MC14585BD - 4-Bit CMOS Magnitude Comparator | onsemi
N.º da peça: MC14585BD ✓ AtivoMC14585BD Visão geral
A magnitude comparator is a digital logic IC that determines the relative order of two binary numbers. Its outputs encode the mathematical relationships A<B, A=B, and A>B, making the comparator a fundamental building block in arithmetic control, sorting, address decoding, test equipment, and digital control systems. The MC14585BD belongs to the CMOS logic family and uses complementary MOS enhancement-mode devices, providing a direct alternative to TTL implementations when system-level logic is already based on CMOS supply rails.
The principal features of the MC14585BD are its eight data inputs, three cascade inputs, three active-high comparison outputs, 4-bit comparison width, and 16-pin SOIC format. The cascade inputs allow a more significant 4-bit section to determine the result when lower-order sections are equal. This architecture supports cascaded comparisons for 8-bit, 12-bit, 16-bit, and larger data paths when the corresponding logic states are properly connected.
The MC14585BD is intended for conventional CMOS digital systems in which logic thresholds, supply voltage, noise immunity, and propagation delay must be checked against the actual design operating conditions. Because the available manufacturer datasheet identifies the circuit as a CMOS enhancement-mode implementation but does not expose complete electrical-limit tables in the search excerpt, detailed voltage, current, timing, and temperature ratings remain marked where necessary rather than estimated.
Typical uses include binary number ordering, digital test fixtures, arithmetic-controller address selection, industrial control logic, embedded comparison functions, and cascading multi-section comparisons. The active-high A<B, A=B, and A>B outputs can feed counters, multiplexers, control-state machines, display logic, or interrupt and status signals in a larger digital system.
PCB layout should preserve short input and output traces, provide a solid ground reference, and decouple the power supply near the device. When cascading comparators, route the cascade outputs from the least-significant section into the most-significant section and confirm timing at the system level. The manufacturer datasheet pin-description table should be used as the authority when assigning tracks and probing the 16-pin footprint.
This page organizes the manufacturer function description, pin map, verified package information, qualified drop-in comparisons, application guidance, and practical implementation notes. It is designed to help engineers move quickly from device identification to schematic review and PCB-level design decisions while keeping unresolved electrical details explicit.
Alternativas drop-in para MC14585BD — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
MC14585B
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
CD4585BNSR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
CD4585BNSRE4
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MC14585BD Classificações máximas e características elétricas
| Comparator Type | 4-bit magnitude comparator |
| Logic Technology | CMOS |
| Transistor Construction | Complementary MOS enhancement-mode devices |
| Comparison Data Inputs | 8 inputs |
| Data Input Designation | A3-A0 and B3-B0 |
| Cascading Inputs | 3 inputs |
| Cascading Input Designation | A<B, A=B, and A>B |
| Comparison Outputs | 3 outputs |
| Output Designation | A<B, A=B, and A>B |
| Output Logic Level | Active high |
| Encapsulamento | 16-pin SOIC |
| Tipo de montagem | Surface mount |
| Contagem de pinos | 16 pins |
| RoHS Compliance | unknown |
| REACH Compliance | unknown |
Configuração de pinos do MC14585BD
| Pino 1 | A0 — Least-significant A-side comparison input |
| Pino 2 | B0 — Least-significant B-side comparison input |
| Pino 3 | A1 — A1 comparison input |
| Pino 4 | B1 — B1 comparison input |
| Pino 5 | A2 — A2 comparison input |
| Pino 6 | B2 — B2 comparison input |
| Pino 7 | A3 — Most-significant A-side comparison input |
| Pino 8 | B3 — Most-significant B-side comparison input |
| Pino 9 | A<B — Active-high output indicating A is less than B |
| Pino 10 | A=B — Active-high output indicating A is equal to B |
| Pino 11 | A>B — Active-high output indicating A is greater than B |
| Pino 12 | A<B — Cascading input for A-is-less-than-B condition |
| Pino 13 | A=B — Cascading input for A-is-equal-to-B condition |
| Pino 14 | A>B — Cascading input for A-is-greater-than-B condition |
| Pino 15 | VSS — Ground reference |
| Pino 16 | VDD — Positive supply voltage |
Aplicações típicas
MC14585BD é adequado para 6 aplicaçãos: 4-Bit Address Comparison, Binary Number Sorting Control, Industrial Range and Limit Detection, Arithmetic Control and Equality Detection, Digital Test and Measurement Logic, Multi-Section Cascaded Bus Comparison.
4-Bit Address Comparison
The MC14585BD suits address-selection logic because it compares the A3–A0 and B3–B0 buses and asserts active-high A<B, A=B, and A>B outputs. A decoded address can be placed on one input group while a threshold or register address is applied to the other, allowing equality detection without a separate gate network. The 16-pin SOIC package also keeps the comparator compact where several control channels are distributed across a board. In a synchronous system, the address and threshold must remain stable for the comparator’s propagation interval before the result is sampled. The equal output can trigger a register update, interrupt request, or memory-enable signal, while the less-than and greater-than outputs can support range policies. Final timing verification should use the electrical characteristics in the onsemi MC14585B datasheet.
