MCP6021-I/ST - 10MHz RRIO Op Amp | Microchip Technology
N.º da peça: MCP6021-I/ST ✓ AtivoMCP6021-I/ST Visão geral
An operational amplifier, commonly called an op amp, is a voltage-feedback amplifier used to amplify, buffer, filter, compare, and control analog signals. Within the broader semiconductor hierarchy, the MCP6021-I/ST belongs to the operational-amplifier class of amplifier ICs. Its low-power design and moderate bandwidth provide a practical balance between signal responsiveness, low bias current, and compact implementation.
The principal performance attributes include a 10 MHz gain-bandwidth product, rail-to-rail input and output capability, an input bias current specified at 1 pA, and an operating current of 1.0 mA. The low input bias current is particularly useful with high-impedance sensors because it limits the error caused by bias current flowing through the source impedance. The low offset voltage supports accurate amplification around the input common-mode voltage.
In voltage-feedback operation, closed-loop bandwidth depends on the selected noise gain. At a noise gain of 1, the 10 MHz gain-bandwidth product supports substantially wider signal bandwidth than at higher closed-loop gains. Rail-to-rail input capability broadens the usable common-mode range, while rail-to-rail output operation helps the amplifier approach its supply rails under suitable output-load conditions. Designers should still evaluate output drive, load, stability, and operating conditions from the manufacturer datasheet.
Typical applications include low-power sensor conditioning, battery-powered instrumentation, audio and communication interfaces, analog signal buffering, active filtering, and general-purpose analog control. Its 1.0 mA operating current is advantageous in portable systems, while the 8-pin TSSOP package supports compact, surface-mount PCB layouts.
For reliable circuit implementation, keep input and feedback paths short, place compensation and decoupling components close to the device pins, and verify the selected gain against the datasheet stability and bandwidth information. Decoupling capacitance and voltage-headroom requirements must follow the manufacturer guidance rather than being inferred from the package alone.
This page combines manufacturer specifications, package information, sourcing data, replacement analysis, comparison tables, and practical application guidance. It also identifies where a same-footprint substitution requires validation of offset, bandwidth, operating current, temperature grade, and electrical limits before production use.
Alternativas drop-in para MCP6021-I/ST — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com MCP6021-I/ST (mesmo formato e footprint) — diferindo em Amplifier Type, Package, Typical Operating Current.
MCP6021-E/ST
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MCP6022-I/ST
✅ Drop-In ⚠️ Especificações não verificadasConsulte o preço
Ver ficha técnica →MCP6023-I/ST
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MCP6024-I/ST
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MCP6022-E/ST
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MCP6023-E/ST
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
MCP6021-I/ST Classificações máximas e características elétricas
| Amplifier Type | Single operational amplifier |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA |
| Typical Input Offset Voltage | Less than 0.5 mV |
| Input Bias Current | 1 pA |
| Input Common-Mode Range | Rail-to-rail |
| Output Swing | Rail-to-rail |
| Number of Circuits | 1 circuit |
| Encapsulamento | 8-pin TSSOP |
| Package Width | 4.40 mm |
| Tipo de montagem | Surface mount |
| Status RoHS | RoHS |
Guia de Configuração de Pinos do MCP6021-I/ST 4.40 mm
Configuração de pinos para MCP6021-I/ST (pacote 4.40 mm). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.
Nenhum dado detalhado de pinagem disponível para MCP6021-I/ST.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
MCP6021-I/ST é adequado para 6 aplicaçãos: Battery-Powered Sensor Conditioning, Portable Audio Signal Interface, Active Analog Filtering, Industrial Instrumentation Buffer, Communication Interface Buffer, Precision DC Signal Amplification.
Battery-Powered Sensor Conditioning
The MCP6021-I/ST fits low-power sensor front ends because its 1.0 mA typical operating current limits system overhead while the 1 pA input bias current reduces the error produced across a high-impedance sensor. Its rail-to-rail input also helps process signals near the supply range in compact, low-energy equipment. Use it as a voltage follower or noninverting amplifier ahead of an ADC, checking the sensor impedance, leakage, noise, and the amplifier's offset and stability requirements.
Recomendado
Portable Audio Signal Interface
MCP6021-I/ST can condition low-level audio or communications signals in portable equipment while consuming only 1.0 mA typical operating current. Rail-to-rail input and output behavior provides useful signal-headroom flexibility in low-voltage systems, while the 10 MHz gain-bandwidth product supports moderate-bandwidth amplification. The device can buffer a microphone or line-level stage, although output loading, distortion, noise, and stability should be checked at the selected closed-loop gain.
