Analog Devices

MAX307EWI+ - Dual 8:1 Analog Multiplexer | Analog Devices

料号: MAX307EWI+ ✓ 量产中
Less than 2.5 nA at +85°C Id Less than 100 ohm Rds(on) 28-pin WSOIC Package
最小起订量: 1 |

MAX307EWI+ 概述

The Analog Devices MAX307EWI+ is a precision, dual 8:1 CMOS analog multiplexer with low on-resistance below 100 Ω, channel-to-channel matching within 5 Ω, and operation from a 5 V to 30 V analog signal range. It is packaged in a 28-pin WSOIC and provides two independently controlled multiplexers for routing eight analog inputs on each side of the device.

An analog multiplexer is an input-selection switch that connects one of several signal inputs to a common output while blocking unselected paths. The MAX307 family belongs to the analog switch and multiplexer hierarchy, where precision low-resistance switching is important when the selected signal must pass with minimal voltage loss, distortion, or injected error. This makes the device suitable for multichannel measurement, data acquisition, instrumentation, and signal-routing systems.

Key features include an on-resistance below 100 Ω, matching maintained within 5 Ω between channels, and a maximum change of 7 Ω across the specified analog signal range. Off leakage remains below 2.5 nA at +85°C, while transition time is below 250 ns. These characteristics are particularly valuable when low leakage limits measurement errors and channel matching simplifies calibration of precision analog front ends.

The MAX306/MAX307 devices are monolithic CMOS multiplexers built to provide consistent resistance across selected channels. Their low resistance and low leakage reduce signal degradation in measurement paths, while fast switching supports practical acquisition and control cycles. The dual 8-channel organization allows two banks of eight inputs to be routed through one package, reducing component count when a system needs symmetrical or parallel input selection.

Typical uses include multiplexed sensor measurement, automated test equipment, battery-cell monitoring, industrial process measurement, programmable instrumentation, and multichannel data-acquisition systems. In each application, the device can reduce the number of analog front-end channels required by selecting inputs sequentially before amplification, filtering, or conversion.

Designers should pay close attention to the control logic, input voltage range, signal amplitude, and pin-specific input limits before routing external signals. Keep sensitive analog traces away from switching-control lines, use a stable supply reference, and account for charge injection and off-leakage effects when designing high-impedance measurement systems.

This page combines the manufacturer's electrical characteristics with practical routing and measurement guidance, identifies documented same-family drop-in options, and highlights the trade-offs involved when using a dual 8:1 precision multiplexer in an analog signal path.

直接替换替代料: MAX307EWI+ ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

本系列中的变体

可与以下型号直接替换的同系列型号: MAX307EWI+ (相同外形与封装尺寸) ——差异在于 Multiplexer Configuration, On-Resistance, Package.

Maxim Integrated
Multiplexer Configuration: 2 circuits, dual 8:1
On-Resistance: 400 ohm
Package: 28-pin SOIC
对比 MAX307EWI+ →

MAX307CWI+

✅ 直接替换
📦 28-pin WSOIC
Same dual 8:1 mux, sub-100 ohm on-resistance, 5 ohm channel matching, and sub-250 ns transition time; temperature-grade suffix differs from the E-grade target.

📋 参考替代料(不在目录中)

MAX307MWI/PR+T

✅ 直接替换
📦 28-pin WSOIC
Same dual 8:1 mux and 28-pin WSOIC construction; temperature-grade suffix differs while the core sub-100 ohm resistance and 5 ohm matching characteristics remain unchanged.

📋 参考替代料(不在目录中)

MAX307EWI+ 规格参数

Multiplexer Configuration Dual 8:1
Number of Circuits 2 circuits
On-Resistance Less than 100 ohm
Channel-to-Channel Matching Within 5 ohm
On-Resistance Variation Across Signal Range 7 ohm maximum
Specified Analog Signal Range 5 V to 30 V
Off Leakage Current Less than 2.5 nA at +85°C
Transition Time Less than 250 ns
封装 28-pin WSOIC
安装类型 Surface mount

MAX307EWI+ 28-pin wsoic 引脚配置指南

MAX307EWI+(28-pin wsoic 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。

MAX307EWI+ 的 28-pin wsoic 封装引脚图

暂无详细引脚数据: MAX307EWI+.

请参阅 数据手册 以查看完整引脚配置。

典型应用

MAX307EWI+ 适用于 6 应用s: Multiplexed Sensor Measurement, Automated Test Equipment, Battery Cell Monitoring, Programmable Instrumentation, Industrial Process Control, Data Acquisition Systems.

