MAX307EWI+ - Dual 8:1 Analog Multiplexer | Analog Devices
N.º da peça: MAX307EWI+ ✓ AtivoMAX307EWI+ Visão geral
An analog multiplexer is an input-selection switch that connects one of several signal inputs to a common output while blocking unselected paths. The MAX307 family belongs to the analog switch and multiplexer hierarchy, where precision low-resistance switching is important when the selected signal must pass with minimal voltage loss, distortion, or injected error. This makes the device suitable for multichannel measurement, data acquisition, instrumentation, and signal-routing systems.
Key features include an on-resistance below 100 Ω, matching maintained within 5 Ω between channels, and a maximum change of 7 Ω across the specified analog signal range. Off leakage remains below 2.5 nA at +85°C, while transition time is below 250 ns. These characteristics are particularly valuable when low leakage limits measurement errors and channel matching simplifies calibration of precision analog front ends.
The MAX306/MAX307 devices are monolithic CMOS multiplexers built to provide consistent resistance across selected channels. Their low resistance and low leakage reduce signal degradation in measurement paths, while fast switching supports practical acquisition and control cycles. The dual 8-channel organization allows two banks of eight inputs to be routed through one package, reducing component count when a system needs symmetrical or parallel input selection.
Typical uses include multiplexed sensor measurement, automated test equipment, battery-cell monitoring, industrial process measurement, programmable instrumentation, and multichannel data-acquisition systems. In each application, the device can reduce the number of analog front-end channels required by selecting inputs sequentially before amplification, filtering, or conversion.
Designers should pay close attention to the control logic, input voltage range, signal amplitude, and pin-specific input limits before routing external signals. Keep sensitive analog traces away from switching-control lines, use a stable supply reference, and account for charge injection and off-leakage effects when designing high-impedance measurement systems.
This page combines the manufacturer's electrical characteristics with practical routing and measurement guidance, identifies documented same-family drop-in options, and highlights the trade-offs involved when using a dual 8:1 precision multiplexer in an analog signal path.
Alternativas drop-in para MAX307EWI+ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX307EWI+ (mesmo formato e footprint) — diferindo em Multiplexer Configuration, On-Resistance, Package.
MAX307CWI+
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX307MWI/PR+T
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX307EWI+ Especificações
| Multiplexer Configuration | Dual 8:1 |
| Number of Circuits | 2 circuits |
| On-Resistance | Less than 100 ohm |
| Channel-to-Channel Matching | Within 5 ohm |
| On-Resistance Variation Across Signal Range | 7 ohm maximum |
| Specified Analog Signal Range | 5 V to 30 V |
| Off Leakage Current | Less than 2.5 nA at +85°C |
| Transition Time | Less than 250 ns |
| Encapsulamento | 28-pin WSOIC |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do MAX307EWI+ 28-pin wsoic
Configuração de pinos para MAX307EWI+ (pacote 28-pin wsoic). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MAX307EWI+.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAX307EWI+ é adequado para 6 aplicaçãos: Multiplexed Sensor Measurement, Automated Test Equipment, Battery Cell Monitoring, Programmable Instrumentation, Industrial Process Control, Data Acquisition Systems.
Multiplexed Sensor Measurement
The MAX307EWI+ suits systems that scan multiple sensor outputs through a shared amplifier or converter. Its two independent 8:1 sections reduce the number of selection switches, while on-resistance below 100 Ω and channel-to-channel matching within 5 Ω help preserve comparability among sensor channels. The specified off leakage below 2.5 nA at +85°C is valuable when high-impedance sources can otherwise create measurement errors. The primary trade-off is charge injection during selection, so allow adequate settling time after each address change and include the sensor impedance, switch resistance, filter capacitance, and amplifier input bias in the error budget.
Recomendado
Automated Test Equipment
The MAX307EWI+ can route a bank of eight test nodes to a common measurement chain for each of two groups. The less-than-100 Ω on-resistance limits insertion loss, while matching within 5 Ω improves consistency between test channels. Transition time below 250 ns helps support rapid scans, but the instrumentation must also wait for the amplifier, filter, and converter to settle after switching. Use short analog routes and keep address-control traces away from sensitive nodes to minimize coupling. This arrangement is especially useful where compact channel density and repeatable signal-path behavior are more important than bidirectional multiplexing.
