTC1545CG(rectangular 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

LTC1545CG 的 rectangular 封裝腳位圖

無詳細腳位定義資料: LTC1545CG.

請參閱 資料表 以查看完整腳位配置。

典型應用

LTC1545CG 適用於 6 應用s: Software-Selectable DTE Interface Port, Software-Selectable DCE Interface Port, Legacy Network Interface Card, Industrial Data Collection Terminal, Telecommunications Test Equipment, Protocol-Aware Data Concentrator.

🌐

Software-Selectable DTE Interface Port

The LTC1545CG fits a DTE port that must communicate through RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, or X.21. Its five drivers and five receivers provide parallel signal-conditioning resources within one 36-lead SSOP. Software-controlled protocol selection lets the host controller change operating modes without replacing the physical interface board. The design should follow the manufacturer terminal table for driver and receiver enable routing.

🌐

Software-Selectable DCE Interface Port

A DCE product can use the LTC1545CG as the protocol-facing transceiver while the associated controller manages software operation. Supporting seven legacy serial protocols from one 36-terminal SSOP reduces board variants and field-inventory complexity. The approach is useful for telecommunications equipment whose customers may connect equipment using different legacy standards. Confirm connector mapping and per-protocol enable sequencing before finalizing the PCB.

🖥️

Legacy Network Interface Card

The LTC1545CG is suitable for a multiprotocol network-interface card that must bridge legacy serial protocols to a host controller. Five drivers and five receivers support multiple signal paths within the card, and software selection allows one connector strategy to serve RS-232, V.35, V.36, X.21, RS-449, EIA-530, or EIA-530-A equipment. Board-level layout must preserve the return paths and shielding required by the selected protocol.

🏭

Industrial Data Collection Terminal

Industrial terminals that connect to older supervisory, instrumentation, or plant-network equipment benefit from the LTC1545CG’s software-selectable protocol support. One 36-lead SSOP can replace multiple dedicated serial-interface circuits while maintaining five transmit and five receive channels. The design remains appropriate where field equipment spans several generations of electrical interfaces. Use the manufacturer application guidance for protection, grounding, and protocol-specific filtering.

📡

Telecommunications Test Equipment

Test equipment can use the LTC1545CG to emulate or exercise several legacy DTE or DCE ports with one transceiver circuit. Software selection among RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21 reduces the number of interchangeable interface modules needed in a laboratory. The device is particularly useful where test systems must verify equipment against multiple installed-base standards. Calibration and stimulus design remain separate from the transceiver interface.

🔀

Protocol-Aware Data Concentrator

A data concentrator serving equipment with mixed legacy interfaces can place the LTC1545CG on each protocol-configurable port. Five drivers and five receivers permit multiple signal paths, while software-controlled termination can adapt the port when the selected standard changes. This supports consolidation of legacy serial links without maintaining separate transceiver boards for each protocol. Verify enable timing, signal levels, and connector assignments for every supported mode.

