Microchip Technology

MCP6022-I/SN - 10MHz Dual RRIO Op Amp | Microchip

N.º da peça: MCP6022-I/SN ✓ Ativo
<0.5 mV Vdss 1.0 mA Id 8-pin SOIC Package
MOQ: 1 |

MCP6022-I/SN Visão geral

The Microchip Technology MCP6022-I/SN is a dual operational amplifier with rail-to-rail input and output operation, a 10 MHz gain-bandwidth product, a typical operating current of 1.0 mA per amplifier, and an input offset voltage below 0.5 mV. The device is packaged in an 8-pin SOIC and is intended for general-purpose low-voltage signal conditioning.

An operational amplifier is a high-gain, feedback-controlled amplifier used to amplify, buffer, filter, or compare small analog signals. The MCP6022 combines two amplifier channels in one package and belongs to the broader hierarchy of analog signal-chain ICs, where precision op amps sit between sensors, converters, and actuator drivers. Rail-to-rail input and output capability allows useful signal swing close to the supply rails in low-voltage systems.

The MCP6022 family provides 8.7 nV/√Hz input-noise performance and low distortion of 0.00053% THD+N, according to the manufacturer documentation. Its 10 MHz bandwidth makes it suitable for signal paths that require more speed than low-frequency precision amplifiers while retaining the low power consumption of 1.0 mA typical operating current. Two independent channels can implement paired filters, amplifiers, buffers, or comparator functions.

Advanced CMOS construction supports the family’s combination of low power, wide bandwidth, and rail-to-rail operation. The low input offset helps reduce signal-generation error in precision feedback networks, while the 8.7 nV/√Hz noise density favors low-noise signal conditioning. These characteristics balance bandwidth and noise without introducing the higher power consumption commonly associated with much faster precision amplifiers.

Typical uses include low-level sensor conditioning, current-sense amplifier building blocks, active filters, audio preamplification, ADC or DAC driver stages, and general-purpose buffering. The dual configuration is especially useful when a board needs two related analog channels while keeping the component count and footprint small. The 8-pin SOIC package also remains practical for conventional through-hole assembly and prototype boards.

Designers should verify input and output common-mode limits, capacitive-load stability, supply-voltage range, and noise performance at the intended operating frequency before finalizing a board. Decoupling capacitors should be placed close to the supply pins, while feedback resistors should be kept compact to minimize parasitic capacitance. Stable feedback ratios and suitable output isolation are important when driving capacitive loads.

Alternativas drop-in para MCP6022-I/SN — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com MCP6022-I/SN (mesmo formato e footprint) — diferindo em Package, Output Swing, Input Common-Mode Range, Input Offset Voltage, Number of Channels.

Microchip Technology
Package: 8-pin SOIC (SN)
Output Swing: Rail-to-Rail
Number of Channels: 2 (dual)
Microchip Technology
Package: SOIC-8, 4.9 mm x 3.9 mm
Output Swing: Rail-to-rail
Input Common-Mode Range: Rail-to-rail

MCP6022-E/SN

✅ Drop-In
Microchip Technology
📦 8-pin SOIC
2 channels · 10 MHz · 1.0 mA · Less than 0.5 mV · 2.5 V to 5.5 V · Rail-to-rail · Rail-to-rail · 8.7 nV/√Hz

Consulte o preço

Ver ficha técnica →

MCP6022T-I/SNVAO

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz dual rail-to-rail family and 8-pin SOIC footprint; suffix-specific qualification and ordering attributes differ

📋 Alternativa de referência (fora do catálogo)

MCP6022T-E/SNVAO

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz dual rail-to-rail family and 8-pin SOIC footprint; -E grade and VAO ordering attributes replace the -I ordering attributes

📋 Alternativa de referência (fora do catálogo)

MCP6022T-I/SN

✅ Drop-In
📦 8-pin SOIC
Same 10 MHz dual rail-to-rail family and 8-pin SOIC footprint; T ordering code changes the reel-related packing configuration

📋 Alternativa de referência (fora do catálogo)

MCP6002T-I/SNVAO

✅ Drop-In
📦 8-pin SOIC
Same 8-SOIC dual general-purpose amplifier format; different MCP6002 series with series-specific offset, noise, supply, and qualification limits