🧩

Multiplexed Sensor Measurement

The MAX307EWI+ suits systems that scan multiple sensor outputs through a shared amplifier or converter. Its two independent 8:1 sections reduce the number of selection switches, while on-resistance below 100 Ω and channel-to-channel matching within 5 Ω help preserve comparability among sensor channels. The specified off leakage below 2.5 nA at +85°C is valuable when high-impedance sources can otherwise create measurement errors. The primary trade-off is charge injection during selection, so allow adequate settling time after each address change and include the sensor impedance, switch resistance, filter capacitance, and amplifier input bias in the error budget.

🏭

Automated Test Equipment

The MAX307EWI+ can route a bank of eight test nodes to a common measurement chain for each of two groups. The less-than-100 Ω on-resistance limits insertion loss, while matching within 5 Ω improves consistency between test channels. Transition time below 250 ns helps support rapid scans, but the instrumentation must also wait for the amplifier, filter, and converter to settle after switching. Use short analog routes and keep address-control traces away from sensitive nodes to minimize coupling. This arrangement is especially useful where compact channel density and repeatable signal-path behavior are more important than bidirectional multiplexing.

⚡

Battery Cell Monitoring

The dual 8:1 organization of the MAX307EWI+ can help monitor two groups of eight battery-cell voltages through shared measurement circuitry. Matching within 5 Ω reduces channel-dependent gain errors, and off leakage below 2.5 nA at +85°C helps prevent unwanted current from loading high-impedance cell taps. Because the switch itself does not equalize, isolate, or measure cells, the system still needs protection, filtering, and a suitable measurement front end. Confirm the allowable common-mode voltage and control levels against the manufacturer datasheet, especially when the monitored voltage can exceed the device's specified analog signal range.

📊

Programmable Instrumentation

The MAX307EWI+ fits programmable front ends that expose several analog inputs to one configurable signal-conditioning path. Its two 8-channel banks support dense routing in instrument panels, condition-monitoring systems, and laboratory measurement equipment. The low on-resistance and controlled channel matching help preserve source amplitude and calibration consistency, while sub-250 ns transitions support responsive instrument control. A practical design should model charge injection, leakage into high-impedance nodes, and settling after address changes. Place bypass and protection components near the relevant pins, and keep high-value precision traces away from the digital address lines to preserve measurement integrity.

🏭

Industrial Process Control

The MAX307EWI+ can consolidate multiple analog process inputs into a shared controller or data-acquisition channel. Its matched low-resistance channels reduce calibration differences between sensors, while the dual 8:1 format increases routing density in compact industrial equipment. Low off leakage limits disturbance of high-impedance sensors, and fast switching supports responsive process monitoring. Industrial implementations must still account for surge, common-mode voltage, temperature, grounding, and protection requirements; the mux is a routing element rather than a complete input-protection solution. Use isolated or protected sensor interfaces where necessary and confirm operating limits against the final environmental specification.

🖥️

Data Acquisition Systems

The MAX307EWI+ is well suited to sequential data acquisition because it routes two sets of eight channels through one package. On-resistance below 100 Ω limits voltage loss, and matching within 5 Ω supports channel-to-channel consistency. Off leakage below 2.5 nA at +85°C is advantageous when the selected source has high output impedance. The sub-250 ns transition specification should not be confused with complete acquisition settling: include the source impedance, external capacitance, filter response, amplifier settling, and converter acquisition time in each sample period. A shielded analog layout and deliberate return paths help prevent control-edge coupling from appearing as measurement noise.