推薦產品摘要

LTC1543 Associated port controller 用於: Software-Selectable DTE Interface Port, Software-Selectable DCE Interface Port, Legacy Network Interface Card, Industrial Data Collection Terminal, Telecommunications Test Equipment, Protocol-Aware Data Concentrator LTC1545CG#PBF Lead-free ordering option 用於: Software-Selectable DTE Interface Port LTC1344A Software-selectable cable termination 用於: Software-Selectable DCE Interface Port, Legacy Network Interface Card, Industrial Data Collection Terminal, Telecommunications Test Equipment, Protocol-Aware Data Concentrator
What is the LTC1545CG used for?
The LTC1545CG is a software-selectable multiprotocol transceiver used to implement legacy serial interface ports. It combines five drivers and five receivers in one 36-lead SSOP and supports RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21. Analog Devices describes the LTC1545 and LTC1543 as the core of a complete software-selectable DTE or DCE interface port.
Which protocols does the LTC1545CG support?
The LTC1545CG supports RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21 serial protocols. According to the Analog Devices LTC1545 product page, protocol selection is performed in software. This lets one transceiver design cover several DTE and DCE port configurations without changing to a separate physical interface circuit for each standard.
How many drivers and receivers does the LTC1545CG contain?
The LTC1545CG contains five drivers and five receivers. These ten signal-conditioning channels support a multiprotocol interface rather than the smaller channel count of a basic RS-232 or RS-485 transceiver. The manufacturer product page identifies the device as a 5-driver, 5-receiver multiprotocol transceiver for software-selectable DTE or DCE implementations.
Is the LTC1545CG a drop-in replacement for LTC1545CG#PBF?
The LTC1545CG and LTC1545CG#PBF identify the same LTC1545 device in a 36-lead SSOP, with the #PBF ordering code indicating the lead-free finish rather than a different transceiver function. The LTC1545CG#PBF listing identifies the package as SSOP-36. Confirm the exact orderable suffix and terminal orientation on your purchase documentation before treating the two markings as interchangeable.
Where can I download the LTC1545CG datasheet PDF?
The official LTC1545 documentation is available from the Analog Devices product page at https://www.analog.com/en/products/ltc1545.html, where the manufacturer provides the LTC1545 data sheet and supporting documentation. Use the manufacturer document for the terminal table, electrical characteristics, protocol timing, and recommended application circuit. The LTC1545CG is the commercial-grade 36-terminal SSOP ordering option.
Where is the LTC1545CG pinout located?
The LTC1545CG pinout is documented in the pin-configuration and terminal-information sections of the Analog Devices LTC1545 data sheet. The device is specified in a 36-lead rectangular SSOP with gull-wing terminals and a commercial temperature grade. Use that table for signal assignment, especially protocol-control inputs, driver enables, receiver enables, and termination-related connections.
What is the difference between the LTC1545 and LTC1543?
The LTC1545 is the 5-driver, 5-receiver multiprotocol transceiver, while the LTC1543 serves as the associated port controller in a complete software-selectable DTE or DCE interface. Analog Devices describes the two devices together as the core of a complete port implementation. The LTC1543 is a functional companion rather than a pin-compatible drop-in replacement for the LTC1545CG.
Can the LTC1344A be used with the LTC1545CG for cable termination?
Yes, the LTC1344A can be used for software-selectable cable termination with the LTC1545. The Analog Devices LTC1545 product page states that termination may be implemented with the LTC1344A or with existing discrete designs. This is especially useful when a product must switch termination requirements as its interface protocol changes, and it helps avoid a separate discrete termination network.
When should I choose the LTC1545CG instead of a single-protocol RS-232 transceiver?
Choose the LTC1545CG when one product must support several legacy serial standards under software control. A single-protocol RS-232 transceiver is simpler for a fixed RS-232-only design, but the LTC1545CG supports RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21 through one 36-lead SSOP. The trade-off is a larger pin count and more complex configuration logic.
What can replace the LTC1545CG?
The closest documented drop-in option is the LTC1545CG#PBF ordering code, which uses the same 36-lead SSOP transceiver configuration with a lead-free finish. The LTC1543 is not a replacement because it is the port-controller companion rather than the 5-driver, 5-receiver transceiver. No other manufacturer’s pin-compatible, SSOP-36 multiprotocol equivalent was established, so board changes should not be assumed.
Is the LTC1545CG the same as the LTC1545CG#TR?
No, LTC1545CG#TR is a tape-and-reel ordering option rather than a different functional transceiver. The DigiKey listing identifies LTC1545CG#TR as an Analog Devices 5/3 multiprotocol transceiver in a 36-lead SSOP, while the #PBF code denotes a lead-free package treatment. Both ordering codes should be checked against the LTC1545CG device function and 36-terminal package requirements.
Is the LTC1545CG still in production?
Yes, Analog Devices identifies the LTC1545 as production in the official product-page overview. The device is therefore presented as an active product family, although order-code suffixes such as #PBF and #TR denote different packaging or lead-free specifications. Confirm current commercial availability, minimum order quantity, and lead time through the Request a Quote form on this page.
Where can I buy the LTC1545CG online?
The LTC1545CG can be requested through the Request a Quote form on this XAIPART page. The manufacturer product page supports sample and buy activity, and distributor listings identify the part in 36-lead SSOP form. A quote request should include the required order code, quantity, and lead-time target so current commercial terms can be confirmed.
What is the price of the LTC1545CG?
Current commercial pricing for the LTC1545CG depends on order code, quantity, and supplier terms. Use the Request a Quote form on this page to request a current quotation for the exact ordering suffix and volume. The manufacturer product page also links to sample and buy options for evaluation, while authorized distributor listings can confirm market availability.
What is the lead time for the LTC1545CG?
The LTC1545CG lead time depends on the selected ordering suffix and current manufacturer or distributor inventory. Analog Devices lists the LTC1545 as production, but production status alone does not guarantee immediate availability. Submit the exact MPN, required quantity, and target date through the Request a Quote form on this page for current scheduling information.
Is the LTC1545CG in stock?
Stock status for the LTC1545CG varies by order code and distribution channel, so it should not be inferred from the existence of a product listing. The official Analog Devices overview identifies the family as production, and distributor records cover multiple orderable variants. Use the Request a Quote form on this page to check current availability for your required suffix and quantity.
What are the key specifications of LTC1545CG engineers should know?
The key LTC1545CG specifications are 5 drivers, 5 receivers, software-selectable operation across RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21, and a 36-terminal commercial-grade SSOP package. According to the Analog Devices LTC1545 product page, the device forms the transceiver half of a software-selectable DTE or DCE port and supports software-controlled cable termination.

