MAX3232CSE+TG1Z - 1Mbps Dual RS-232 Transceiver | Analog Devices
N.º da peça: MAX3232CSE+TG1Z ✓ AtivoMAX3232CSE+TG1Z Visão geral
An RS-232 transceiver is a communications interface IC used to connect a modern microcontroller, programmable logic controller, or computer serial port with equipment that uses the RS-232 standard. The MAX3232 belongs to the broader line-driver and receiver hierarchy, combines two RS-232 drivers with two receivers, and eliminates the need for a separate negative supply. Its true RS-232 implementation also supports low-power portable equipment connected to external data and control systems.
The MAX3232CSE+TG1Z operates from a 3.0V to 5.5V supply and supports communication rates up to 1Mbps. It uses four 0.1uF charge-pump capacitors to generate the voltage levels required by true RS-232 transmitters. The manufacturer describes the MAX3232 family as pin, package, and functionally compatible with industry-standard RS-232 interfaces, which simplifies design reuse when the electrical requirements and operating conditions match.
Its dual-channel architecture allows one serial link to carry data in both directions or supports two independent unidirectional links. Logic-side signals connect directly to a UART controller, while the driver outputs and receiver inputs connect to the external RS-232 connector. The 16-pin SOIC package is suitable for conventional surface-mount PCB assembly, although connector protection, grounding, and signal-integrity practices remain necessary in industrial environments.
Typical uses include industrial serial controllers, programmable logic controller communication ports, data-acquisition equipment, point-of-sale terminals, and service interfaces for embedded systems. A dual-driver, dual-receiver arrangement is particularly useful when a board must exchange commands and status data with a single RS-232 port or interface two separate RS-232 links.
Design the circuit around the manufacturer's recommended 0.1uF charge-pump capacitor network and observe polarity and routing requirements shown in the MAX3232 data sheet. Keep sensitive receiver traces away from switching nodes and high-current edges, provide a stable ground reference between the logic board and RS-232 equipment, and consider external transient protection for cables longer than a short bench connection.
This product overview combines interface specifications, pin-level implementation guidance, application patterns, and verified drop-in alternatives to accelerate component selection and PCB design. It also identifies the electrical and qualification checks that must be completed before substituting one RS-232 transceiver for another.
Alternativas drop-in para MAX3232CSE+TG1Z — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MAX3232CSE+TG1Z (mesmo formato e footprint) — diferindo em Maximum Data Rate, Package, Interface Standard, Supply Voltage Range, Device Type.
MAX3232CSE+
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3232ECUE+T
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3232ESE+
✅ Drop-InConsulte o preço
Ver ficha técnica →MAX3232CSE+TG1Z Especificações
| Product Type | Dual RS-232 transceiver with 2 transmitters and 2 receivers |
| Supply Voltage Range | 3.0V to 5.5V |
| Maximum Data Rate | 1Mbps |
| Interface Standard | True RS-232 |
| Number of Drivers | 2 |
| Number of Receivers | 2 |
| Charge-Pump Capacitors | 4 x 0.1uF |
| Encapsulamento | 16-pin SOIC |
| Tipo de montagem | Surface Mount |
| Logic-Side Supply | Single positive supply |
| Production Status | Production |
Configuração de pinos do MAX3232CSE+TG1Z
| Pino 1 | C1+ — Charge-pump capacitor terminal |
| Pino 2 | V+ — Charge-pump output capacitor terminal |
| Pino 3 | C1- — Charge-pump capacitor terminal |
| Pino 4 | C2+ — Charge-pump capacitor terminal |
| Pino 5 | C2- — Charge-pump capacitor terminal |
| Pino 6 | V- — Charge-pump output capacitor terminal |
| Pino 7 | T1OUT — First RS-232 transmitter output |
| Pino 8 | R1IN — First RS-232 receiver input |
| Pino 9 | R1OUT — First receiver logic output |
| Pino 10 | R2IN — Second RS-232 receiver input |
| Pino 11 | T2IN — Second transmitter logic input |
| Pino 12 | T2OUT — Second RS-232 transmitter output |
| Pino 13 | R2OUT — Second receiver logic output |
| Pino 14 | T1IN — First transmitter logic input |
| Pino 15 | GND — Ground |
| Pino 16 | VCC — Positive supply |
Aplicações típicas
MAX3232CSE+TG1Z é adequado para 6 aplicaçãos: Industrial PLC Serial Communication, Data Acquisition Equipment, Point-of-Sale Terminal Interface, Embedded Service and Configuration Port, Two-Port RS-232 Interface Expansion, Programmable Logic Controller Communication.
Industrial PLC Serial Communication
The MAX3232CSE+TG1Z fits a PLC or serial gateway that must communicate with RS-232 equipment over a 3.0V to 5.5V supply. Its two transmitters and two receivers support bidirectional command and status traffic, while the 1Mbps capability allows the interface to exceed the speed of many conventional serial-control links. Four 0.1uF charge-pump capacitors implement the true RS-232 voltage conversion. Place the interface close to the connector, maintain a common ground reference, and add cable-side surge protection when the port connects to external industrial wiring.