📋 Alternativa de referência (fora do catálogo)

MCP6022-I/SN Classificações máximas e características elétricas

Amplifier Type Dual general-purpose operational amplifier
Number of Channels 2 channels
Gain-Bandwidth Product 10 MHz
Typical Operating Current 1.0 mA
Input Offset Voltage <0.5 mV
Input Noise Density 8.7 nV/√Hz
Total Harmonic Distortion Plus Noise 0.00053% THD+N
Input Common-Mode Range Rail-to-rail input
Output Swing Rail-to-rail output
Process Technology Advanced CMOS
Encapsulamento 8-pin SOIC
Tipo de montagem Surface mount

Configuração de pinos do MCP6022-I/SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pino 1 OUTA — Amplifier A output
Pino 2 INA- — Inverting input for amplifier A
Pino 3 INA+ — Noninverting input for amplifier A
Pino 4 V- — Negative supply connection
Pino 5 INB+ — Noninverting input for amplifier B
Pino 6 INB- — Inverting input for amplifier B
Pino 7 OUTB — Amplifier B output
Pino 8 V+ — Positive supply connection

Aplicações típicas

MCP6022-I/SN é adequado para 6 aplicaçãos: Low-Level Sensor Signal Conditioning, Active Audio Preamplification, ADC Signal Conditioning and Driver, Precision Active Filtering, Battery-Powered Portable Instruments, Industrial Control and Instrumentation.

🧩

Low-Level Sensor Signal Conditioning

The MCP6022-I/SN is well suited to conditioning weak sensor signals because its input noise density is 8.7 nV/√Hz and input offset voltage is below 0.5 mV. Rail-to-rail input operation allows the amplifier to accept signals near the supply limits, while the 10 MHz gain-bandwidth product provides useful bandwidth for sensor dynamics and filtering. A typical implementation places the sensor at the noninverting input and uses a feedback network in the inverting input. The designer should account for sensor source impedance, resistor-generated thermal noise, common-mode rejection, and the amplifier’s input bias current.

🎧

Active Audio Preamplification

The MCP6022-I/SN can amplify small audio-frequency signals in portable and consumer equipment while maintaining a 1.0 mA typical operating current. Its rail-to-rail input and output behavior supports single-supply operation, and the documented 0.00053% THD+N provides a useful low-distortion starting point. Each channel can form a non-inverting preamplifier with feedback components that establish gain and bandwidth. Input and output coupling capacitors should be selected from the actual signal-bias and frequency-response requirements.

📺

ADC Signal Conditioning and Driver

The MCP6022-I/SN provides a practical 10 MHz signal-conditioning stage ahead of an ADC. Rail-to-rail input capability handles signals that occupy much of the available supply range, while the low output impedance helps isolate the ADC sampling network from the preceding source. A common design uses one channel as a gain stage and the other for filtering or offset adjustment. Confirm the ADC input range, acquisition time, input capacitance, and the op amp’s capacitive-load behavior before closing the signal chain.

🔧

Precision Active Filtering

The 10 MHz gain-bandwidth product of the MCP6022-I/SN supports active low-pass, high-pass, and band-pass filters formed with external resistors and capacitors. Input offset voltage below 0.5 mV is important when a filter operates close to the signal floor, while the 8.7 nV/√Hz noise density contributes to the amplifier noise budget. Each amplifier channel can implement one filter section, enabling a two-stage filter or a signal-conditioning path with another function. Component tolerances and the operating frequency should be evaluated together because the amplifier is not intended to eliminate passive-component error.

📱

Battery-Powered Portable Instruments

A 1.0 mA typical operating current makes the MCP6022-I/SN suitable for battery-powered instruments where two analog channels must operate without excessive supply demand. The device’s rail-to-rail input and output characteristics reduce signal-range restrictions in low-voltage systems, and the dual 8-pin SOIC package limits board area. One channel may provide gain while the other buffers a reference or monitor signal. Battery life analysis should include supply current, load-dependent consumption, regulator quiescent current, and the actual signal duty cycle.

