MCP6004-I/SL - Quad 1MHz R-R Op Amp | Microchip Technology
N.º da peça: MCP6004-I/SL ✓ AtivoMCP6004-I/SL Visão geral
An operational amplifier is an analog integrated circuit that amplifies the voltage difference between its non-inverting and inverting inputs. The MCP6004 belongs to the operational-amplifier hierarchy, where it sits below the general-purpose amplifier category and above the CMOS low-power amplifier class. Four amplifiers in one package make it useful for multi-channel analog systems where several low-frequency signals must be amplified, buffered, or filtered.
Rail-to-rail input allows the MCP6004 to accept signals close to either supply rail, while rail-to-rail output improves output-voltage range at light load. Its typical 1 MHz gain-bandwidth product supports general-purpose low-frequency signal paths. The typical 100 µA quiescent current also makes the device suitable for portable, battery-powered, and low-power sensor equipment when operating speed is not the primary requirement.
The MCP6004 family uses a CMOS-based operational-amplifier architecture optimized for low power and low cost. With four rail-to-rail amplifiers in one 14-lead SOIC, it reduces component count in designs requiring multiple channels. The operating voltage range of 1.8 V to 6 V supports systems built around low-voltage rails, although the selected amplifier must also satisfy required output swing, input common-mode range, noise, stability, and precision requirements.
Typical uses include sensor-signal conditioning, low-voltage data acquisition, audio input stages, general buffering, and four-channel filtering. In a sensor interface, the amplifier can increase the usable level of a low-amplitude transducer signal before conversion or control. In portable instrumentation, low quiescent current helps preserve battery life, while the four-channel package reduces board area.
Circuit design should account for the amplifier's gain-bandwidth limit and the stability requirements of the feedback network. Place input and output components close to the device, maintain the recommended bypass capacitance, and verify that source impedance, load capacitance, and noise gain do not compromise stability. The manufacturer datasheet should be used for the complete pin-description table and application limits.
This product page combines the manufacturer's operating-range and performance information with package details, practical application guidance, and verified drop-in replacement options. It also provides pin-focused search coverage and comparison parameters that help engineers evaluate the MCP6004-I/SL for low-voltage, low-power analog designs.
Alternativas drop-in para MCP6004-I/SL — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MCP6004-I/SL (mesmo formato e footprint) — diferindo em Package, Number of Channels, Amplifier Type, Supply Voltage Range, Input Common-Mode Range.
MCP6004-E/SL
✅ Drop-InConsulte o preço
Ver ficha técnica →MCP6004T-I/SL
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP6004-E/SLVAO
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP607-I/SN
✅ Drop-InConsulte o preço
Ver ficha técnica →LMV324IDT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
MCP6004-I/SL Classificações máximas e características elétricas
| Amplifier Type | Quad general-purpose operational amplifier |
| Number of Amplifiers | 4 circuits |
| Supply Voltage Range | 1.8 V to 6 V |
| Typical Gain-Bandwidth Product | 1 MHz |
| Typical Quiescent Current | 100 µA |
| Input Type | Rail-to-rail |
| Tipo de saída | Rail-to-rail |
| Technology | CMOS |
| Encapsulamento | 14-lead SOIC |
| Package Designator | SL |
| Faixa de temperatura de operação | -40 °C to +85 °C |
| Country of Origin | Thailand |
| Tipo de montagem | Surface mount |
| Número de pinos | 14 pins |
| Typical Phase Margin | 90° |
Guia de Configuração de Pinos do MCP6004-I/SL sl
Configuração de pinos para MCP6004-I/SL (pacote sl). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para MCP6004-I/SL.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MCP6004-I/SL é adequado para 6 aplicaçãos: Low-Voltage Sensor Signal Conditioning, Portable Data Acquisition, Audio Input Buffering, Industrial Control Interfaces, Active Filtering and Signal Conditioning, Low-Power Embedded Control.
Low-Voltage Sensor Signal Conditioning
The MCP6004-I/SL fits four-channel sensor interfaces that operate from 1.8 V to 6 V and require a compact, low-power amplification stage. Its rail-to-rail input capability helps preserve signals positioned near the supply rails, while the typical 100 µA quiescent current limits amplifier overhead in battery-powered systems. The four amplifiers can condition outputs from resistive, capacitive, or low-level transducer sensors before an ADC or controller samples them. Its 1 MHz typical gain-bandwidth product is sufficient for many low-frequency measurement paths, although sensor bandwidth, source impedance, and required closed-loop gain determine the final margin. Stable operation should be checked with the actual sensor impedance and filter network.
Recomendado
Portable Data Acquisition
MCP6004-I/SL is well suited to portable measurement systems requiring several analog channels without a large power budget. Its typical 100 µA quiescent current is valuable in instrument designs that operate from a 3.3 V or 5 V battery-derived rail, while rail-to-rail input and output operation increases usable signal span in low-voltage systems. Four independent channels can amplify sensor outputs, buffer ADC inputs, or form active analog filters. The 1 MHz gain-bandwidth product supports low-frequency acquisition signals rather than high-speed waveform capture, and system designers should include output-swing, capacitive-load, and stability checks. Proper bypassing close to the supply pins helps maintain predictable analog performance.