What is the MAX307EWI+ used for?
The MAX307EWI+ is used to route analog signals from eight inputs to one output in each of two independent multiplexer circuits. According to the Analog Devices MAX306/MAX307 datasheet, Revision 5, it is a precision monolithic CMOS analog multiplexer with on-resistance below 100 Ω, channel matching within 5 Ω, and transition time below 250 ns. It is particularly useful in data-acquisition, instrumentation, sensor-monitoring, and automated test systems where one analog measurement chain must scan multiple inputs.
What are the key specifications of MAX307EWI+ that engineers should know?
The MAX307EWI+ is a dual 8:1 precision CMOS analog multiplexer in a 28-pin WSOIC package. The Analog Devices MAX306/MAX307 datasheet, Revision 5, specifies on-resistance below 100 Ω, channel-to-channel matching within 5 Ω, no more than 7 Ω resistance variation across the 5 V to 30 V signal range, off leakage below 2.5 nA at +85°C, and transition time below 250 ns. These figures define its suitability for low-leakage, precision analog-routing applications.
How many channels and multiplexer circuits does MAX307EWI+ contain?
The MAX307EWI+ contains two independent 8:1 multiplexer circuits, providing a total of 16 selectable analog inputs across the device. The Analog Devices MAX306/MAX307 datasheet, Revision 5, identifies the MAX307 as a dual 8-channel high-performance CMOS analog multiplexer. This organization allows two groups of eight signals to be selected with the same package, which can simplify symmetric measurement or control architectures while reducing the number of separate multiplexer components required.
What is the on-resistance of MAX307EWI+?
The MAX307EWI+ has an on-resistance of less than 100 Ω. According to the Analog Devices MAX306/MAX307 datasheet, Revision 5, that resistance is matched to within 5 Ω between channels and remains flat across the specified 5 V to 30 V analog signal range, with a maximum variation of 7 Ω. Low and consistent on-resistance helps reduce signal-dependent attenuation and makes channel-to-channel comparison more predictable in precision measurement systems.
What is the switching speed of MAX307EWI+?
The MAX307EWI+ transitions in less than 250 ns. The Analog Devices MAX306/MAX307 datasheet, Revision 5, lists this figure as tTRANS, describing the time required for the analog switch to change state. Such fast switching supports multiplexed acquisition and control systems, although the complete acquisition period must also allow for settling of the downstream amplifier, filter, and converter after each channel change.
Is MAX307EWI+ suitable for high-impedance sensor measurement?
The MAX307EWI+ is suitable for many high-impedance sensor-measurement systems because its off leakage is specified below 2.5 nA at +85°C. According to the Analog Devices MAX306/MAX307 datasheet, Revision 5, its on-resistance remains below 100 Ω with matching within 5 Ω. Actual suitability depends on source impedance, sensor leakage, settling time, and the input bias current of the following amplifier, so the complete analog path should be evaluated together.
What is the difference between MAX307EWI+ and MAX307CWI+?
Both parts use the same precision dual 8:1 CMOS multiplexer architecture and are identified in the MAX307 family documentation, but their temperature-grade ordering codes differ. The MAX307EWI+ carries the E/W/I ordering combination, while MAX307CWI+ carries the C/W/I combination. Exact operating-temperature limits and production-status details should be confirmed in the manufacturer datasheet before treating either device as an automatic replacement in an application with a wide environmental range.
When should I choose MAX307EWI+ over MAX306CPI?
Choose MAX307EWI+ when the design requires the 28-pin WSOIC MAX307 footprint and a dual 8:1 switching organization. The MAX306CPI comparison describes a different family variant and package ordering code, so its physical footprint and control configuration must be checked before substitution. For a new design, the MAX307EWI+ is preferable when two 8-channel analog selection blocks, sub-100 Ω on-resistance, low leakage, and sub-250 ns transitions align with the signal-path requirements.
What can replace MAX307EWI+?
The documented same-family drop-in choices include MAX307CWI+ and MAX307MWI/PR+T in the 28-pin WSOIC format. Their key distinction is the temperature-grade ordering code rather than the dual 8:1 mux topology, although operating limits and availability must be checked against the target application. A cross-brand device should not be treated as a drop-in replacement unless its manufacturer explicitly confirms the same 28-pin footprint, control logic, and electrical limits.
What is the best competitor equivalent for MAX307EWI+?
No cross-brand drop-in equivalent is established for the MAX307EWI+ based on the available manufacturer and distributor references. The safest replacements are documented Analog Devices MAX307 variants using the same 28-pin WSOIC format, such as MAX307CWI+ and MAX307MWI/PR+T. For any proposed competitor, verify pinout, address and control logic, supply voltage, on-resistance, leakage, transition time, and operating-temperature requirements before replacing the device in a live design.
Is MAX307EWI+ suitable for data acquisition and test equipment?
Yes, the MAX307EWI+ fits multiplexed data-acquisition and test-equipment signal paths because it combines two 8:1 muxes with less than 100 Ω on-resistance, channel matching within 5 Ω, and transition time below 250 ns. The Analog Devices MAX306/MAX307 datasheet, Revision 5, supports its use in precision measurement systems. Design the downstream settling time and charge-injection behavior into the acquisition cycle rather than relying only on the transition-time rating.
Where to download the MAX307EWI+ datasheet PDF?
The MAX307EWI+ datasheet PDF is available from the official Analog Devices MAX306/MAX307 document at analog.com. It is identified as Data Sheet Revision 5 and contains the multiplexer's electrical characteristics, operating information, ordering details, and package information. Use the manufacturer document for design decisions and consult the exact ordering-code suffix when confirming temperature grade, package form, and shipping configuration.
Where can I find the MAX307EWI+ pinout?
The MAX307EWI+ pinout is located in the pin-description and package-drawing sections of the official Analog Devices MAX306/MAX307 datasheet, Revision 5. The device is supplied in a 28-pin WSOIC package, but the verified manufacturer text does not expose the individual pin names needed for a complete numbered diagram. Use the datasheet pin table when assigning control inputs, supply pins, common terminals, and analog channels to avoid errors in signal routing.
How do I use MAX307EWI+ in a PCB layout?
Place analog input and common-route connections to minimize trace resistance and coupling to digital control lines. Keep the MAX307EWI+ close to the source and destination of the selected signal when settling time is important, and route address and enable signals away from high-impedance analog nodes. The device's below-250 ns transition capability does not eliminate charge injection or settling time, so use grounded guard structures, suitable impedance paths, and a complete analog-plus-layout simulation before production.
Where can I request a quote for MAX307EWI+?
Use the Request a Quote form on this page to request the MAX307EWI+ and current commercial terms. The form is the appropriate route for unit availability, quantity pricing, lead time, and shipping questions because market conditions can change quickly. The part is listed in production by Analog Devices and is offered in a 28-pin WSOIC package; confirm the exact suffix, order quantity, and delivery schedule when submitting the request.
Is MAX307EWI+ currently in production?
The MAX307EWI+ is currently marked as a production part on the official Analog Devices product page. The MAX306/MAX307 datasheet is identified as Revision 5, indicating that the family remains supported for current design work. For a new production release, still confirm the exact MAX307EWI+ ordering code, lifecycle status, and delivery commitment at the time of purchase through the Request a Quote form.