Recomendado
Active Analog Filtering
The 10 MHz gain-bandwidth product makes MCP6021-I/ST suitable for active filters handling signals below the closed-loop bandwidth permitted by the selected topology. Its 1.0 mA operating current is useful in portable measurement systems, and the low input bias current reduces loading of high-impedance filter stages. Component tolerances, gain-bandwidth behavior, output drive, and noise must be evaluated together, especially near the amplifier's upper bandwidth where stability can become more sensitive.
Recomendado
Industrial Instrumentation Buffer
MCP6021-I/ST is appropriate for buffering sensor and measurement signals where compact implementation and low current are valuable. Its listed 1 pA input bias current minimizes interaction with high-impedance sources, while rail-to-rail input operation accommodates signals across much of the available common-mode range. The 8-pin TSSOP package supports compact industrial control boards, but designers should verify the exact I/ST temperature limits, supply range, ESD requirements, and long-term calibration behavior.
Recomendado
Communication Interface Buffer
MCP6021-I/ST can provide low-power buffering for communication front ends operating from a limited supply budget. The 10 MHz gain-bandwidth product covers many moderate-speed signal-conditioning paths, and the 1.0 mA operating current is valuable in battery-backed links. Use the amplifier where its input capacitance, output drive, noise, and common-mode limits are acceptable. High-speed or long-trace interfaces may require separate analysis for bandwidth, impedance, ringing, and EMC behavior.
Recomendado
Precision DC Signal Amplification
MCP6021-I/ST is suitable for low-level DC amplification because the manufacturer identifies a typical input offset voltage below 0.5 mV and a 1 pA input bias current. These characteristics reduce errors when processing outputs from strain gauges, temperature sensors, and other high-impedance transducers. Its 10 MHz bandwidth leaves ample speed for many precision DC paths, although accuracy also depends on resistor matching, input-referred noise, temperature drift, bias-current return path, and power-supply rejection.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para MCP6021-I/ST — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | MCP6021-E/ST | MCP6022-I/ST | MCP6023-I/ST | MCP6024-I/ST | MCP6022-E/ST |
|---|---|---|---|---|---|---|
| Package | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP | 8-TSSOP |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Amplifier Configuration | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier | Single operational amplifier |
| Gain-Bandwidth Product | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 10 MHz | 10 MHz |
| Typical Operating Current | 1.0 mA | 1.0 mA | 1.0 mA | 1.0 mA | 1.0 mA | 1.0 mA |
| Input Common-Mode Range | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
| Output Swing | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail | Rail-to-rail |
Principais diferenciais
- Lower-offset MCP6021 family grade (vs MCP6024-I/ST)
- Low operating current with substantial bandwidth (vs MCP6022-I/ST)
- Compact pin-compatible family options (vs MCP6021-E/ST)
Notas de projeto
Route the op-amp output directly to the feedback network and keep the inverting input path short to minimize parasitic feedback and oscillation risk. Place any decoupling capacitor immediately across the supply pins and connect its ground return directly to the device ground pin. Avoid routing sensitive high-impedance input nets beneath or beside switching-node and digital return paths, particularly when the MCP6021-I/ST is used with a 1 pA-class bias-current input.
Verify closed-loop stability at every intended gain, capacitive load, and output-current condition. The 10 MHz gain-bandwidth product is not the usable closed-loop bandwidth for every circuit; at higher noise gain, bandwidth and phase margin change. Add an isolation resistor between the output and difficult capacitive loads if the manufacturer stability guidance indicates it is required. Validate the final layout with oscilloscope measurements at the intended signal frequencies.
Do not assume that rail-to-rail input and output operation eliminates all supply-rail limitations. The input common-mode range, output swing, output drive, and stable operating region still depend on the exact supply voltage and load. Confirm the I/ST temperature grade and worst-case electrical limits in the manufacturer documentation. For high-impedance sources, provide a suitable bias-current return path and account for PCB contamination leakage.
Informações de conformidade
The verified LCSC listing identifies the MCP6021-I/ST as RoHS. No specific AEC-Q100 qualification is indicated for this non-automotive orderable code; additional environmental and material-compliance details require confirmation from the manufacturer.