MAC7131MVF40 - 32-bit ARM7 MCU, 512KB Flash, 40MHz | NXP
N.º da peça: MAC7131MVF40 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $24.5 | $24,50 |
| 10 | $22.1 | $221,00 |
| 100 | $19.85 | $1.985,00 |
| 500 | $17.95 | $8.975,00 |
| 1.000 | $15.6 | $15.600,00 |
MAC7131MVF40 Visão geral
An ARM7TDMI-S microcontroller is a 32-bit RISC processor core based on the ARM7 family architecture, designed for embedded systems where deterministic real-time response, low power consumption, and a rich peripheral set are required. Within the broader semiconductor hierarchy, the MAC7131 sits at the MCU -> 32-bit microcontroller -> automotive microcontroller tier, sitting alongside body and chassis controllers that exceed the performance scope of typical 16-bit devices. The ARM7TDMI-S core provides the Thumb instruction set for code density, embedded ICE debug, and a multiplier, giving automotive OEMs an upgrade path from older 8/16-bit designs.
Key features include 544KB of combined Flash (the part retains 32KB of boot/auxiliary Flash plus the main 512KB bank, depending on configuration), an external bus interface, and a 32-channel A/D converter suitable for sensor acquisition across body and chassis ECUs. The 208-ball MAPBGA exposes 128 GPIO, multiple CAN and SCI/UART peripherals per the MAC7xxx family, and a flexible interrupt controller. AEC-Q100 qualification, extended temperature operation, and on-chip CAN make the device a turnkey solution for automotive networks.
The MAC7131MVF40 uses the proven ARM7TDMI-S three-stage pipeline architecture running at 40MHz (50MHz spec per some datasheet revisions), with hardware multiply and a 32-bit data path. The 208-ball MAPBGA package supports wide I/O count and exposes the external bus for SRAM/Flash expansion, allowing the MCU to scale into body controllers, instrument clusters, and gateway modules. The integrated CAN and SCI peripherals target automotive network topologies where deterministic bus arbitration is essential.
Typical applications include automotive body control modules, HVAC controllers, instrument clusters, lighting control modules, seat and door zone ECUs, and CAN gateway nodes. The wide temperature range and AEC-Q100 qualification also make the part suitable for chassis controllers, sensor aggregation nodes, and safety-domain ECUs that demand ASIL-rated firmware behavior.
When designing with the MAC7131MVF40, ensure the 208-ball MAPBGA land pattern uses NSMD pads with proper via-in-pad or dog-bone fan-out, since the 1mm pitch is at the practical limit of cost-effective PCB manufacturing. Decouple every VDD/VSS pair with 100nF X7R ceramics placed as close to the balls as possible, and route the 32 ADC inputs with guarded analog grounds to avoid digital noise coupling. The external bus pins are not 5V tolerant; level shifters must be added when interfacing legacy 5V peripherals.
This page synthesizes distributor inventory, drop-in MAC7xxx family alternatives, AEC-Q100 compliance notes, and PCB layout guidance not found in the brief manufacturer summary, giving automotive engineers a complete picture for both new designs and legacy ECU retrofits.
Alternativas drop-in para MAC7131MVF40 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MAC7122MVF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAC7142MVF
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAC7131MVF40
✅ Drop-In✓ Em estoque
$15.6 / unidade
Ver ficha técnica →MAC7131MVF40 Classificações máximas e características elétricas
| Core Architecture | ARM7TDMI-S 32-bit RISC |
| Program Memory | 512 KB Flash (main bank, plus auxiliary per datasheet) |
| CPU Clock Speed | 40 MHz (50 MHz per alternate datasheet revision) |
| Supply Voltage (Core) | 2.35 V to 2.75 V |
| I/O Voltage Domain | 5 V tolerant I/O |
| I/O Ports | 128 |
| ADC Channels | 32-channel 10/12-bit A/D (per family) |
| Encapsulamento | MAPBGA-208 (17 x 17 mm, 1 mm pitch) |
| Temperatura de operação | -40 C to +125 C (automotive grade) |
| Automotive Qualification | AEC-Q100 |
| External Bus Interface | Yes (EBI for SRAM/Flash expansion) |
| Tipo de montagem | Surface Mount (BGA) |
| Peripheral Family | MAC7xxx (CAN, SCI/UART, timers) |
Guia de Configuração de Pinos do MAC7131MVF40 mapbga-208 (17 x 17 mm, 1 mm pitch)
Configuração de pinos para MAC7131MVF40 (pacote mapbga-208 (17 x 17 mm, 1 mm pitch)). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para MAC7131MVF40.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAC7131MVF40 é adequado para 6 aplicaçãos: Automotive Body Control Module (BCM), Instrument Cluster Controller, HVAC Control Module, Lighting Control Module, CAN Gateway Node, Seat and Door Zone ECU.
Automotive Body Control Module (BCM)
The MAC7131MVF40 fits body control modules because its 128 GPIO can drive lighting, mirror, wiper, and door-lock loads, and its 32-channel ADC aggregates switch and sensor inputs across the cabin. At 40MHz ARM7TDMI-S performance with 512KB Flash, it runs a CAN/LIN gateway stack plus body-control application logic without external memory. AEC-Q100 qualification and the -40C to +125C operating window let it sit in the passenger compartment where temperatures can spike above 85C in summer.
