MCP6022-I/SN - 10MHz Dual RRIO Op Amp | Microchip
MPN: MCP6022-I/SN ✓ فعالMCP6022-I/SN جائزہ
An operational amplifier is a high-gain, feedback-controlled amplifier used to amplify, buffer, filter, or compare small analog signals. The MCP6022 combines two amplifier channels in one package and belongs to the broader hierarchy of analog signal-chain ICs, where precision op amps sit between sensors, converters, and actuator drivers. Rail-to-rail input and output capability allows useful signal swing close to the supply rails in low-voltage systems.
The MCP6022 family provides 8.7 nV/√Hz input-noise performance and low distortion of 0.00053% THD+N, according to the manufacturer documentation. Its 10 MHz bandwidth makes it suitable for signal paths that require more speed than low-frequency precision amplifiers while retaining the low power consumption of 1.0 mA typical operating current. Two independent channels can implement paired filters, amplifiers, buffers, or comparator functions.
Advanced CMOS construction supports the family’s combination of low power, wide bandwidth, and rail-to-rail operation. The low input offset helps reduce signal-generation error in precision feedback networks, while the 8.7 nV/√Hz noise density favors low-noise signal conditioning. These characteristics balance bandwidth and noise without introducing the higher power consumption commonly associated with much faster precision amplifiers.
Typical uses include low-level sensor conditioning, current-sense amplifier building blocks, active filters, audio preamplification, ADC or DAC driver stages, and general-purpose buffering. The dual configuration is especially useful when a board needs two related analog channels while keeping the component count and footprint small. The 8-pin SOIC package also remains practical for conventional through-hole assembly and prototype boards.
Designers should verify input and output common-mode limits, capacitive-load stability, supply-voltage range, and noise performance at the intended operating frequency before finalizing a board. Decoupling capacitors should be placed close to the supply pins, while feedback resistors should be kept compact to minimize parasitic capacitance. Stable feedback ratios and suitable output isolation are important when driving capacitive loads.
کے لیے ڈراپ اِن متبادل MCP6022-I/SN — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں MCP6022-I/SN (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Package, Output Swing, Input Common-Mode Range, Input Offset Voltage, Number of Channels.
MCP6022-E/SN
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →MCP6022T-I/SNVAO
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCP6022T-E/SNVAO
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCP6022T-I/SN
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCP6002T-I/SNVAO
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MCP6022-I/SN زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Dual general-purpose operational amplifier |
| Number of Channels | 2 channels |
| Gain-Bandwidth Product | 10 MHz |
| Typical Operating Current | 1.0 mA |
| Input Offset Voltage | <0.5 mV |
| Input Noise Density | 8.7 nV/√Hz |
| Total Harmonic Distortion Plus Noise | 0.00053% THD+N |
| Input Common-Mode Range | Rail-to-rail input |
| Output Swing | Rail-to-rail output |
| Process Technology | Advanced CMOS |
| پیکیج | 8-pin SOIC |
| ماؤنٹنگ ٹائپ | Surface mount |
MCP6022-I/SN پن کنفیگریشن
| پن 1 | OUTA — Amplifier A output |
| پن 2 | INA- — Inverting input for amplifier A |
| پن 3 | INA+ — Noninverting input for amplifier A |
| پن 4 | V- — Negative supply connection |
| پن 5 | INB+ — Noninverting input for amplifier B |
| پن 6 | INB- — Inverting input for amplifier B |
| پن 7 | OUTB — Amplifier B output |
| پن 8 | V+ — Positive supply connection |
عام استعمالات
MCP6022-I/SN کے لیے موزوں ہے 6 ایپلیکیشنs: Low-Level Sensor Signal Conditioning, Active Audio Preamplification, ADC Signal Conditioning and Driver, Precision Active Filtering, Battery-Powered Portable Instruments, Industrial Control and Instrumentation.
Low-Level Sensor Signal Conditioning
The MCP6022-I/SN is well suited to conditioning weak sensor signals because its input noise density is 8.7 nV/√Hz and input offset voltage is below 0.5 mV. Rail-to-rail input operation allows the amplifier to accept signals near the supply limits, while the 10 MHz gain-bandwidth product provides useful bandwidth for sensor dynamics and filtering. A typical implementation places the sensor at the noninverting input and uses a feedback network in the inverting input. The designer should account for sensor source impedance, resistor-generated thermal noise, common-mode rejection, and the amplifier’s input bias current.
تجویز کردہ
Active Audio Preamplification
The MCP6022-I/SN can amplify small audio-frequency signals in portable and consumer equipment while maintaining a 1.0 mA typical operating current. Its rail-to-rail input and output behavior supports single-supply operation, and the documented 0.00053% THD+N provides a useful low-distortion starting point. Each channel can form a non-inverting preamplifier with feedback components that establish gain and bandwidth. Input and output coupling capacitors should be selected from the actual signal-bias and frequency-response requirements.
