onsemi

MC14585BD - 4-Bit CMOS Magnitude Comparator | onsemi

MPN: MC14585BD ✓ نشط
16-pin SOIC Package
الحد الأدنى للطلب: 1 |

MC14585BD نظرة عامة

The onsemi MC14585BD is a 4-bit CMOS magnitude comparator in a 16-pin SOIC package. It compares two 4-bit binary words presented at inputs A3–A0 and B3–B0, then indicates whether A is less than, equal to, or greater than B through three active-high outputs. The device also provides three cascading inputs so multiple 4-bit sections can be expanded into wider comparison functions without adding a separate priority encoder or equality logic.

A magnitude comparator is a digital logic IC that determines the relative order of two binary numbers. Its outputs encode the mathematical relationships A<B, A=B, and A>B, making the comparator a fundamental building block in arithmetic control, sorting, address decoding, test equipment, and digital control systems. The MC14585BD belongs to the CMOS logic family and uses complementary MOS enhancement-mode devices, providing a direct alternative to TTL implementations when system-level logic is already based on CMOS supply rails.

The principal features of the MC14585BD are its eight data inputs, three cascade inputs, three active-high comparison outputs, 4-bit comparison width, and 16-pin SOIC format. The cascade inputs allow a more significant 4-bit section to determine the result when lower-order sections are equal. This architecture supports cascaded comparisons for 8-bit, 12-bit, 16-bit, and larger data paths when the corresponding logic states are properly connected.

The MC14585BD is intended for conventional CMOS digital systems in which logic thresholds, supply voltage, noise immunity, and propagation delay must be checked against the actual design operating conditions. Because the available manufacturer datasheet identifies the circuit as a CMOS enhancement-mode implementation but does not expose complete electrical-limit tables in the search excerpt, detailed voltage, current, timing, and temperature ratings remain marked where necessary rather than estimated.

Typical uses include binary number ordering, digital test fixtures, arithmetic-controller address selection, industrial control logic, embedded comparison functions, and cascading multi-section comparisons. The active-high A<B, A=B, and A>B outputs can feed counters, multiplexers, control-state machines, display logic, or interrupt and status signals in a larger digital system.

PCB layout should preserve short input and output traces, provide a solid ground reference, and decouple the power supply near the device. When cascading comparators, route the cascade outputs from the least-significant section into the most-significant section and confirm timing at the system level. The manufacturer datasheet pin-description table should be used as the authority when assigning tracks and probing the 16-pin footprint.

This page organizes the manufacturer function description, pin map, verified package information, qualified drop-in comparisons, application guidance, and practical implementation notes. It is designed to help engineers move quickly from device identification to schematic review and PCB-level design decisions while keeping unresolved electrical details explicit.

بدائل مباشرة لـ MC14585BD — نفس الحزمة، متوافق دبوس بدبوس. تُستثنى القطع ذات الحزم المختلفة التي تتطلب تعديل PCB.

MC14585B

✅ بديل مباشر ⚠️ مواصفات غير مُتحقق منها
📦 16-pin SOIC
Same onsemi 4-bit CMOS magnitude-comparator family and 16-pin SOIC architecture; device-specific ordering, lifecycle, and electrical details require comparison

📋 بديل مرجعي (غير موجود في الكتالوج)

CD4585BNSR

✅ بديل مباشر
📦 16-pin SOIC
Same 4-bit logic-comparator function and 16-pin SOIC class; supply voltage, timing, temperature range, and qualification must be cross-checked

📋 بديل مرجعي (غير موجود في الكتالوج)

CD4585BNSRE4

✅ بديل مباشر
📦 16-pin SOIC
Same 4-bit logic-comparator function and 16-pin SOIC class as CD4585BNSR, distinguished by ordering qualification rather than a different package

📋 بديل مرجعي (غير موجود في الكتالوج)

MC14585BD الحدود القصوى والخصائص الكهربائية

Comparator Type 4-bit magnitude comparator
Logic Technology CMOS
Transistor Construction Complementary MOS enhancement-mode devices
Comparison Data Inputs 8 inputs
Data Input Designation A3-A0 and B3-B0
Cascading Inputs 3 inputs
Cascading Input Designation A<B, A=B, and A>B
Comparison Outputs 3 outputs
Output Designation A<B, A=B, and A>B
Output Logic Level Active high
العلبة 16-pin SOIC
نوع التركيب Surface mount
عدد الأطراف 16 pins
RoHS Compliance unknown
REACH Compliance unknown

