MAX318CPA+ - 35 Ohm SPST CMOS Analog Switch | Analog Devices
N.º da peça: MAX318CPA+ ✓ AtivoMAX318CPA+ Visão geral
An analog switch is a semiconductor interface device that connects or disconnects an analog signal path under digital control. The MAX318CPA+ belongs to the analog switch hierarchy within interface ICs and multiplexers, providing a simpler alternative to a multi-channel multiplexer when only one signal path must be selected. Its normally open configuration keeps the switched node disconnected until the control input activates the path.
Key characteristics include a maximum on-resistance of 35 ohms, operation from 4.5 V to 20 V, and normally open SPST behavior. The device is specified as a precision CMOS analog switch with low on-resistance that remains substantially flat across the analog signal range. According to the Analog Devices MAX318 product page, on-resistance is guaranteed below 35 ohms and is matched within 2 ohms between channels in the associated precision-switch family.
The MAX318CPA+ is intended for precision instrumentation, signal routing, test and measurement equipment, industrial control interfaces, and data acquisition systems. Its single-channel architecture simplifies control logic while preserving the low resistance required to transfer low-level or precision analog signals. The 8-pin PDIP package also supports conventional through-hole assembly and prototype boards where fine-pitch surface-mount routing would be inconvenient.
Designers should verify the control logic, supply voltage, allowable signal voltage, and switching transients against the manufacturer data sheet before use. Because an analog switch can introduce small resistance variation, channel resistance matching, charge injection, off leakage, and bandwidth determine whether it is suitable for a particular signal path. Input and output protection may also be required when external voltages exceed the device ratings.
This page combines the manufacturer specifications, verified sourcing links, application guidance, comparison information, and practical design notes to support component selection and PCB implementation. The MAX318CPA+ is best suited to designers who need a simple, normally open, precision SPST switch rather than a multi-channel multiplexer.
Alternativas drop-in para MAX318CPA+ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
MAX318MJA
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MAX318EPA+
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MAX318CPA+ Classificações máximas e características elétricas
| Switch Type | SPST, normally open |
| Number of Channels | 1 channel |
| On-Resistance | 35 ohms maximum |
| On-Resistance Matching | Within 2 ohms between channels in the MAX317/MAX318/MAX319 family |
| On-Resistance Variation Over Analog Signal Range | 3 ohms maximum |
| Supply Voltage Range | 4.5 V to 20 V |
| Switch Configuration | 1:1 |
| Technology | CMOS |
| Encapsulamento | 8-pin PDIP |
| Contagem de pinos | 8 pins |
| Tipo de montagem | Through-hole |
Guia de Configuração de Pinos do MAX318CPA+ 8-pin pdip
Configuração de pinos para MAX318CPA+ (pacote 8-pin pdip). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para MAX318CPA+.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MAX318CPA+ é adequado para 6 aplicaçãos: Precision Instrumentation Signal Routing, Test and Measurement Systems, Industrial Control Signal Isolation, Data Acquisition Modules, Laboratory Equipment, Battery-Powered Portable Instruments.
Precision Instrumentation Signal Routing
The MAX318CPA+ suits precision measurement front ends that must connect one analog source to an instrument or converter. Its normally open SPST configuration avoids leaving the selected node unintentionally connected, while the maximum on-resistance of 35 ohms provides a defined insertion resistance for the signal path. According to the Analog Devices MAX318 family information, precision switches maintain channel matching within 2 ohms and on-resistance variation within 3 ohms across the analog range. These characteristics help control measurement error when source impedance is low. The designer should still calculate the total signal-path impedance, confirm the allowable input swing, and verify settling behavior for the selected bandwidth before finalizing the interface.
Recomendado
Test and Measurement Systems
The MAX318CPA+ can serve as a compact signal-selection element in test equipment that routes a source, reference, or calibration node into a measurement chain. The one-channel, normally open SPST arrangement is useful when the test path must remain isolated until commanded. Its 35 ohm maximum on-resistance must be included in the input impedance of the downstream instrument, particularly for high-impedance sensor interfaces. The manufacturer identifies the MAX318 family as low-resistance precision CMOS switches, with matching and variation guarantees relevant to repeatable measurements. For automated test equipment, check control timing, charge injection, off leakage, and the maximum signal excursion before assigning the switch to a sensitive input.
Recomendado
Industrial Control Signal Isolation
The MAX318CPA+ is appropriate for industrial interfaces that temporarily connect a sensor or control node to an analog processing circuit. Its normally open state provides a default disconnected path, which can prevent unwanted interaction between external circuitry and a protected measurement channel. The 35 ohm maximum on-resistance should be checked against the sensor output impedance and the input impedance of the receiving circuit. Because industrial signals can exceed the device supply voltage or switch thresholds, external protection and clamping may be necessary. The Analog Devices MAX318 documentation remains the controlling reference for allowable signal voltages and control levels. Firmware and hardware designers should also ensure that fault states cannot place an uncontrolled voltage on the selected node.
