LTC7806JUFDM#WPBF - 40V, 3MHz 2-Phase Synchronous Boost Controller | ADI
N.º da peça: LTC7806JUFDM#WPBF ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $6.18 | $6,18 |
| 10 | $5.61 | $56,10 |
| 100 | $4.99 | $499,00 |
| 500 | $4.42 | $2.210,00 |
| 1.000 | $3.92 | $3.920,00 |
LTC7806JUFDM#WPBF Visão geral
What is a boost controller? A boost (step-up) controller is a type of DC-DC switching controller that uses an external inductor and power switches to produce an output voltage higher than the input. The LTC7806 is a controller-only IC (no internal MOSFETs), so it drives external N-channel MOSFETs, allowing designers to scale output current by selecting MOSFETs of any desired Rds(on). It belongs to the hierarchy: boost controller -> DC-DC switching controller -> switching regulator -> power management IC -> semiconductor.
Key features include 2-phase synchronous operation up to 3MHz switching frequency, 4.5V to 40V input range, output up to 36V, low quiescent current, robust overcurrent protection for safe startup, and AEC-Q100 screening for automotive designs. Synchronous rectification increases efficiency and reduces power losses compared to asynchronous boost designs. High-frequency 2-phase operation reduces input and output capacitor requirements and allows smaller inductors than the single-phase equivalent.
The 2-phase architecture interleaves clock phases to cancel input ripple current, reducing RMS stress on the input capacitor and EMI filter. The exposed pad (EP) of the 4mm x 5mm QFN-28 package provides a low thermal resistance path (theta_JC of about 3 C/W), enabling high-power automotive boost applications up to tens of amps.
Typical applications include automotive pre-boost supplies for audio amplifiers, LED drivers and headlight electronics, industrial 24V-to-36V bus converters, battery-powered systems requiring step-up conversion, point-of-load (POL) converters in distributed power architectures, and emergency/backup power where wide input transients are common. The J-grade +150C operating range supports under-hood automotive placements.
When designing with this part, follow the datasheet guidance on output current sense resistor selection, soft-start capacitor sizing, and minimum on/off-time constraints. The exposed pad must be soldered to a sufficient copper pour (typically >= 1 sq inch on top + thermal via array to inner/outer planes) to keep junction temperature within the +150C maximum under worst-case load.
Alternativas drop-in para LTC7806JUFDM#WPBF — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
LTC7806IUFDM#WPBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC7806JUFDM#WTRPBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC7806IUFDM#WTRPBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC7806RUFDM#PBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LT3576EUFE-1#TRPBF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
LTC7806JUFDM#WPBF Classificações máximas e características elétricas
| Topologia | Boost (Step-Up) Controller |
| Número de saídas | 1 |
| Faixa de tensão de entrada | 4.5 V to 40 V |
| Tensão de saída | Up to 36 V |
| Maximum Switching Frequency | 3 MHz |
| Number of Phases | 2 (synchronous, interleaved) |
| Retificação síncrona | Yes (drives external N-MOSFET) |
| Faixa de temperatura de operação | -40 C to +150 C (junction, J grade) |
| Package Type | 28-Lead (4 mm x 5 mm) Plastic QFN with Exposed Pad |
| Tipo de montagem | Surface Mount |
| AEC-Q100 Qualification | Qualified |
| Status RoHS | Compliant (Pb-free PBF suffix) |
| Lead-Free | Yes (PBF suffix) |
| Factory Pack Quantity | Tube (WPBF suffix per product family convention) |
Configuração de pinos do LTC7806JUFDM#WPBF
| Pino 1 | VIN — Main input supply; decouple to PGND with ceramic capacitor |
| Pino 2 | VOUT — Boost output sense (controller monitors VOUT for regulation) |
| Pino 3 | BST1 — Phase-1 boost capacitor node for top gate driver supply |
| Pino 4 | TG1 — Phase-1 top gate drive (drives synchronous N-MOSFET) |