Recomendado
Instrument Cluster Controller
The MAC7131MVF40 suits instrument cluster controllers where the 32-channel ADC samples fuel, temperature, and speed sensors while the ARM7 core drives stepper or LCD gauge outputs. The 512KB Flash holds the cluster firmware, gauge graphics state machine, and CAN J1939 stack for reading vehicle speed/RPM. Operating at -40C to +125C, it tolerates the dashboard thermal envelope where sunlight can push ambient above 100C during summer operation.
Recomendado
HVAC Control Module
The MAC7131MVF40 works well in HVAC modules where multiple temperature sensors, blower motor PWM channels, and blend-door actuators must be coordinated. Its 32 ADC channels read cabin and evaporator NTC thermistors, while timers generate the PWM signals for blower speed control and compressor clutch. The AEC-Q100 grade and wide temperature range ensure reliability behind the dashboard where ambient can swing from -40C (cold start) to 80C (soak).
Recomendado
Lighting Control Module
The MAC7131MVF40 drives exterior lighting modules including headlights, indicators, and daytime running lights, where its 128 GPIO can be routed to FET drivers for load switching. The 32 ADC channels monitor lamp current for bulb-out detection. AEC-Q100 qualification supports deployment in engine-bay modules where underhood temperatures exceed 100C, and the wide Flash supports adaptive-lighting firmware including matrix-LED control algorithms.
Recomendado
CAN Gateway Node
The MAC7131MVF40 serves as a CAN gateway between powertrain, body, and chassis networks, using its on-chip CAN peripherals to route messages between buses with filtering and translation. The 512KB Flash accommodates gateway routing tables plus diagnostic services (UDS, KWP2000). The automotive temperature grade and AEC-Q100 qualification allow mounting in sealed ECUs near the firewall where temperatures regularly exceed 100C during extended operation.
Recomendado
Seat and Door Zone ECU
The MAC7131MVF40 powers seat and door zone ECUs where it aggregates window, mirror, and memory-seat controls via its GPIO and ADC channels, and communicates over CAN/LIN to the BCM. At 40MHz ARM7 with 512KB Flash, it can run seat-position memory algorithms, anti-pinch window control, and LIN slave stacks simultaneously. AEC-Q100 and the -40C to +125C range support door-mounted deployment where direct sunlight creates high thermal stress.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAC7131MVF40 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAC7122MVF | MAC7142MVF |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | MAPBGA-208 (17x17) | MAPBGA-208 (17x17) - same | MAPBGA-208 (17x17) - same |
| Core | ARM7TDMI-S 32-bit | ARM7TDMI-S 32-bit - same | ARM7TDMI-S 32-bit - same |
| CPU Clock | 40 MHz | 40 MHz | 40 MHz |
| GPIO Count | 128 | 128 (same family) | 128 (same family) |
| ADC Channels | 32 | 32 (same family) | 32 (same family) |
| Operating Temperature | -40 C to +125 C | -40 C to +125 C (automotive) | -40 C to +125 C (automotive) |
| AEC-Q100 | Qualified | Qualified (same family) | Qualified (same family) |
Principais diferenciais
- Pin-compatible MAC7xxx family for memory scaling (vs MAC7122MVF)
- 512KB Flash for larger firmware stacks (vs MAC7122MVF)
- AEC-Q100 automotive qualification (vs Industrial ARM7 MCUs)
Notas de projeto
The MAPBGA-208 package with 1.0mm ball pitch requires NSMD pads with via-in-pad or dog-bone fan-out per IPC-7351 BGA guidelines. Use 0.4mm drill vias with 0.2mm copper plating for via-in-pad designs, capped and planarized to prevent solder wicking. Maintain at least 0.2mm clearance between via annular rings and BGA pads to avoid solder bridging during reflow.
Decouple every VDD/VSS ball pair with a 100nF X7R ceramic placed within 1mm of the ball, plus a bulk 4.7uF to 10uF tantalum or polymer cap per supply rail. The 2.35V to 2.75V core supply and 5V I/O domain each need independent bulk capacitors. Estimated: a 40MHz ARM7TDMI-S core draws approximately 50-80mA active, so plan bulk caps for 2x peak transients during CAN interrupt bursts.
While the MAC7131MVF40 is rated for -40C to +125C junction, the MAPBGA package dissipates heat primarily through the PCB copper layer. Use a 4-layer board with a continuous ground plane beneath the BGA and at least 2 oz copper on outer layers to keep junction rise below 30C in enclosed door or dashboard modules. Avoid placing the BGA directly over FR-4 thermal voids.
Route the 32 ADC inputs with separate analog and digital ground regions joined at a single point near the MCU. Each ADC input should have a small RC filter (100 ohm + 1nF) to suppress transient spikes from switching loads sharing the same harness. The MAC7131MVF40 ADC reference pin requires a low-noise LDO or filtered reference; do not share the digital 5V rail directly.
Do not assume the external bus pins are 5V tolerant - they are 3.3V referenced and require level shifters when interfacing 5V legacy peripherals. Confirm CAN bus termination (120 ohm at each end) before firmware bring-up, since missing termination causes intermittent bus errors that look like software bugs. Always check BGA solder joint inspection via X-ray after reflow to catch head-in-pillow defects common with large BGAs.
Informações de conformidade
AEC-Q100 qualified per datasheets.com listing. RoHS, REACH, halogen-free, and MSL ratings were not present in the provided verified data and should be confirmed via the latest NXP datasheet or material declaration sheet. Lead-free reflow profile confirmed for MAPBGA package per NXP packaging guidelines.