Recomendado
Audio Input Buffering
The MCP6004-I/SL can provide input buffering and gain stages for low-voltage audio or microphone circuits. Rail-to-rail input and output operation helps maintain signal headroom in portable equipment operating from 1.8 V to 6 V, while the typical 100 µA quiescent current supports battery-powered operation. The 1 MHz gain-bandwidth product is appropriate for voice-band and general audio paths, but users should evaluate noise, slew rate, output swing, and load impedance against their audio requirements. The four-channel package also supports a stereo implementation plus additional control or monitoring paths. A common-mode or differential input arrangement should be selected according to the source, and the manufacturer datasheet should guide gain and stability calculations.
Recomendado
Industrial Control Interfaces
MCP6004-I/SL is appropriate for low-level industrial interface circuits that process slow sensor and control signals. Its -40 °C to +85 °C specified temperature range covers many commercial and industrial environments, and four amplifiers allow multiple channels to share a compact 14-lead SOIC footprint. Rail-to-rail operation can improve conditioning of signals near the positive or negative rail in 3.3 V and 5 V systems. The amplifier is not intended for high-speed closed-loop servo loops at its 1 MHz typical gain-bandwidth product, so dynamic requirements must be checked. Input protection, filtering, grounding, and isolation should be handled at the interface boundary, while the amplifier provides the high-impedance gain and buffering stage.
Recomendado
Active Filtering and Signal Conditioning
MCP6004-I/SL can implement low-frequency active filters and general signal-conditioning blocks where four channels and low operating current are useful. Its typical 1 MHz gain-bandwidth product supports moderate-gain, low-frequency filter sections, while rail-to-rail input and output behavior can preserve signal range in low-voltage circuits. Each amplifier channel can be assigned to filtering, gain, active balancing, or buffering rather than requiring separate single-amplifier packages. Component tolerances, noise gain, and the operational-amplifier gain-bandwidth relationship must be considered when setting poles and Q. Capacitive loading and high source impedance can affect stability, so the complete network should be simulated and checked against the manufacturer guidance.
Recomendado
Low-Power Embedded Control
MCP6004-I/SL is suitable for embedded systems that need local analog amplification close to a microcontroller or mixed-signal processor. The typical 100 µA quiescent current complements low-power embedded-control designs, and the 1.8 V minimum supply supports low-energy systems. Four channels can serve sensor inputs, analog control outputs, and buffered feedback paths within one package. Rail-to-rail input and output operation is useful when the system does not permit conventional headroom for bipolar amplifier inputs or outputs. Designers should still include protection against transients, verify ADC input ranges, and avoid excessive capacitive loading at the amplifier output. The 1 MHz bandwidth is adequate for many control and monitoring loops but should be compared with the loop bandwidth.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MCP6004-I/SL — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MCP6004-E/SL | MCP6004T-I/SL | MCP6004-E/SLVAO | MCP607-I/SN | LMV324IDT |
|---|---|---|---|---|---|---|
| Package | SOIC-14 (SL) | SOIC-14 (SL) | SOIC-14 (SL) | SOIC-14 (SL) | SOIC-14 (SN) | SOIC-14 (DT) |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Texas Instruments |
| Amplifier Configuration | Quad | Quad | Quad | Quad | Quad | Quad |
Principais diferenciais
- Higher bandwidth than the MCP607-I/SN candidate (vs MCP607-I/SN)
- Four rail-to-rail channels in one SOIC package (vs LMV324IDT)
- Specified industrial temperature coverage (vs MCP6004-E/SL)
Notas de projeto
Place the amplifier input, feedback, and decoupling components close to their associated pins. The four channels share common supply pins, so adequate high-frequency bypass capacitance and short ground-return paths help prevent supply noise from coupling into multiple channels simultaneously. Route sensitive input traces away from switching nodes and power-stage outputs, and use a continuous ground plane to reduce return-path discontinuities.
Do not assume that rail-to-rail operation eliminates output-swing or input-range restrictions under every load condition. The actual signal must remain within the datasheet input common-mode range and output voltage limits, including margin for load current, temperature, and process variation. Also verify stable operation with the selected feedback network, source impedance, and capacitive load before releasing the PCB design.
The typical 1 MHz gain-bandwidth product limits usable closed-loop bandwidth and influences the maximum practical noise gain at a required signal frequency. Calculate the closed-loop bandwidth for each channel and add margin for filter roll-off and component tolerances. When driving an ADC, buffer the amplifier output with isolation resistance or an additional buffer if the sampling network introduces excessive capacitive loading.
Informações de conformidade
Current material-compliance declarations and exact automotive qualification status were not included in the manufacturer product summary. Obtain declarations for MCP6004-I/SL before use in regulated production.