تجویز کردہ
ADC Signal Conditioning and Driver
The MCP6022-I/SN provides a practical 10 MHz signal-conditioning stage ahead of an ADC. Rail-to-rail input capability handles signals that occupy much of the available supply range, while the low output impedance helps isolate the ADC sampling network from the preceding source. A common design uses one channel as a gain stage and the other for filtering or offset adjustment. Confirm the ADC input range, acquisition time, input capacitance, and the op amp’s capacitive-load behavior before closing the signal chain.
تجویز کردہ
Precision Active Filtering
The 10 MHz gain-bandwidth product of the MCP6022-I/SN supports active low-pass, high-pass, and band-pass filters formed with external resistors and capacitors. Input offset voltage below 0.5 mV is important when a filter operates close to the signal floor, while the 8.7 nV/√Hz noise density contributes to the amplifier noise budget. Each amplifier channel can implement one filter section, enabling a two-stage filter or a signal-conditioning path with another function. Component tolerances and the operating frequency should be evaluated together because the amplifier is not intended to eliminate passive-component error.
تجویز کردہ
Battery-Powered Portable Instruments
A 1.0 mA typical operating current makes the MCP6022-I/SN suitable for battery-powered instruments where two analog channels must operate without excessive supply demand. The device’s rail-to-rail input and output characteristics reduce signal-range restrictions in low-voltage systems, and the dual 8-pin SOIC package limits board area. One channel may provide gain while the other buffers a reference or monitor signal. Battery life analysis should include supply current, load-dependent consumption, regulator quiescent current, and the actual signal duty cycle.
تجویز کردہ
Industrial Control and Instrumentation
The MCP6022-I/SN can serve as a general-purpose analog building block in industrial control and instrumentation circuits because it combines two channels, 10 MHz bandwidth, low offset, and rail-to-rail operation. The -I ordering grade is relevant when the required ambient-temperature range exceeds that of the -E alternative. Typical uses include conditioning sensor inputs, buffering control outputs, and amplifying error signals around a comparator. The final design should account for industrial noise, grounding, supply regulation, temperature limits, and any required AEC-Q100 or other qualification.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا MCP6022-I/SN — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | MCP6022-E/SN | MCP6022T-I/SNVAO | MCP6022T-E/SNVAO | MCP6022T-I/SN | MCP6002T-I/SNVAO |
|---|---|---|---|---|---|---|
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Number of Amplifier Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Temperature-Grade Suffix | -I | -E | -I | -E | -I | -I |
| Special Ordering Attributes | SN suffix | SN suffix | T and VAO suffixes | T, E, and VAO suffixes | T suffix | T and VAO suffixes |
اہم امتیازی خصوصیات
- Combines two 10 MHz amplifier channels with low operating current (بمقابلہMCP6002T-I/SNVAO)
- Maintains the same documented core performance across the -I MCP6022 ordering options (بمقابلہMCP6022T-I/SN)
- Offers the -I temperature-grade ordering option for wider industrial design intent (بمقابلہMCP6022-E/SN)
ڈیزائن نوٹس
Place the supply bypass capacitor directly between pins 8 and 4, with a short return path to the amplifier ground reference. Keep input and feedback components close to pins 1–3 and 5–7 to minimize parasitic capacitance and susceptibility to injected noise. The two amplifier channels are not internally isolated, so their ground and supply references must be handled consistently when the channels process signals from different circuit domains.
Do not assume that the suffix-level alternatives have identical temperature or qualification limits. MCP6022-E/SN changes the grade from -I to -E, while VAO and T suffixes introduce additional ordering attributes that must be interpreted from the manufacturer ordering guide. Verify input common-mode range, output swing, supply limits, load stability, input bias current, offset limits, and noise before approving a substitution.
The 10 MHz gain-bandwidth product does not guarantee closed-loop bandwidth of 10 MHz. For a non-inverting gain of 10, the nominal bandwidth is approximately 1 MHz before considering noise gain and closed-loop response. Avoid excessive closed-loop gain when high-frequency signals are present, and evaluate the chosen feedback resistors against noise, bias-current error, and parasitic capacitance.
The stated 1.0 mA operating current should be checked against the manufacturer’s full test conditions and load profile. Rail-to-rail output stages can require additional current as the output approaches a supply rail, while capacitive loads can increase dynamic demand. Leave the circuit operating within the specified common-mode and output-swing limits instead of assuming full rail-to-rail behavior under every load condition.
تعمیل کی معلومات
The retrieved manufacturer and distributor summaries do not state a definitive compliance declaration for this exact MPN. Consult the current Microchip product declaration, material declaration, and orderable-part documentation before making a compliance claim.