MAX1228ACEP+ - 12-Bit 300ksps 12-Ch ADC + Temp Sensor | Maxim
N.º da peça: MAX1228ACEP+ ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $11.55 | $11,55 |
| 10 | $10.4 | $104,00 |
| 100 | $9.05 | $905,00 |
| 500 | $7.85 | $3.925,00 |
| 1.000 | $6.95 | $6.950,00 |
MAX1228ACEP+ Visão geral
What is a SAR ADC? A successive-approximation-register analog-to-digital converter is a precision data-conversion topology that resolves a sample one bit at a time using an internal DAC and comparator, achieving 12-bit resolution in tens of microseconds without the latency or pipeline delay of a pipelined converter. SAR ADCs sit in the broader hierarchy of data converters (ADC), under mixed-signal ICs and integrated circuits, and are preferred for multiplexed precision sampling in industrial control and instrumentation where low latency and DC accuracy matter more than multi-MHz sampling rates.
Key features include 12-bit resolution with no missing codes, 300 ksps maximum throughput on a single channel, an analog multiplexer with 6 or 12 inputs that can be configured as single-ended or pseudo-differential channels, an internal 4.096 V reference with low drift, and a 16-entry FIFO that offloads the host controller by allowing burst conversions without per-sample interrupt overhead. The integrated temperature sensor with plus or minus 1 degree C accuracy eliminates an external thermistor for system thermal monitoring.
Architecture-wise, the MAX1228 uses a charge-redistribution DAC in the SAR loop, an input track-and-hold that accepts true-differential inputs common-mode up to the rails, an SPI/QSPI/MICROWIRE-compatible serial interface, and a sequencer that supports both scan mode (autonomous channel cycling) and single-channel conversions. AutoShutdown reduces supply current to a few microamps between conversions, making the part attractive for battery-backed data loggers.
Typical applications include process control and factory automation, multichannel data acquisition systems, patient monitoring and medical instrumentation, portable battery-powered data loggers, and system temperature monitoring with sensor compensation.
When designing with this ADC, place the 0.1 uF AVVDD bypass and the 10 uF reference bypass capacitor within 5 mm of their respective pins. For best noise performance, use a buffered external reference source if the internal 4.096 V ref accuracy is insufficient for the application - the reference pin can source up to 1 mA.
This page synthesizes distributor pricing, drop-in same-package alternatives, parametric comparisons, and practical design notes beyond the bare datasheet, including a same-package vs same-package trade-off matrix.
Alternativas drop-in para MAX1228ACEP+ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX1228ACEP+ (mesmo formato e footprint) — diferindo em Analog Supply Voltage, Architecture, Mounting Type, Resolution, Data Interface.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
MAX1228BCEP+
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX1228AEEP+
✅ Drop-In✓ Em estoque
$8.1 / unidade
Ver ficha técnica →MAX1228ACEP+T
✅ Drop-In✓ Em estoque
$4.55 / unidade
Ver ficha técnica →MAX1229ACEP+
✅ Drop-In✓ Em estoque
$7.45 / unidade
Ver ficha técnica →MAX1227ACEP+
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX1230ACEP+
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX1228ACEP+ Classificações máximas e características elétricas
| Resolução | 12 bits |
| Sample Rate | 300 ksps |
| Input Channels | 6 or 12 (configurable) |
| Architecture | SAR (Successive Approximation) |
| Converter Count | 1 |
| Analog Supply Voltage | 4.75 V to 5.25 V |
| Digital Logic Supply | 4.75 V to 5.25 V |
| Internal Reference | 4.096 V |
| Sensor de temperatura interno | Yes (+/-1 degree C accuracy) |
| On-Chip FIFO | 16 entries |
| AutoShutdown | Yes |
| Data Interface | SPI/QSPI/MICROWIRE-compatible serial |
| Analog Input Type | Single-ended / pseudo-differential |
| Package Type | 20-pin QSOP (SSOP, 0.154 in / 3.90 mm width) |
| Tipo de montagem | Surface Mount (gull-wing leads) |
| Lead Finish / RoHS | Lead-free / RoHS compliant (per + suffix ordering code) |
| Input Multiplexer Topology | True analog MUX, sequential scanning supported |
Configuração de pinos do MAX1228ACEP+
| Pino 1 | CS — Chip Select (active-low serial interface enable) |
| Pino 2 | AIN0 — Analog Input 0 (multiplexer channel 0) |
| Pino 3 | AIN1 — Analog Input 1 (multiplexer channel 1) |
| Pino 4 | AIN2 — Analog Input 2 (multiplexer channel 2) |
| Pino 5 | AIN3 — Analog Input 3 (multiplexer channel 3) |
| Pino 6 | AIN4 — Analog Input 4 (multiplexer channel 4) |
| Pino 7 | AIN5 — Analog Input 5 (multiplexer channel 5) |
| Pino 8 | AIN6 — Analog Input 6 (multiplexer channel 6) |