🏭

Industrial Control and Instrumentation

The MCP6022-I/SN can serve as a general-purpose analog building block in industrial control and instrumentation circuits because it combines two channels, 10 MHz bandwidth, low offset, and rail-to-rail operation. The -I ordering grade is relevant when the required ambient-temperature range exceeds that of the -E alternative. Typical uses include conditioning sensor inputs, buffering control outputs, and amplifying error signals around a comparator. The final design should account for industrial noise, grounding, supply regulation, temperature limits, and any required AEC-Q100 or other qualification.

Resumo dos produtos recomendados

MCP6021 Single-channel member of the same rail-to-rail amplifier family Usado em: Low-Level Sensor Signal Conditioning, Active Audio Preamplification, Precision Active Filtering, Battery-Powered Portable Instruments MCP6023 Related dual amplifier family option Usado em: Low-Level Sensor Signal Conditioning, Active Audio Preamplification, ADC Signal Conditioning and Driver, Precision Active Filtering, Industrial Control and Instrumentation MCP6024 Related dual amplifier family option Usado em: Low-Level Sensor Signal Conditioning, Active Audio Preamplification, ADC Signal Conditioning and Driver, Precision Active Filtering, Industrial Control and Instrumentation PCM3060PWR Texas Instruments Usado em: ADC Signal Conditioning and Driver, Battery-Powered Portable Instruments PCM3010DBR Texas Instruments Usado em: Battery-Powered Portable Instruments ADS1262IPW Texas Instruments Usado em: Industrial Control and Instrumentation
What are the key specifications of MCP6022-I/SN that engineers should know?
The MCP6022-I/SN is a dual, 10 MHz, rail-to-rail input-and-output CMOS operational amplifier with 1.0 mA typical operating current, input offset voltage below 0.5 mV, and input noise density of 8.7 nV/√Hz. According to the Microchip manufacturer datasheet, the device also offers low distortion of 0.00053% THD+N. It is supplied in an 8-pin SOIC package, making it suitable for low-voltage filtering, buffering, sensor conditioning, and general analog signal-processing circuits.
What is the operating voltage of MCP6022-I/SN?
The exact supply-voltage range is not stated in the retrieved manufacturer product summary, so consult the MCP6022 manufacturer datasheet before selecting the supply rails. The device is identified as a rail-to-rail input and output operational amplifier with a 10 MHz gain-bandwidth product and 1.0 mA typical operating current. The rail-to-rail designation describes input common-mode and output-swing behavior; it does not mean any supply voltage can be used.
What is the MCP6022-I/SN pinout?
The MCP6022-I/SN uses an 8-pin SOIC with two complete amplifier channels. Pins 1 and 7 are OUTA and OUTB; pins 2 and 6 are INA− and INB−; pins 3 and 5 are INA+ and INB+; pin 4 is V−; and pin 8 is V+. According to the Microchip manufacturer pin-description table, the exposed package has no separate exposed thermal pad. Use the datasheet pin table when assigning PCB tracks.
Where can I download the MCP6022-I/SN datasheet PDF?
The official MCP6022 datasheet and product resources are available from the Microchip Technology MCP6022 product page at https://www.microchip.com/en-us/product/MCP6022. The MCP6022-I/SN is the industrial suffix of the MCP6022 dual-amplifier family. The manufacturer documentation provides the authoritative electrical characteristics, pin descriptions, package drawings, and typical application information needed for design review.
Is MCP6022-I/SN suitable for low-noise sensor conditioning?
The MCP6022-I/SN is suitable for many low-noise sensor-conditioning stages because its input noise density is 8.7 nV/√Hz, input offset voltage is below 0.5 mV, and rail-to-rail input operation supports signals near the supply limits. According to the Microchip manufacturer documentation, the device delivers 10 MHz bandwidth at 1.0 mA typical operating current. Source resistance, sensor noise, gain, and the required signal bandwidth must be evaluated together.
Can MCP6022-I/SN drive an ADC input?
The MCP6022-I/SN can provide a low-impedance drive stage for many ADC inputs because it has 10 MHz gain-bandwidth product, rail-to-rail output operation, and 8.7 nV/√Hz input noise density. According to the Microchip manufacturer datasheet, the device can also buffer signals with low distortion of 0.00053% THD+N. Check the ADC acquisition-time requirements and confirm the op-amp stability with the ADC’s sampling-capacitance network.