تكوين أطراف MC14585BD

SOIC-16 Package Pinout Diagram SOIC-16 16-pin, 3.9x9.9mm, P1.27mm, JEDEC MS-012. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 SOIC-16
دبوس 1 A0 — Least-significant A-side comparison input
دبوس 2 B0 — Least-significant B-side comparison input
دبوس 3 A1 — A1 comparison input
دبوس 4 B1 — B1 comparison input
دبوس 5 A2 — A2 comparison input
دبوس 6 B2 — B2 comparison input
دبوس 7 A3 — Most-significant A-side comparison input
دبوس 8 B3 — Most-significant B-side comparison input
دبوس 9 A<B — Active-high output indicating A is less than B
دبوس 10 A=B — Active-high output indicating A is equal to B
دبوس 11 A>B — Active-high output indicating A is greater than B
دبوس 12 A<B — Cascading input for A-is-less-than-B condition
دبوس 13 A=B — Cascading input for A-is-equal-to-B condition
دبوس 14 A>B — Cascading input for A-is-greater-than-B condition
دبوس 15 VSS — Ground reference
دبوس 16 VDD — Positive supply voltage

التطبيقات النموذجية

MC14585BD مناسب لـ 6 التطبيقs: 4-Bit Address Comparison, Binary Number Sorting Control, Industrial Range and Limit Detection, Arithmetic Control and Equality Detection, Digital Test and Measurement Logic, Multi-Section Cascaded Bus Comparison.

🖥️

4-Bit Address Comparison

The MC14585BD suits address-selection logic because it compares the A3–A0 and B3–B0 buses and asserts active-high A<B, A=B, and A>B outputs. A decoded address can be placed on one input group while a threshold or register address is applied to the other, allowing equality detection without a separate gate network. The 16-pin SOIC package also keeps the comparator compact where several control channels are distributed across a board. In a synchronous system, the address and threshold must remain stable for the comparator’s propagation interval before the result is sampled. The equal output can trigger a register update, interrupt request, or memory-enable signal, while the less-than and greater-than outputs can support range policies. Final timing verification should use the electrical characteristics in the onsemi MC14585B datasheet.

🔧

Binary Number Sorting Control

The MC14585BD can provide the ordering decision required by simple binary sorting and ranking control circuits. By applying two candidate values to A3–A0 and B3–B0, the active-high outputs immediately identify their relative relationship, allowing a controller to determine which value should advance, swap, or update a register. The part is most appropriate for low-width words where a dedicated wider comparator is unnecessary. Cascading permits multiple 4-bit sections to determine the result across a larger bus. Timing paths should be reviewed for comparator delay, cascade delay, and downstream controller input requirements. The three distinct outputs are more useful than a single equality signal because sorting logic often needs separate less-than, equal, and greater-than decisions.

🏭

Industrial Range and Limit Detection

The MC14585BD is useful for industrial control logic that must detect whether a 4-bit command, setpoint, or status value lies below, at, or above a defined limit. Feeding the measured value to A3–A0 and the programmed limit to B3–B0 produces three unambiguous active-high decisions that can be routed into relay-control, alarm, or interlock logic. For dependable operation, inputs should remain within valid logic levels and the surrounding controller should account for propagation delay before changing a safety-relevant state. The onsemi datasheet should be consulted for exact voltage and temperature limits before industrial deployment. Because this device performs binary comparison rather than analog thresholding, the analog signal must first be converted into a digital representation.

🧩

Arithmetic Control and Equality Detection

The MC14585BD fits arithmetic-control blocks that require equality or ordering information between two 4-bit operands. Its A=B output can indicate a zero-result condition after an arithmetic stage, while A<B and A>B identify the direction of a comparison for carry, increment, decrement, or conditional-transfer decisions. Using dedicated comparison outputs can simplify control equations and reduce the number of discrete gates around an adder. Cascaded sections support wider operand comparisons when the lower-order bits are equal. The implementation must prevent input transitions from creating false comparator results when values change near a decision boundary; registering the operands or allowing the required settling time are common methods. Exact timing margins should be calculated from the manufacturer’s propagation-delay data.