工程參考資料,適用於 LTC1545CG — 比較、設計指引及合規資訊。

選型指南

Choose the LTC1545CG when a product must present a software-programmable DTE or DCE port spanning RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, and X.21. Its five drivers, five receivers, and selectable termination functions consolidate several legacy interfaces into one 36-lead SSOP design. Use the LTC1543 as the associated port controller and the LTC1344A when a dedicated software-selectable termination circuit is appropriate. A single-protocol RS-232 transceiver remains preferable for a fixed, low-channel-count interface because it usually requires fewer pins and simpler control logic. For sourcing, LTC1545CG#PBF is the documented lead-finish ordering option of the same device, but procurement should confirm the exact suffix, quantity, and commercial terms. Do not select the LTC1543 as a direct substitute because its function and terminal arrangement differ.

與替代品比較

參數 本產品 LTC1545CG#PBF
Brand Analog Devices Analog Devices
Package SSOP-36 SSOP-36 - same footprint
Function Software-selectable multiprotocol transceiver Same LTC1545 transceiver function
Driver Count 5 drivers 5 drivers
Receiver Count 5 receivers 5 receivers
Supported Protocols RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, X.21 RS-232, RS-449, EIA-530, EIA-530-A, V.35, V.36, X.21
Cable Termination Software-selectable Software-selectable
Port Role Software-selectable DTE or DCE port core Software-selectable DTE or DCE port core
Temperature Grade Commercial Commercial device family
Terminal Count 36 terminals 36 terminals

主要差異化特點

  • Seven legacy protocols in one transceiver (對比LTC1545CG#PBF)
  • Higher channel count than a basic single-protocol interface (對比LTC1543)
  • Selectable termination architecture (對比Discrete termination networks)

設計說明

Route each driver output and receiver input according to the selected protocol rather than treating the LTC1545CG as a generic RS-232 device. Keep return paths short and preserve the ground-reference arrangement shown in the manufacturer application guidance. Because one package supports RS-232, V.35, V.36, X.21, RS-449, EIA-530, and EIA-530-A, unused channels and mode-dependent nodes still require deliberate PCB treatment.

Verify driver and receiver enable sequencing for the protocol being activated so channels do not contend during mode changes. The LTC1545CG provides five drivers and five receivers with software-selectable operation, so control sequencing is a functional part of the interface rather than a minor firmware detail. Use the terminal table and timing information in the manufacturer data sheet to establish safe transitions between protocols.

Do not assume that the LTC1543 can replace the LTC1545CG. The LTC1543 is the associated port controller, while the LTC1545CG is the 5-driver, 5-receiver transceiver. Likewise, verify whether a selected ordering suffix denotes a lead-free finish or tape-and-reel packaging before treating it as a distinct electrical device. Maintain consistent package orientation and terminal numbering during assembly.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The commercial-grade LTC1545CG is a general-purpose interface IC rather than an automotive-qualified product. The lead-free #PBF ordering option is listed by Analog Devices, but no explicit RoHS, REACH, or halogen-free declaration was established for the base ordering code.

資料驗證日期: 2026-11-09 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

LTC1545CG datasheet LTC1545CG datasheet pdf LTC1545CG pinout LTC1545CG SSOP-36 transceiver LTC1545CG supported protocols LTC1545CG vs LTC1543 LTC1545CG drop-in replacement LTC1545CG equivalent transceiver Analog Devices LTC1545CG LTC1545CG software selectable DTE DCE LTC1545CG price LTC1545CG stock what is LTC1545CG used for LTC1545CG application circuit

相關元件與詞彙

Analog Devices LTC1545CG LTC1545CG#PBF LTC1543 LTC1344A multiprotocol transceiver interface IC line transceiver DTE interface DCE interface RS-232 RS-449 EIA-530 EIA-530-A V.35 V.36 X.21 software-selectable cable termination SSOP-36 gull-wing terminal surface-mount package commercial temperature grade RS-232 interface IC data-communications port
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情