Microchip Technology

MCP6033-E/SN - 1.8V 10kHz Low-Power Op Amp | Microchip

N.º da peça: MCP6033-E/SN ✓ Ativo
1.8 V Vdss 0.9 µA typical Id 8-SOIC, 3.90 mm width Package
MOQ: 1 |

MCP6033-E/SN Visão geral

The Microchip Technology MCP6033-E/SN is a single-circuit, general-purpose operational amplifier with rail-to-rail input and output, a 10 kHz gain-bandwidth product, and a typical quiescent current of 0.9 µA. It operates from a low supply voltage down to 1.8 V and supports supply voltages up to 5.5 V, all in an 8-pin SOIC package. The device also provides chip-select capability for systems that need to place an amplifier in a low-power state.

An operational amplifier, or op amp, is an analog integrated circuit that provides high open-loop gain and differential input sensing. The MCP6033 belongs to the precision-amplifier hierarchy, combining a low-power voltage regulator design with rail-to-rail signal handling. Rail-to-rail inputs let the amplifier accept signals close to either supply rail, while rail-to-rail outputs provide useful output swing at low supply voltages and light loads.

The MCP6033-E/SN combines a maximum input offset voltage of ±150 µV with a typical gain-bandwidth product of 10 kHz. Its 0.9 µA typical quiescent current is particularly useful in battery-operated instrumentation, sensor interfaces, and portable measurement systems. The device is unity-gain stable, allowing the same amplifier configuration to be used for voltage followers, non-inverting gain stages, and basic inverting signal-conditioning circuits.

The 10 kHz gain-bandwidth product identifies this part as a low-speed, low-power precision amplifier rather than a high-bandwidth signal amplifier. This makes its bandwidth appropriate for slow sensor signals, voltage references, thermocouple interfaces, and low-frequency control loops. The 0.004 V/µs slew rate supports gradual signal transitions and helps avoid excessive output movement for low-frequency applications.

Typical uses include portable sensor conditioning, low-power current measurement, precision bridge excitation, buffered references, and low-frequency industrial control. The chip-select function can reduce system power by disabling the amplifier when its signal is not required. In multiplexed or intermittently powered systems, this capability allows multiple low-power amplifier functions to coexist without keeping every circuit continuously active.

The principal design trade-off is speed versus power: the 10 kHz bandwidth and 0.9 µA quiescent current favor low-energy operation, but they do not support wideband instrumentation or fast closed-loop settling. Designers should verify input common-mode range, output swing, noise, stability, and timing against the circuit requirements before using the amplifier with rapidly changing signals.

This product page combines the manufacturer-device characteristics with practical pin, package, selection, and design guidance. It helps engineers distinguish the MCP6033-E/SN from faster members of the same amplifier family and identify where its low-power, rail-to-rail characteristics provide practical system-level benefits.

Alternativas drop-in para MCP6033-E/SN — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

MCP6033T-E/SN

✅ Drop-In
📦 8-SOIC
Temperature-grade ordering designation differs while the MCP6033 8-SOIC electrical function is retained; confirm the exact temperature range before substitution.

📋 Alternativa de referência (fora do catálogo)

MCP6033-E/SN Classificações máximas e características elétricas

Product Type Single operational amplifier
Amplifier Type General-purpose precision amplifier
Number of Circuits 1 circuit
Minimum Supply Voltage 1.8 V
Maximum Supply Voltage 5.5 V
Rail-to-Rail Input Yes
Rail-to-Rail Output Yes
Input Offset Voltage ±150 µV maximum
Corrente de repouso 0.9 µA typical
Gain-Bandwidth Product 10 kHz typical
Slew Rate 0.004 V/µs
Gain Configuration Unity-gain stable
Chip-Select Capability Yes
Encapsulamento 8-SOIC, 3.90 mm width
Tipo de montagem Surface mount
Shipping Package Tube

Configuração de pinos do MCP6033-E/SN

SOIC-8 Package Pinout Diagram SOIC-8 8-pin small outline IC, 3.9x4.9mm, P1.27mm, JEDEC MS-012. 1 8 2 7 3 6 4 5 SOIC-8
Pino 1 NC — Not connected
Pino 2 -IN — Inverting input
Pino 3 +IN — Non-inverting input
Pino 4 V- — Negative power supply
Pino 5 CS — Chip-select control input
Pino 6 OUT — Amplifier output
Pino 7 V+ — Positive power supply
Pino 8 NC — Not connected

Aplicações típicas

MCP6033-E/SN é adequado para 6 aplicaçãos: Portable Sensor Signal Conditioning, Battery-Powered Voltage Reference Buffer, Low-Frequency Bridge Measurement, Precision Thermocouple Interface, Low-Power Current Detection, Intermittently Powered Analog Front End.