🧪

Digital Test and Measurement Logic

The MC14585BD can support digital test fixtures, pattern-generation systems, and instrumentation that must verify whether two 4-bit fields are equal or ordered. Applying expected and measured words to the comparator produces separate outputs that simplify error classification and diagnostic routing. Its three active-high comparison results can drive indicator logic, capture enables, or a supervisory controller. In test equipment, minimize loading at the compared nodes and ensure that the selected source devices maintain valid levels during acquisition. The small 16-pin SOIC footprint is useful in multi-channel fixture boards where several comparisons are required. Before using the comparator at high test rates, verify propagation delay and output transition behavior against the complete manufacturer electrical tables.

🔗

Multi-Section Cascaded Bus Comparison

The MC14585BD can be cascaded to compare wide binary buses by comparing low-order 4-bit sections first and forwarding their A<B, A=B, and A>B cascade states into more significant sections. The architecture is useful in wide control words, status registers, and multi-byte numeric fields where a single 4-bit comparison would be insufficient. Each stage adds its own propagation delay, so the most-significant section must not be sampled until both the local comparison and upstream cascade path are settled. PCB routing should minimize loading and crosstalk around these decision nets. The manufacturer datasheet identifies the three cascade inputs explicitly and should be used to verify the recommended connection arrangement and timing assumptions.