| Pino 5 | SW1 — Phase-1 switching node (between external L and synchronous FET) |
| Pino 6 | BG1 — Phase-1 bottom gate drive (drives synchronous N-MOSFET) |
| Pino 7 | PGND1 — Phase-1 power ground return |
| Pino 8 | SENSE1+ — Phase-1 current sense positive input (across sense resistor) |
| Pino 9 | SENSE1- — Phase-1 current sense negative input |
| Pino 10 | FREQ — Frequency set resistor to ground (programs switching frequency) |
| Pino 11 | RT — Timing resistor (sets oscillator frequency) |
| Pino 12 | SS — Soft-start programming capacitor |
| Pino 13 | VREF — Internal reference bypass capacitor |
| Pino 14 | ITH — Compensation node for the error amplifier |
| Pino 15 | VFB — Voltage feedback input (external resistor divider sets VOUT) |
| Pino 16 | RUN — Run/enable input (UVLO threshold) |
| Pino 17 | PGOOD — Power good open-drain output |
| Pino 18 | INTVCC — Internal 5V LDO output for gate drive supply |
| Pino 19 | BST2 — Phase-2 boost capacitor node for top gate driver supply |
| Pino 20 | TG2 — Phase-2 top gate drive (drives synchronous N-MOSFET) |
| Pino 21 | SW2 — Phase-2 switching node (between external L and synchronous FET) |
| Pino 22 | BG2 — Phase-2 bottom gate drive (drives synchronous N-MOSFET) |
| Pino 23 | PGND2 — Phase-2 power ground return |
| Pino 24 | SENSE2+ — Phase-2 current sense positive input |
| Pino 25 | SENSE2- — Phase-2 current sense negative input |
| Pino 26 | CLKOUT — Phase-clock output for cascaded multi-phase applications |
| Pino 27 | MODE — Mode selection (pulse-skipping / forced-continuous / Burst Mode) |
| Pino 28 | SYNC — External clock synchronization input |
Aplicações típicas
LTC7806JUFDM#WPBF é adequado para 6 aplicaçãos: Automotive Pre-Boost Supply for Audio Amplifiers, Automotive LED Headlight Driver Front-End, Industrial 24V-to-36V Bus Converter, Battery-Backed Emergency Power Pre-Regulator, Point-of-Load Front-End in Distributed Power, ADAS Sensor Power Conditioning.
Automotive Pre-Boost Supply for Audio Amplifiers
The LTC7806JUFDM#WPBF is well suited to step up a 12V automotive battery rail to a 24V or 36V intermediate bus that feeds Class-D audio amplifiers. The controller's 4.5V to 40V input range tolerates load-dump transients up to 40V, and the 2-phase 3 MHz architecture minimizes input ripple current that would otherwise inject audible noise into the audio chain. J-grade +150C junction rating supports under-hood or amplifier heat-sink adjacent placements common in high-power infotainment systems.
Recomendado
Automotive LED Headlight Driver Front-End
In adaptive LED headlight modules, the LTC7806JUFDM#WPBF boosts the 12V battery rail to a stable 30V to 36V bus that powers downstream LED driver ICs and switching converters. The AEC-Q100 automotive screening and J-grade +150C temperature rating match the harsh thermal environment inside headlamp assemblies. The exposed-pad QFN-28 package provides low theta_JC for reliable operation at high boost duty cycles when input voltage dips during cranking.
Recomendado
Industrial 24V-to-36V Bus Converter
Industrial 24V factory bus systems often need a 36V rail to feed downstream buck regulators, motor pre-drivers, or sensor excitation supplies. The LTC7806JUFDM#WPBF handles 24V nominal inputs with margin up to 40V and produces up to 36V output with high efficiency thanks to synchronous rectification. The 3 MHz switching frequency enables use of small ceramic output capacitors and low-profile inductors, simplifying mechanical integration into DIN-rail or panel-mount enclosures.
Recomendado
Battery-Backed Emergency Power Pre-Regulator
Backup power systems that hold up critical loads during mains failure use a boost stage to step a low-voltage battery (12V or 18V) up to a 24V or 36V hold-up rail. The LTC7806JUFDM#WPBF's wide 4.5V to 40V input range lets a single design cover battery float, discharge, and recharge transients without input-side switching. The 2-phase topology keeps input ripple low - critical when the upstream battery is shared with RF or sensor front-ends sensitive to conducted noise.