Recomendado
Data Acquisition Modules
A MAX318CPA+ can connect a selected source into a data-acquisition channel when a single switched analog input is sufficient. The 4.5 V to 20 V operating range accommodates conventional analog supply rails, and the 35 ohm maximum on-resistance is generally easier to manage than the contribution of a long cable or high-impedance sensor. Engineers should evaluate the complete acquisition path because switch resistance, leakage, settling time, and protection-network leakage all contribute to acquisition error. The normally open function also supports circuits where a source should be connected only during a measurement window. Use the manufacturer data sheet to confirm the signal range and switching behavior, then place the device close enough to the acquisition input to minimize induced pickup and PCB leakage effects.
Recomendado
Laboratory Equipment
The MAX318CPA+ is well matched to laboratory equipment that uses removable or selectable analog inputs, including calibration and reference-routing arrangements. The through-hole 8-pin PDIP package is convenient for prototypes, instrument modules, and manually assembled boards. Because the switch is normally open, it can isolate an external input until the instrument establishes a defined connection. Designers should assess connector transients, grounding, and leakage from adjacent laboratory circuitry; the 35 ohm maximum on-resistance must also be included in the probe and input network. The Analog Devices family specifications establish low on-resistance and controlled matching, while exact bandwidth, leakage, and switching limits should be taken from the MAX318 data sheet for the final operating conditions.
Recomendado
Battery-Powered Portable Instruments
The MAX318CPA+ can be used in a portable measurement instrument when the design requires a low-component-count analog routing switch and can operate from a 4.5 V or higher supply. The normally open configuration reduces unintended signal-path loading, while the specified 35 ohm maximum on-resistance provides a known upper bound for path-loss calculations. Low-power designs must still verify supply current and static dissipation under the operating state because those figures are not established by the distributor summary. Protection against connector transients and electrostatic discharge is particularly important in portable equipment. Keep the analog traces short, maintain a stable ground reference, and consult the manufacturer data sheet for control thresholds, leakage, and allowable external signal excursions.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX318CPA+ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX318MJA | MAX318EPA+ |
|---|---|---|---|
| Package | 8-pin PDIP | 8-pin PDIP | 8-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Switch Type | SPST, normally open | SPST, normally open | SPST, normally open |
| Number of Channels | 1 channel | 1 channel | 1 channel |
| On-Resistance | 35 ohms maximum | 35 ohms maximum | 35 ohms maximum |
| Supply Voltage Range | 4.5 V to 20 V | 4.5 V to 20 V | 4.5 V to 20 V |
| Technology | CMOS | CMOS | CMOS |
| On-Resistance Matching | Within 2 ohms between channels in the associated precision-switch family | Within 2 ohms between channels in the associated precision-switch family | Within 2 ohms between channels in the associated precision-switch family |
| On-Resistance Variation | 3 ohms maximum across the analog signal range | 3 ohms maximum across the analog signal range | 3 ohms maximum across the analog signal range |
Principais diferenciais
- Single-channel normally open precision switch (vs MAX318MJA)
- No multi-channel switching complexity (vs MAX318MJA)
- Defined insertion resistance for precision paths (vs MAX318EPA+)
Notas de projeto
Include the maximum 35 ohm on-resistance in the complete source impedance calculation rather than treating the switch as ideal. The 2 ohm family matching and 3 ohm signal-range variation are important when comparing channels or measuring small differential signals. For high-impedance sources, verify leakage, capacitance, bandwidth, and settling time from the manufacturer data sheet because the 35 ohm figure alone does not determine accuracy.
Route the analog input and output as short traces with a continuous ground reference, and keep switching-control traces away from sensitive analog nets. The through-hole PDIP package is mechanically simple, but long leads can increase inductance, capacitance, and pickup. If the switch handles fast signals, use a ground plane, minimize loop area, and provide local supply bypassing close to the device.
Operate the MAX318CPA+ only within its 4.5 V to 20 V supply range and confirm that control thresholds are compatible with the driving logic. External signals must also remain inside the allowable input or output voltage window. Add series resistance, clamps, or other protection when connector transients or powered external nodes could exceed those limits; protection components can add leakage that must be included in the measurement budget.
Do not substitute the normally closed MAX317 or the SPDT MAX319 solely because they use the same precision-switch family. The MAX318CPA+ is normally open, so the control logic and default switch state differ. Also verify that any proposed alternative has the same 8-pin PDIP terminal assignments and electrical limits rather than relying on the package outline alone.
Informações de conformidade
Compliance status requires confirmation from the current Analog Devices product documentation or an applicable supplier declaration for the exact ordering suffix.