Recomendado
Battery Cell Monitoring
The dual 8:1 organization of the MAX307EWI+ can help monitor two groups of eight battery-cell voltages through shared measurement circuitry. Matching within 5 Ω reduces channel-dependent gain errors, and off leakage below 2.5 nA at +85°C helps prevent unwanted current from loading high-impedance cell taps. Because the switch itself does not equalize, isolate, or measure cells, the system still needs protection, filtering, and a suitable measurement front end. Confirm the allowable common-mode voltage and control levels against the manufacturer datasheet, especially when the monitored voltage can exceed the device's specified analog signal range.
Recomendado
Programmable Instrumentation
The MAX307EWI+ fits programmable front ends that expose several analog inputs to one configurable signal-conditioning path. Its two 8-channel banks support dense routing in instrument panels, condition-monitoring systems, and laboratory measurement equipment. The low on-resistance and controlled channel matching help preserve source amplitude and calibration consistency, while sub-250 ns transitions support responsive instrument control. A practical design should model charge injection, leakage into high-impedance nodes, and settling after address changes. Place bypass and protection components near the relevant pins, and keep high-value precision traces away from the digital address lines to preserve measurement integrity.
Recomendado
Industrial Process Control
The MAX307EWI+ can consolidate multiple analog process inputs into a shared controller or data-acquisition channel. Its matched low-resistance channels reduce calibration differences between sensors, while the dual 8:1 format increases routing density in compact industrial equipment. Low off leakage limits disturbance of high-impedance sensors, and fast switching supports responsive process monitoring. Industrial implementations must still account for surge, common-mode voltage, temperature, grounding, and protection requirements; the mux is a routing element rather than a complete input-protection solution. Use isolated or protected sensor interfaces where necessary and confirm operating limits against the final environmental specification.
Recomendado
Data Acquisition Systems
The MAX307EWI+ is well suited to sequential data acquisition because it routes two sets of eight channels through one package. On-resistance below 100 Ω limits voltage loss, and matching within 5 Ω supports channel-to-channel consistency. Off leakage below 2.5 nA at +85°C is advantageous when the selected source has high output impedance. The sub-250 ns transition specification should not be confused with complete acquisition settling: include the source impedance, external capacitance, filter response, amplifier settling, and converter acquisition time in each sample period. A shielded analog layout and deliberate return paths help prevent control-edge coupling from appearing as measurement noise.
Recomendado
Dados de referência de engenharia para MAX307EWI+ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX307CWI+ | MAX307MWI/PR+T |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 28-pin WSOIC | 28-pin WSOIC | 28-pin WSOIC |
| Multiplexer Configuration | Dual 8:1 | Dual 8:1 | Dual 8:1 |
| Number of Circuits | 2 circuits | 2 circuits | 2 circuits |
Principais diferenciais
- Dual 8:1 routing in one package (vs MAX306CPI)
- Low and controlled channel resistance (vs MAX307CWI+)
- Fast switching with low off leakage (vs MAX307MWI/PR+T)
Notas de projeto
Allow the complete analog path to settle after every address change; the below-250 ns transition time describes switching action rather than final measurement accuracy. Calculate settling from source impedance, switch resistance, filter capacitance, amplifier bandwidth, and converter acquisition time. For high-impedance nodes, include charge injection and the device's sub-2.5 nA off-leakage at +85°C in the error budget.
Route the selected analog signal with short traces and a continuous return path, and keep address and enable lines away from high-impedance analog inputs. Place any input filtering or protection close to the device pins while preserving the protection limits. Because the MAX307EWI+ uses a WSOIC package with fine lead spacing, verify assembly clearances and use a package-specific land pattern rather than a generic SOIC footprint.
Do not treat the 5 V to 30 V analog signal range as the absolute maximum input rating. Confirm supply voltage, logic levels, absolute maximum input voltage, and temperature limits in the manufacturer datasheet before connecting external signals. Also distinguish switching speed from measurement settling: a fast transition does not remove the need for acquisition delay or post-switch filtering.
Informações de conformidade
The MAX307EWI+ is an industrial interface IC rather than an automotive-qualified device. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals status must be confirmed for the exact ordering code.