Recomendado
Point-of-Load Front-End in Distributed Power
In distributed power architectures, an intermediate 24V or 36V bus feeds many isolated or non-isolated point-of-load converters. The LTC7806JUFDM#WPBF can serve as the front-end non-isolated boost that conditions the 12V intermediate rail up to 36V before downstream buck regulators distribute to processors, FPGAs, or analog ICs. The exposed-pad QFN-28 supports high continuous output power with minimal thermal derating in compact embedded designs.
Recomendado
ADAS Sensor Power Conditioning
Advanced Driver Assistance Systems (ADAS) including radar, lidar, and camera modules need clean, regulated rails above the 12V battery voltage to drive sensor front-ends, analog front-end ICs, and serializer/deserializer (SerDes) supplies. The LTC7806JUFDM#WPBF's AEC-Q100 screening, J-grade +150C rating, and low-EMI 2-phase 3 MHz operation make it a strong fit for pre-boost rails feeding these noise-sensitive ADAS modules. Synchronous rectification also improves light-load efficiency during parking-mode surveillance.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para LTC7806JUFDM#WPBF — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | LTC7806IUFDM#WPBF | LTC7806JUFDM#WTRPBF | LTC7806IUFDM#WTRPBF | LTC7806RUFDM#PBF | LT3576EUFE-1#TRPBF |
|---|---|---|---|---|---|---|
| Package | QFN-28 (4mm x 5mm) with EP | QFN-28 (4mm x 5mm) with EP - same | QFN-28 (4mm x 5mm) with EP - same | QFN-28 (4mm x 5mm) with EP - same | QFN-28 (4mm x 5mm) with EP - same | QFN-28 (4mm x 5mm) - same package family |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Input Voltage Range | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 40 V | 4.5 V to 40 V | Lower VIN range (older family) |
| Maximum Switching Frequency | 3 MHz | 3 MHz | 3 MHz | 3 MHz | 3 MHz | Lower max frequency |
| RoHS / Lead-Free | Yes (PBF suffix) | Yes | Yes | Yes | Yes | Yes |
Principais diferenciais
- Widest J-grade +150C junction temperature for under-hood automotive (vs LTC7806IUFDM#WPBF)
- Tube packing option for prototype-friendly low-volume orders (vs LTC7806JUFDM#WTRPBF)
- 3 MHz 2-phase synchronous boost controller for small magnetics (vs LT3576EUFE-1#TRPBF)
Notas de projeto
The QFN-28 (4mm x 5mm) package exposes its die-attach pad (EP) on the underside; this pad must be soldered to a continuous ground copper pour and stitched with a thermal via array (typically 9-12 vias, 0.3mm drill, 0.6mm pitch) to inner and opposite-side ground planes. Without this, the junction-to-ambient thermal resistance (theta_JA) rises sharply and the +150C J-grade maximum will be exceeded at full load. Estimated: with a 1 sq inch top copper pour and 9-via array, theta_JA is approximately 35 C/W; at 5W dissipation this yields ~175C junction - still tight, so additional copper or airflow is recommended for continuous high-power operation.
Route the two phase switching nodes (SW1, SW2) with short, wide traces (>= 0.5 mm width per amp) and surround them with a guard ring of ground copper tied to PGND1/PGND2. Keep the sense resistor traces (SENSE1+/-, SENSE2+/-) as a Kelvin connection directly at the sense resistor pads - any extra trace resistance adds to the measured current and degrades current-limit accuracy. Place the INTVCC bypass capacitor (1 uF X7R) within 2 mm of the INTVCC pin and the VREF bypass capacitor (0.1 uF) within 2 mm of the VREF pin to keep the internal reference quiet.
Do not skip the BST1/BST2 bootstrap capacitors (typically 0.1 uF X7R) - these provide the floating supply for the top gate driver and without them the high-side MOSFET will not switch, causing boost output to sag to VIN. Avoid minimum on-time violations at high VIN / low VOUT combinations; consult the datasheet 'Minimum On-Time' specification and choose operating frequency or inductance to stay within limits. Finally, ensure the MODE pin is configured correctly for the application's light-load behavior (Burst Mode for lowest Iq, pulse-skipping for moderate efficiency, forced-continuous for best transient response).
Informações de conformidade
RoHS and REACH compliance per ADI product page; AEC-Q100 automotive qualified per datasheet ordering information; Pb-free PBF suffix on MPN; halogen-free status not stated in provided data - left unknown.