ملخص المنتجات الموصى بها

MC14585BD onsemi يُستخدم في: 4-Bit Address Comparison, Binary Number Sorting Control, Industrial Range and Limit Detection, Arithmetic Control and Equality Detection, Digital Test and Measurement Logic, Multi-Section Cascaded Bus Comparison MC14585B Related onsemi magnitude-comparator family يُستخدم في: 4-Bit Address Comparison, Industrial Range and Limit Detection, Multi-Section Cascaded Bus Comparison CD4585BNSR Cross-brand comparator option يُستخدم في: Binary Number Sorting Control, Digital Test and Measurement Logic CD4585BNSRE4 Cross-brand 4-bit comparator candidate يُستخدم في: Arithmetic Control and Equality Detection
What is the MC14585BD?
The MC14585BD is a 4-bit CMOS magnitude comparator that compares two 4-bit binary words and produces active-high A<B, A=B, and A>B outputs. According to the onsemi MC14585B datasheet, the circuit is constructed with complementary MOS enhancement-mode devices and includes eight comparison inputs, three cascading inputs, and three comparison outputs in a 16-pin SOIC package.
How many bits can the MC14585BD compare?
The MC14585BD compares two 4-bit binary values per device section. Its A3–A0 inputs accept one word, while B3–B0 accept the other, and the outputs indicate whether A is less than, equal to, or greater than B. The onsemi MC14585B datasheet also identifies three cascade inputs, allowing additional sections to extend comparison to wider buses.
Where can I download the MC14585BD datasheet PDF?
The official MC14585BD datasheet is available from onsemi at https://www.onsemi.com/pdf/datasheet/mc14585b-d.pdf. It is the appropriate document for the pin-description table, logic diagram, cascade configuration, operating limits, and electrical characteristics. Use the manufacturer PDF rather than relying on secondary summaries when assigning PCB nets or checking propagation timing.
Where can I find the MC14585BD pinout?
The MC14585BD uses a 16-pin SOIC footprint, with pin 1 located at the standard top-left position of the SOIC package. The manufacturer pin-description table identifies data inputs A0–A3 and B0–B3, three cascade inputs, the corresponding A<B, A=B, and A>B outputs, and the two supply pins. Cross-check every connection against the MC14585B datasheet before fabrication.
Can the MC14585BD outputs be used to compare an address with a threshold?
Yes. Connect the address bus to A3–A0 and the threshold to B3–B0, then use the active-high equality output to identify an exact match. The less-than and greater-than outputs can support range selection or control decisions. Account for propagation delay in synchronous address-decoding systems so downstream logic samples the comparator result only after it is valid.
How do I cascade MC14585BD sections for an 8-bit comparison?
An 8-bit comparison can be built from two MC14585BD sections. Compare the least-significant 4-bit halves first and connect their A<B, A=B, and A>B cascade signals to the corresponding cascade inputs of the most-significant section. The final section then determines the overall 8-bit relationship. The onsemi datasheet identifies these as A<B, A=B, and A>B cascading inputs.
What is the difference between MC14585BD and CD4585BNSR?
The MC14585BD is an onsemi 4-bit CMOS magnitude comparator in a 16-pin SOIC, while CD4585BNSR is a Texas Instruments comparator identified in the cross-reference results as a logic magnitude comparator. Both perform the same core 4-bit ordering function, but electrical timing, supply limits, temperature coverage, and lifecycle conditions must be checked in each manufacturer datasheet before interchange.
Is CD4585BNSR a drop-in replacement for MC14585BD?
CD4585BNSR is the closest qualified cross-brand candidate because it is identified as a 4-bit logic magnitude comparator and uses the same 16-pin SOIC class. Treat it as a board-level replacement candidate rather than an unconditional substitution: verify pin functions, supply-voltage range, propagation timing, output behavior, temperature grade, and lifecycle status against both datasheets before production release.
When should I choose the MC14585BD instead of CD4585BNSR?
Choose the MC14585BD when its onsemi electrical characteristics, qualification history, and ongoing device documentation are specifically required for the design. CD4585BNSR may be appropriate when procurement needs a second source with the same 16-pin SOIC architecture. The decision should be based on matching supply voltage, propagation delay, output levels, temperature range, and qualification requirements rather than function name alone.
What can replace the MC14585BD?
CD4585BNSR is the identified cross-brand replacement candidate, and MC14585B is the related onsemi family designation. A true drop-in decision requires the same 16-pin SOIC footprint, matching A0–A3 and B0–B3 data inputs, matching cascade and comparison outputs, and compatible voltage and timing characteristics. Review both manufacturer datasheets before changing the approved BOM.
Is MC14585BD suitable for industrial control logic?
The MC14585BD is suitable for digital control functions that compare 4-bit values, including counters, state machines, range checks, and address-selection logic. Its CMOS construction and three active-high outputs fit conventional digital designs. Industrial suitability should be confirmed against the complete electrical ratings, operating-temperature limits, ESD qualifications, and system reliability requirements listed in the manufacturer datasheet.
How much power does the MC14585BD consume?
The MC14585BD is a CMOS 4-bit magnitude comparator, but a definitive operating-power figure cannot be stated without its complete supply-voltage and input-transition characteristics. Use the manufacturer datasheet for quiescent current, dynamic current, and supply-current limits. At the circuit level, power depends on the selected supply voltage and the rate at which the eight data inputs and three cascade inputs change state.
What are the key specifications of MC14585BD that engineers should know?
The key MC14585BD specifications are its 4-bit comparison width, eight data inputs, three cascade inputs, three active-high outputs, CMOS enhancement-mode construction, and 16-pin SOIC package. These details define its role as a binary magnitude comparator. Supply voltage, timing, temperature, and current limits require consultation of the complete onsemi datasheet before the device is used in a finalized design.
Where can I buy MC14585BD online?
Use the Request a Quote form on this page to ask about MC14585BD availability, current pricing, order quantity, and delivery timing. The request can identify the exact 16-pin SOIC ordering code MC14585BD and any required production quantities. Current commercial terms should be confirmed through that form because inventory and lead time can change.
What is the price of MC14585BD?
Current MC14585BD pricing depends on order quantity, shipment configuration, and market availability, so it should not be inferred from a generic device listing. Submit the exact MPN MC14585BD through the Request a Quote form on this page. The quotation process provides pricing for the requested quantity and packaging without relying on a potentially stale list price.
What is the lead time and stock status for MC14585BD?
Stock and lead time for MC14585BD should be confirmed through the Request a Quote form on this page. Include the required quantity, target delivery date, and whether production or prototype quantities are needed. Because component availability can vary by lot, authorized channel, and order configuration, the quotation response is the appropriate source for current scheduling information.
Is MC14585BD RoHS compliant and suitable for lead-free assembly?
RoHS and lead-free status cannot be confirmed from the product search excerpt alone. Consult the current onsemi product page, material declarations, and applicable compliance documentation for MC14585BD before treating the device as qualified for lead-free assembly. The absence of a stated certification in the search result should not be interpreted either as compliance or noncompliance.

بيانات مرجعية هندسية لـ MC14585BD — المقارنة وإرشادات التصميم ومعلومات الامتثال.