What is the difference between MCP6022-I/SN and MCP6002T-I/SNVAO?
Both devices appear in a direct comparison as 8-SOIC general-purpose amplifier options, but they belong to different Microchip series and should not be treated as automatically interchangeable. The MCP6022-I/SN has a documented 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and input offset voltage below 0.5 mV. The MCP6002T-I/SNVAO must be checked separately for offset, noise, supply range, stability, and qualification before substitution.
When should I choose MCP6022-I/SN over another dual op amp?
Choose MCP6022-I/SN when the design needs two channels, rail-to-rail input and output operation, a 10 MHz gain-bandwidth product, and approximately 1.0 mA typical operating current per amplifier. Its documented offset voltage below 0.5 mV and 8.7 nV/√Hz noise density make it attractive for sensor, filter, and ADC-driver circuits. Select another family only when a required limit, such as supply range, capacitive-load drive, offset, or automotive qualification, is not met.
Is MCP6022-I/SN suitable for battery-powered equipment?
The MCP6022-I/SN is a strong candidate for battery-powered equipment because its 1.0 mA typical operating current is low for a dual, 10 MHz operational amplifier. The rail-to-rail input and output architecture also supports systems that require signal operation close to low supply voltages. According to the Microchip manufacturer product summary, both amplifier channels are integrated into one 8-pin SOIC, reducing component count while maintaining low power consumption.
Where can I buy MCP6022-I/SN online?
Use the Request a Quote form on this page to request MCP6022-I/SN availability, lot traceability, and a current quotation. The exact MPN is also listed by authorized distribution channels, but inventory and commercial terms can change without notice. For production procurement, specify the complete MCP6022-I/SN ordering code, required quantity, date code policy, and acceptable delivery schedule with the request.
What is the price of MCP6022-I/SN?
The current commercial price for MCP6022-I/SN should be obtained through the Request a Quote form on this page. The form can account for quantity, delivery schedule, traceability requirements, and current market conditions more accurately than a static listing. Confirm that the quotation is for the complete MCP6022-I/SN ordering code and an 8-pin SOIC package rather than a related amplifier series.
What is the lead time for MCP6022-I/SN?
The current lead time for MCP6022-I/SN should be requested through the Request a Quote form on this page. Lead time can depend on order quantity, scheduled delivery date, and required traceability. Include the target quantity and production schedule in the request so the supplier can confirm the appropriate manufacturing and allocation plan for the exact 8-pin SOIC device.
Is MCP6022-I/SN in stock?
Use the Request a Quote form on this page to check current MCP6022-I/SN stock and delivery availability. The manufacturer product page identifies the MCP6022 family, while individual channel inventory can vary by quantity and fulfillment schedule. A stock confirmation should cover the complete MCP6022-I/SN MPN, 8-pin SOIC package, quantity, and required ship date.
What can replace MCP6022-I/SN on the same 8-pin SOIC footprint?
MCP6022-E/SN is a same-family candidate because it retains the MCP6022 dual rail-to-rail 10 MHz amplifier configuration in the 8-pin SOIC package. MCP6022T-E/SNVAO and MCP6022T-I/SNVAO also appear in cross-reference results as MCP6022-family alternatives. Before replacing the -I grade, verify the temperature-grade limits, offset voltage, input bias current, noise, supply range, and AEC-Q100 status in the manufacturer datasheets.
What is the best Microchip equivalent for MCP6022-I/SN?
The closest same-family starting point is MCP6022-E/SN because it remains a dual, 8-pin SOIC, 10 MHz rail-to-rail amplifier while changing the temperature-grade suffix from -I to -E. The cross-reference results also identify MCP6022T-E/SNVAO and MCP6022T-I/SNVAO. Those alternatives are not automatically drop-in replacements until their suffix-specific temperature, qualification, and ordering requirements are checked against the original design.