Recomendado
Data Acquisition Equipment
The MAX3232CSE+TG1Z is useful in laboratory and industrial data-acquisition equipment that exchanges commands and measurements with a host computer. A single 3.3V or 5V supply powers both the logic system and the RS-232 interface, avoiding a separate negative rail for the transmitters. The dual-driver and dual-receiver arrangement can support one full-duplex port or two independent links. Its maximum data rate of 1Mbps is suitable for command traffic and burst-oriented measurements, while the four required 0.1uF capacitors should be placed according to the reference circuit.
Recomendado
Point-of-Sale Terminal Interface
The MAX3232CSE+TG1Z can connect a point-of-sale controller, receipt printer, or service terminal to an RS-232 peripheral. Its true RS-232 levels support legacy equipment without adding a separate negative power rail, and its 3.0V to 5.5V operating range accommodates embedded processors operating at either common logic voltage. The two transmitter and two receiver channels provide flexible command and status routing. Because retail peripherals may use long cables, place protection at the connector and keep the logic-side ground reference close to the transceiver to minimize noise pickup.
Recomendado
Embedded Service and Configuration Port
The MAX3232CSE+TG1Z provides a compact service port for an embedded controller, programmable logic controller, or field-programmable gate array that requires configuration and diagnostic access. The 16-pin SOIC package preserves PCB area, while the integrated dual charge pump generates true RS-232 levels from one positive supply. Its two transmitters and receivers can handle both console commands and peripheral status. Follow the data-sheet capacitor layout closely, avoid routing the charge-pump nodes beneath sensitive signal paths, and use a series resistor or protection network where exposed cables enter the enclosure.
Recomendado
Two-Port RS-232 Interface Expansion
The MAX3232CSE+TG1Z can expand one host into two separate RS-232 links because it contains two independent transmitters and two receivers. This arrangement suits instrumentation with one command channel and one status channel, or systems that connect two different peripherals through one interface IC. The device operates from 3.0V to 5.5V and supports rates up to 1Mbps, providing performance above ordinary low-speed RS-232 use. Assign each channel according to the pin-description table, maintain consistent signal grounding, and route each cable-side interface through appropriate transient protection.
Recomendado
Programmable Logic Controller Communication
The MAX3232CSE+TG1Z is appropriate for PLC communication modules that connect logic-level controller hardware to RS-232 drives, HMIs, or service equipment. Its 3.0V to 5.5V supply range allows integration with common embedded control platforms, and the 1Mbps maximum data rate supports efficient command exchanges. The dual-channel arrangement can reduce the number of interface components on a control board. Observe the recommended 0.1uF charge-pump capacitor placement, provide continuous ground near the device, and isolate external cable transients from sensitive controller circuitry.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MAX3232CSE+TG1Z — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MAX3232CSE+ | MAX3232ECUE+T | MAX3232ESE+ |
|---|---|---|---|---|
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Transmitter and Receiver Count | 2 transmitters and 2 receivers | 2 transmitters and 2 receivers | 2 transmitters and 2 receivers | 2 transmitters and 2 receivers |
| Interface Standard | True RS-232 | True RS-232 | RS-232 | RS-232 |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount | Surface Mount |
Principais diferenciais
- Single-supply true RS-232 operation (vs MAX3232ECUE+T)
- Two transmitters and two receivers in a compact package (vs MAX3232ESE+)
- No external negative supply requirement (vs MAX3232CSE+)
Notas de projeto
Place the four 0.1uF charge-pump capacitors close to their corresponding C1+, C1-, C2+, C2-, V+, and V- pins, and minimize loop area. Follow the pin and polarity arrangement in the Analog Devices MAX3232 Data Sheet (Rev. 10). Short, direct connections reduce switching transients coupled into receiver inputs, especially when the interface sits beside clocks, processors, or high-speed memory.
Keep RS-232 driver outputs and receiver inputs away from the charge-pump nodes and unrelated high-current switching paths. Route the ground return with a low-impedance path and maintain a common reference between the logic ground and connected RS-232 equipment. When a cable leaves the enclosure, place the protection network near the connector so transient current is diverted before it reaches the transceiver.
Do not substitute an RS-232 receiver-only or driver-only IC without redesigning the board, and do not treat every 16-pin RS-232 transceiver as automatically interchangeable. Verify the complete pinout, logic input thresholds, receiver input range, temperature grade, charge-pump capacitor arrangement, and shutdown behavior. Also confirm that UART signal polarity and timing remain compatible with the connected equipment.
Informações de conformidade
The manufacturer product page identifies the MAX3232 family as being in production, but no specific compliance declaration for this exact ordering code was identified. Confirm the current material and environmental declarations before a regulated production release.