دليل الاختيار

Choose MC14585BD when a design needs a dedicated 4-bit CMOS magnitude comparator with separate active-high A<B, A=B, and A>B outputs in a 16-pin SOIC package. Its three cascade inputs are especially useful when a wider bus must be compared by connecting successive 4-bit sections. MC14585B is the related onsemi family designation and should be selected only after confirming the exact ordering code and electrical conditions. Consider CD4585BNSR or CD4585BNSRE4 when a second source is needed for the same 4-bit comparator architecture and 16-pin SOIC footprint. Treat either Texas Instruments candidate as a qualified alternative only after checking supply voltage, propagation delay, logic thresholds, temperature range, and lifecycle status against the complete datasheets. The MC14585BD is preferable when the onsemi device is the approved BOM standard or its qualification and documentation meet the product program’s requirements.

المقارنة مع البدائل

المعامل هذا المنتج MC14585B CD4585BNSR CD4585BNSRE4
Brand onsemi onsemi Texas Instruments Texas Instruments
Package 16-pin SOIC 16-pin SOIC 16-pin SOIC 16-pin SOIC
Function 4-bit magnitude comparator 4-bit magnitude comparator 4-bit logic comparator 4-bit logic comparator

أبرز الفروقات

  • Direct three-way ordering result (مقابلCD4585BNSR)
  • Native multi-section expansion (مقابلCD4585BNSRE4)
  • Compact 16-pin integration (مقابلMC14585B)

ملاحظات التصميم

Place the MC14585BD close to the logic that drives A3–A0 and B3–B0 and to the circuits that consume the A<B, A=B, and A>B outputs. Keep the 16-pin SOIC footprint free of unintended copper or mask openings, and use a continuous ground reference beneath the device where the board stack-up permits. A short supply trace and local bypass capacitor help maintain stable switching behavior, but capacitor selection and placement should follow the guidance in the manufacturer datasheet.

Do not sample the comparison outputs until the input and cascade paths have had sufficient time to settle. For cascaded comparisons, the most-significant section can receive both local data and delayed upstream decisions, so the total system propagation interval may be longer than one section. Confirm the timing against the manufacturer’s specified load and supply conditions, and register outputs before feeding them into a high-speed state machine when the available timing margin is limited.

A common integration error is to assume that the three active-high outputs are interchangeable cascade signals. The A<B, A=B, and A>B functions exist separately on the comparison outputs and cascade inputs, and each must connect to its corresponding logic function. Also avoid combining a comparator intended for 4-bit CMOS levels with a system operating at an incompatible voltage. Verify supply limits, logic thresholds, propagation delay, and output drive from the complete manufacturer datasheet before substituting another family member.

معلومات الامتثال

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
خالٍ من الرصاص
Unknown
خالٍ من الهالوجين
Unknown
المعادن المتنازع عليها
Unknown

The manufacturer search excerpt identifies CMOS construction but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because MC14585BD is not identified as an automotive-qualified device.

تم التحقق من البيانات في: 2026-11-11 — تم التحقق من البيانات وتنسيقها بواسطة فريق هندسة المكونات في XAIPART

عمليات بحث ذات صلة

MC14585BD datasheet MC14585BD pinout MC14585BD datasheet pdf MC14585BD equivalent MC14585BD replacement MC14585BD cross reference MC14585BD vs CD4585BNSR MC14585BD footprint MC14585BD application circuit onsemi MC14585BD MC14585BD price MC14585BD stock MC14585B magnitude comparator 16-SOIC magnitude comparator 4-bit CMOS magnitude comparator

المكونات والمصطلحات ذات الصلة

onsemi MC14585BD MC14585B CD4585BNSR CD4585BNSRE4 Texas Instruments magnitude comparator 4-bit magnitude comparator CMOS logic complementary MOS enhancement-mode devices binary comparator digital logic IC logic comparator active-high output A<B output A=B output A>B output cascading input 16-pin SOIC SOIC package surface mount binary word digital control system address comparison
عرض سعر سريع RFQ
املأ التفاصيل الكاملة — سيرد فريق المبيعات لدينا خلال 24 ساعة
رقم القطعة الشركة المصنعة الحزمة QTY السعر المستهدف الإجمالي
✓
تم إرسال عرض السعر!

سنرد على بريدك الإلكتروني خلال 24 ساعة

1
تم إرسال طلب عرض السعر
2
تم استلام عرض السعر
3
تم تقديم الطلب
4
الدفع
5
تم الشحن
6
تم التسليم
عرض تفاصيل طلب عرض السعر