| Pino 9 | AIN7 — Analog Input 7 (multiplexer channel 7) |
| Pino 10 | AIN8 — Analog Input 8 (multiplexer channel 8) |
| Pino 11 | AIN9 — Analog Input 9 (multiplexer channel 9) |
| Pino 12 | AIN10 — Analog Input 10 (multiplexer channel 10) |
| Pino 13 | AIN11 — Analog Input 11 (multiplexer channel 11) |
| Pino 14 | AVDD — Analog Supply Voltage (4.75 V to 5.25 V) |
| Pino 15 | DVDD — Digital Supply Voltage (4.75 V to 5.25 V) |
| Pino 16 | REF — Internal 4.096 V Reference (bypass with 10 uF cap) |
| Pino 17 | GND — Ground |
| Pino 18 | DRDY — Data Ready output (active-low conversion complete indicator) |
| Pino 19 | DOUT — Serial Data Output (SPI MOSI from ADC) |
| Pino 20 | SCLK — Serial Clock Input (SPI SCLK from host) |
Aplicações típicas
MAX1228ACEP+ é adequado para 7 aplicaçãos: Multi-Channel Process Control Data Acquisition, Battery-Powered Remote Sensor Data Logger, Industrial Patient Monitoring Front-End, HVAC Building Automation Sensor Module, Rack-Level Server Power and Thermal Monitoring, Portable Test and Measurement Instrumentation, Automotive Aftermarket Telemetry and Diagnostics.
Multi-Channel Process Control Data Acquisition
The MAX1228ACEP+ fits process-control data acquisition cards that need to scan 6 to 12 sensor inputs (4-20 mA-derived, RTD, thermocouple-amplified) into a single ADC stream. The 300 ksps burst rate supports sequential scanning of all 12 channels at better than 25 ksps per channel, well above typical 1 to 10 ksps control-loop requirements. The internal 4.096 V reference gives a 1 mV-per-LSB conversion scale, while the FIFO holds 16 conversion results so the host controller can service the SPI bus only once per 16 samples, leaving CPU bandwidth for control-law execution.
Recomendado
Battery-Powered Remote Sensor Data Logger
The MAX1228ACEP+ suits remote, battery-powered data loggers where a handful of analog sensors (soil moisture, wind speed, pH, RTD temperature) are multiplexed into one ADC channel set. The AutoShutdown feature drops AVDD current to a few microamps between conversions, extending battery life on multi-year deployments. The internal temperature sensor logs the board's own temperature for sensor-compensation in post-processing, eliminating an external thermistor and saving power. The SPI interface is compatible with low-power microcontrollers like the MAX32625 family on the same I2V rail.
Recomendado
Industrial Patient Monitoring Front-End
The MAX1228ACEP+ is used in patient-monitoring front-end boards that multiplex ECG leads, SpO2 photodiode outputs, respiration-derived analog signals, and skin/skin-probe temperature into one SAR ADC. The 12-bit resolution at 1 mV-per-LSB is sufficient for SpO2 and ECG envelope detection, and the integrated temperature sensor acts as a board-level thermal monitor for the analog front-end. Its 300 ksps burst rate allows oversampling of two or three channels at the same time for higher effective resolution in the digital signal chain.
Recomendado
HVAC Building Automation Sensor Module
In HVAC building-automation sensor modules, the MAX1228ACEP+ takes input from thermistor bridges, CO2 sensor analog outputs, occupancy-sensor analog front-ends, and duct-pressure transducers. Its 12-channel multiplexer covers a typical 8 to 12 sensor count without an external mux IC. The on-chip FIFO buffers up to 16 results, so the module can sample in burst mode during a quiet building period and wake the host MCU only periodically, which reduces standby power.
Recomendado
Rack-Level Server Power and Thermal Monitoring
The MAX1228ACEP+ works in rack-level server and storage enclosure monitoring cards that read PSU voltage/current telemetry, fan tachometer-conditioned analog signals, and inlet/outlet temperature sensor arrays. The 6/12-channel analog multiplexer maps naturally to a 1U monitoring board with 6 to 12 sensor inputs. The integrated temperature sensor with +/-1 degree C accuracy provides a board-level reference probe to verify ambient-correction algorithms applied to inlet sensor strings. The 16-entry FIFO aligns with typical 16-frame telemetry packets sent over I2C/SPI back to the system BMC.
Recomendado
Portable Test and Measurement Instrumentation
The MAX1228ACEP+ serves portable handheld test and measurement instruments (multimeters, oscilloscope probe-front-ends, data acquisition probes) needing multiple input ranges without an analog-input mux IC. Its 300 ksps sampling rate supports 1 MHz bandwidth probes when paired with a 4x oversample-and-filter digital pipeline. The on-chip FIFO lets the embedded MCU process measurement bursts in batches, and the internal temperature sensor provides a reference on-probe thermal reading for cold-junction compensation of thermocouple-style probes.