Dados de referência de engenharia para MCP6022-I/SN — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose MCP6022-I/SN when a design requires two rail-to-rail input/output channels, a 10 MHz gain-bandwidth product, 1.0 mA typical operating current, and low offset and noise in an 8-pin SOIC. MCP6022-E/SN is the closest same-family option when the -E temperature grade is acceptable. MCP6022T-I/SNVAO or MCP6022T-E/SNVAO may fit when their specific ordering and qualification attributes are required. MCP6022T-I/SN preserves the family’s electrical configuration but changes the T packing ordering code. MCP6002T-I/SNVAO should be considered only after a direct review confirms its offset, noise, bias current, supply range, stability, and qualification requirements. For all alternatives, verify the complete manufacturer datasheet rather than relying only on shared packaging and amplifier count.

Comparação com alternativas

Parâmetro Este produto MCP6022-E/SN MCP6022T-I/SNVAO MCP6022T-E/SNVAO MCP6022T-I/SN MCP6002T-I/SNVAO
Package 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC 8-pin SOIC
Brand Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology Microchip Technology
Number of Amplifier Channels 2 channels 2 channels 2 channels 2 channels 2 channels 2 channels
Temperature-Grade Suffix -I -E -I -E -I -I
Special Ordering Attributes SN suffix SN suffix T and VAO suffixes T, E, and VAO suffixes T suffix T and VAO suffixes

Principais diferenciais

  • Combines two 10 MHz amplifier channels with low operating current (vs MCP6002T-I/SNVAO)
  • Maintains the same documented core performance across the -I MCP6022 ordering options (vs MCP6022T-I/SN)
  • Offers the -I temperature-grade ordering option for wider industrial design intent (vs MCP6022-E/SN)

Notas de projeto

Place the supply bypass capacitor directly between pins 8 and 4, with a short return path to the amplifier ground reference. Keep input and feedback components close to pins 1–3 and 5–7 to minimize parasitic capacitance and susceptibility to injected noise. The two amplifier channels are not internally isolated, so their ground and supply references must be handled consistently when the channels process signals from different circuit domains.

Do not assume that the suffix-level alternatives have identical temperature or qualification limits. MCP6022-E/SN changes the grade from -I to -E, while VAO and T suffixes introduce additional ordering attributes that must be interpreted from the manufacturer ordering guide. Verify input common-mode range, output swing, supply limits, load stability, input bias current, offset limits, and noise before approving a substitution.

The 10 MHz gain-bandwidth product does not guarantee closed-loop bandwidth of 10 MHz. For a non-inverting gain of 10, the nominal bandwidth is approximately 1 MHz before considering noise gain and closed-loop response. Avoid excessive closed-loop gain when high-frequency signals are present, and evaluate the chosen feedback resistors against noise, bias-current error, and parasitic capacitance.

The stated 1.0 mA operating current should be checked against the manufacturer’s full test conditions and load profile. Rail-to-rail output stages can require additional current as the output approaches a supply rail, while capacitive loads can increase dynamic demand. Leave the circuit operating within the specified common-mode and output-swing limits instead of assuming full rail-to-rail behavior under every load condition.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The retrieved manufacturer and distributor summaries do not state a definitive compliance declaration for this exact MPN. Consult the current Microchip product declaration, material declaration, and orderable-part documentation before making a compliance claim.

Dados verificados em: 2026-11-20 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

mcp6022-i/sn datasheet mcp6022 datasheet mcp6022 pinout mcp6022 op amp mcp6022 vs mcp6002 mcp6022 price mcp6022 pdf mcp6022 equivalent Microchip MCP6022-I/SN MCP6022-I/SN replacement MCP6022-I/SN 10MHz op amp MCP6022-I/SN SOIC-8 pinout

Componentes & termos relacionados

Microchip Technology MCP6022-I/SN MCP6022 MCP6022-E/SN MCP6022T-I/SN MCP6022T-I/SNVAO MCP6022T-E/SNVAO MCP6002T-I/SNVAO operational amplifier dual op amp rail-to-rail input rail-to-rail output CMOS gain-bandwidth product input offset voltage input noise density THD+N 8-pin SOIC SOIC package surface-mount package analog signal conditioning active filter ADC driver industrial control battery-powered equipment
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