工程参考数据: MAX307EWI+ ——对比、设计指导和合规信息。

选型指南

Choose the MAX307EWI+ when the PCB requires the 28-pin WSOIC footprint, two independent 8:1 analog sections, on-resistance below 100 Ω, channel matching within 5 Ω, and a specified 5 V to 30 V analog signal range. It is particularly suitable for multiplexed sensor measurement, automated test equipment, and data-acquisition systems where two groups of eight signals can share precision front-end circuitry. MAX307CWI+ is the documented same-package alternative when its temperature-grade limits suit the installation. MAX307MWI/PR+T is the same-package option to consider when its environmental grade and order configuration meet the product requirements. Do not select MAX306CPI without a complete footprint and logic review because it belongs to a different family variant. No cross-brand part should be treated as a drop-in without explicit confirmation of the 28-pin pinout, control interface, voltage limits, leakage, switching speed, and temperature range.

与替代料对比

参数 本产品 MAX307CWI+ MAX307MWI/PR+T
Brand Analog Devices Analog Devices Analog Devices
Package 28-pin WSOIC 28-pin WSOIC 28-pin WSOIC
Multiplexer Configuration Dual 8:1 Dual 8:1 Dual 8:1
Number of Circuits 2 circuits 2 circuits 2 circuits

关键差异点

  • Dual 8:1 routing in one package (对比 MAX306CPI)
  • Low and controlled channel resistance (对比 MAX307CWI+)
  • Fast switching with low off leakage (对比 MAX307MWI/PR+T)

设计说明

Allow the complete analog path to settle after every address change; the below-250 ns transition time describes switching action rather than final measurement accuracy. Calculate settling from source impedance, switch resistance, filter capacitance, amplifier bandwidth, and converter acquisition time. For high-impedance nodes, include charge injection and the device's sub-2.5 nA off-leakage at +85°C in the error budget.

Route the selected analog signal with short traces and a continuous return path, and keep address and enable lines away from high-impedance analog inputs. Place any input filtering or protection close to the device pins while preserving the protection limits. Because the MAX307EWI+ uses a WSOIC package with fine lead spacing, verify assembly clearances and use a package-specific land pattern rather than a generic SOIC footprint.

Do not treat the 5 V to 30 V analog signal range as the absolute maximum input rating. Confirm supply voltage, logic levels, absolute maximum input voltage, and temperature limits in the manufacturer datasheet before connecting external signals. Also distinguish switching speed from measurement settling: a fast transition does not remove the need for acquisition delay or post-switch filtering.

合规信息

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

The MAX307EWI+ is an industrial interface IC rather than an automotive-qualified device. Exact RoHS, REACH, lead-free, halogen-free, and conflict-minerals status must be confirmed for the exact ordering code.

数据核验日期: 2026-11-14 ——数据由 XAIPART 元器件工程团队核验和整理

相关搜索

MAX307EWI+ datasheet MAX307EWI+ pinout MAX307EWI+ datasheet pdf MAX307EWI+ equivalent MAX307EWI+ replacement MAX307EWI+ cross reference MAX307EWI+ footprint MAX307EWI+ price MAX307EWI+ stock Analog Devices MAX307EWI+ MAX307EWI+ vs MAX307CWI+ MAX307 dual 8:1 WSOIC multiplexer

相关元器件 & 术语

Analog Devices MAX307EWI+ MAX307CWI+ MAX307MWI/PR+T MAX306CPI MAX306 MAX307 analog multiplexer multiplexer and demultiplexer analog switch interface IC semiconductor CMOS dual 8:1 multiplexer 28-pin WSOIC surface-mount package on-resistance channel matching off leakage transition time charge injection sensor measurement data acquisition automated test equipment
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情