Recomendado
Binary Number Sorting Control
The MC14585BD can provide the ordering decision required by simple binary sorting and ranking control circuits. By applying two candidate values to A3–A0 and B3–B0, the active-high outputs immediately identify their relative relationship, allowing a controller to determine which value should advance, swap, or update a register. The part is most appropriate for low-width words where a dedicated wider comparator is unnecessary. Cascading permits multiple 4-bit sections to determine the result across a larger bus. Timing paths should be reviewed for comparator delay, cascade delay, and downstream controller input requirements. The three distinct outputs are more useful than a single equality signal because sorting logic often needs separate less-than, equal, and greater-than decisions.
Recomendado
Industrial Range and Limit Detection
The MC14585BD is useful for industrial control logic that must detect whether a 4-bit command, setpoint, or status value lies below, at, or above a defined limit. Feeding the measured value to A3–A0 and the programmed limit to B3–B0 produces three unambiguous active-high decisions that can be routed into relay-control, alarm, or interlock logic. For dependable operation, inputs should remain within valid logic levels and the surrounding controller should account for propagation delay before changing a safety-relevant state. The onsemi datasheet should be consulted for exact voltage and temperature limits before industrial deployment. Because this device performs binary comparison rather than analog thresholding, the analog signal must first be converted into a digital representation.
Recomendado
Arithmetic Control and Equality Detection
The MC14585BD fits arithmetic-control blocks that require equality or ordering information between two 4-bit operands. Its A=B output can indicate a zero-result condition after an arithmetic stage, while A<B and A>B identify the direction of a comparison for carry, increment, decrement, or conditional-transfer decisions. Using dedicated comparison outputs can simplify control equations and reduce the number of discrete gates around an adder. Cascaded sections support wider operand comparisons when the lower-order bits are equal. The implementation must prevent input transitions from creating false comparator results when values change near a decision boundary; registering the operands or allowing the required settling time are common methods. Exact timing margins should be calculated from the manufacturer’s propagation-delay data.
Recomendado
Digital Test and Measurement Logic
The MC14585BD can support digital test fixtures, pattern-generation systems, and instrumentation that must verify whether two 4-bit fields are equal or ordered. Applying expected and measured words to the comparator produces separate outputs that simplify error classification and diagnostic routing. Its three active-high comparison results can drive indicator logic, capture enables, or a supervisory controller. In test equipment, minimize loading at the compared nodes and ensure that the selected source devices maintain valid levels during acquisition. The small 16-pin SOIC footprint is useful in multi-channel fixture boards where several comparisons are required. Before using the comparator at high test rates, verify propagation delay and output transition behavior against the complete manufacturer electrical tables.
Recomendado
Multi-Section Cascaded Bus Comparison
The MC14585BD can be cascaded to compare wide binary buses by comparing low-order 4-bit sections first and forwarding their A<B, A=B, and A>B cascade states into more significant sections. The architecture is useful in wide control words, status registers, and multi-byte numeric fields where a single 4-bit comparison would be insufficient. Each stage adds its own propagation delay, so the most-significant section must not be sampled until both the local comparison and upstream cascade path are settled. PCB routing should minimize loading and crosstalk around these decision nets. The manufacturer datasheet identifies the three cascade inputs explicitly and should be used to verify the recommended connection arrangement and timing assumptions.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MC14585BD — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MC14585B | CD4585BNSR | CD4585BNSRE4 |
|---|---|---|---|---|
| Brand | onsemi | onsemi | Texas Instruments | Texas Instruments |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Function | 4-bit magnitude comparator | 4-bit magnitude comparator | 4-bit logic comparator | 4-bit logic comparator |
Principais diferenciais
- Direct three-way ordering result (vs CD4585BNSR)
- Native multi-section expansion (vs CD4585BNSRE4)
- Compact 16-pin integration (vs MC14585B)
Notas de projeto
Place the MC14585BD close to the logic that drives A3–A0 and B3–B0 and to the circuits that consume the A<B, A=B, and A>B outputs. Keep the 16-pin SOIC footprint free of unintended copper or mask openings, and use a continuous ground reference beneath the device where the board stack-up permits. A short supply trace and local bypass capacitor help maintain stable switching behavior, but capacitor selection and placement should follow the guidance in the manufacturer datasheet.
Do not sample the comparison outputs until the input and cascade paths have had sufficient time to settle. For cascaded comparisons, the most-significant section can receive both local data and delayed upstream decisions, so the total system propagation interval may be longer than one section. Confirm the timing against the manufacturer’s specified load and supply conditions, and register outputs before feeding them into a high-speed state machine when the available timing margin is limited.
A common integration error is to assume that the three active-high outputs are interchangeable cascade signals. The A<B, A=B, and A>B functions exist separately on the comparison outputs and cascade inputs, and each must connect to its corresponding logic function. Also avoid combining a comparator intended for 4-bit CMOS levels with a system operating at an incompatible voltage. Verify supply limits, logic thresholds, propagation delay, and output drive from the complete manufacturer datasheet before substituting another family member.
Informações de conformidade
The manufacturer search excerpt identifies CMOS construction but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because MC14585BD is not identified as an automotive-qualified device.