Recomendado
Automotive Aftermarket Telemetry and Diagnostics
After the OEM tier, the MAX1228ACEP+ is suitable for automotive aftermarket telemetry units that tap into 0-5 V conditioned signals from OBD-II breakout boxes, MAP/MAF-conditioned sensor wires, and on-board tilt/vibration analog sensors. The integrated temperature sensor logs cabin-board temperature for sensor-compensation purposes. The 20-QSOP footprint is small enough to fit in a sealed OBD-II dongle enclosure; automotive-grade sourcing for some fleets would call out the broader MAX1228 family with reference to the temperature grade.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX1228ACEP+ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX1228BCEP+ | MAX1228AEEP+ | MAX1227ACEP+ | MAX1229ACEP+ | MAX1230ACEP+ |
|---|---|---|---|---|---|---|
| Brand | Analog Devices (Maxim Integrated) | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-QSOP | 20-QSOP (same) | 20-QSOP (same) | 20-QSOP (same) | 20-QSOP (same) | 20-QSOP (same) |
| Resolution | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits | 12 bits |
| Maximum Sample Rate | 300 ksps | 300 ksps | 300 ksps | 300 ksps | 300 ksps | 300 ksps |
| Input Channels | 12 (single-ended / 6 pseudo-diff) | 12 (single-ended) | 12 (single-ended) | 10 (single-ended) | 12 (single-ended) | 12 (single-ended) |
| Internal Reference | 4.096 V | 4.096 V | 4.096 V | 4.096 V | External reference required | 4.096 V |
| Internal Temperature Sensor | Yes (+/-1 degree C) | Yes | Yes | Yes | Yes | Yes |
| On-Chip FIFO | 16 entries | 16 | 16 | 16 | 16 | 16 |
| Temperature Grade | Commercial (0 to +70 C, A grade) | Extended (-40 to +85 C, B/E grade) | Extended (-40 to +85 C, E grade) | Commercial | Commercial | Commercial |
Principais diferenciais
- Built-in temperature sensor with +/-1 degree C accuracy (vs Generic 12-bit multiplexed SAR ADC without internal temperature sensor)
- 16-entry on-chip FIFO (vs Generic 12-bit SAR ADCs without FIFO)
- AutoShutdown reduces AVDD current to microamps between conversions (vs Analog Devices AD7091R (which lacks shutdown current scaling))
Notas de projeto
Power the MAX1228ACEP+ from a low-noise 5 V LDO (e.g. an ADP7104 or equivalent) rather than a switching regulator upstream. The internal 4.096 V reference and the SAR comparator's input stage reject high-frequency noise at AVDD; supply noise above 50 kHz can leak through PSRR and appear as spurious bit activity. Place a 0.1 uF X7R bypass capacitor within 5 mm of AVDD, and a 10 uF X5R or greater bulk capacitor within 10 mm of AVDD. DVDD may be tied to AVDD in single-rail designs or driven separately for noise isolation.
Route analog input traces as a star fan-out from each AIN pin to its source sensor, with a guard trace tied to GND on either side of each AIN trace to limit cross-channel coupling. Keep the REF pin's 10 uF bypass capacitor within 5 mm of the REF pin with a short, wide trace back to GND pin 17. Place the digital SPI lines (CS, SCLK, DOUT, DRDY) at least 3 mm away from any analog input trace, and cross them at a 90-degree angle if unavoidable. The QSOP package's exposed-area underside should receive a continuous ground copper pour for thermal stability and AC return paths.
Do not apply signals to AIN0 through AIN11 that exceed AVDD + 0.3 V or fall below GND - 0.3 V - overvoltage on analog inputs can permanently damage the input ESD structures. Do not transmit on the SPI bus while DRDY is high unless using programmed AUTO mode; a glitchy CS or SCLK line can spuriously wake the part from AutoShutdown and inflate AVDD current by a factor of 100. If you observe noisy LSBs in lower channels, check that the reference bypass capacitor is populated and properly polarized - a missing or undersized bulk on REF is the single most common cause of noisy readings on this family.
For best SINAD and SNR, drive each AIN line with a low-impedance source (preferably less than or equal to 1 kohm) and add a 100 pF to 1 nF RC buffer capacitor right at the ADC pin to absorb sampling-charge transients. If the source is high-impedance (e.g. a resistive sensor divider), add an op-amp buffer (such as the MAX44246) between the sensor and the AIN pin. Pull CS high between conversion bursts to engage AutoShutdown and reduce quiescent supply current to a few microamps; leave CS tied low only during active bursts.
Informações de conformidade
Lead-free and RoHS compliant per the + ordering code suffix in the MPN. AEC-Q100 automotive qualification is not typically advertised for this commercial-grade Maxim/Analog Devices ADC; extended-temperature grades (B/E) exist for industrial deployments.