📱

Portable Sensor Signal Conditioning

The MCP6033-E/SN fits portable sensor interfaces because it operates down to 1.8 V while drawing only 0.9 µA typical quiescent current. Its rail-to-rail input and output behavior accommodates sensor signals near the supply rails, and the ±150 µV maximum offset supports accurate amplification of small changes. A 10 kHz gain-bandwidth product is appropriate for temperature, pressure, and chemical sensors whose useful bandwidth is low. The principal trade-off is settling speed: use a faster amplifier when the sensor or sampling system needs faster transient response.

⚡

Battery-Powered Voltage Reference Buffer

The MCP6033-E/SN can buffer a low-current voltage reference in a battery-powered instrument while contributing only 0.9 µA typical quiescent current. Rail-to-rail input and output stages support operation from a 1.8 V supply, while the ±150 µV maximum input offset helps preserve reference accuracy. Its unity-gain stability permits a direct voltage-follower configuration, and the 10 kHz gain-bandwidth product is adequate for static or slowly varying references. Select this amplifier when reference settling speed is not the primary limitation.

🏭

Low-Frequency Bridge Measurement

The MCP6033-E/SN is useful for conditioning resistive bridge signals in compact industrial or laboratory equipment. Its rail-to-rail inputs accept small differential signals around common-mode levels near the supply rails, and the ±150 µV maximum offset limits a significant source of measurement error. At a typical quiescent current of 0.9 µA, the amplifier minimizes loading in multi-channel measurement systems. The 10 kHz gain-bandwidth product supports slow bridge scans rather than high-rate dynamic measurements, making output settling and filter design central to accurate results.

🌡️

Precision Thermocouple Interface

The MCP6033-E/SN can provide low-noise amplification for a thermocouple in a low-power temperature instrument. The 0.9 µA typical quiescent current reduces continuous power demand, and rail-to-rail input operation supports the narrow signal range produced by thermocouples. The ±150 µV maximum input offset is meaningful when the thermocouple voltage is small, although input bias current, cold-junction compensation, and error drift must also be included in the overall accuracy budget. Its 10 kHz bandwidth suits thermal measurements with relatively slow response.

🔋

Low-Power Current Detection

The MCP6033-E/SN can amplify the voltage generated across a small shunt resistor in a battery monitor or low-current power system. Operating from 1.8 V to 5.5 V allows the amplifier to work directly with low-energy rails, while its 0.9 µA typical quiescent current limits the monitoring circuit's overhead. The ±150 µV maximum offset affects the smallest detectable current, making shunt resistance and error budget important design variables. The 10 kHz bandwidth is appropriate for slow current measurements rather than high-bandwidth pulse monitoring.

🧩

Intermittently Powered Analog Front End

The MCP6033-E/SN is well suited to an intermittently powered analog front end because it combines a 0.9 µA typical quiescent current with chip-select capability. According to the Microchip Technology datasheet, CS can place the amplifier into a low-power state when its output is not needed. Rail-to-rail operation preserves useful signal range at low supply voltages, and unity-gain stability simplifies direct buffering. Design the enable sequence so that input and output states remain controlled during startup and shutdown, particularly when the amplifier drives a sampling or multiplexing network.

Resumo dos produtos recomendados

MCP6033T-E/SN Same-family MCP6033 8-SOIC option with a different temperature-grade designation Usado em: Portable Sensor Signal Conditioning, Battery-Powered Voltage Reference Buffer, Low-Frequency Bridge Measurement, Precision Thermocouple Interface, Low-Power Current Detection, Intermittently Powered Analog Front End
What is the operating voltage of MCP6033-E/SN?
The MCP6033-E/SN operates from 1.8 V to 5.5 V according to the Microchip Technology datasheet. Its rail-to-rail input and output behavior makes the amplifier suitable for low-voltage systems in which the useful signal can approach the supply rails. The wide low-voltage range supports portable instruments, low-power sensor nodes, industrial measurement circuits, and battery-powered equipment using a single 1.8 V, 2.5 V, 3.0 V, or 3.3 V supply.
What are the key specifications of MCP6033-E/SN?
The MCP6033-E/SN is a 1.8 V to 5.5 V, single-circuit operational amplifier with a 10 kHz typical gain-bandwidth product, 0.9 µA typical quiescent current, and ±150 µV maximum input offset voltage. According to the Microchip Technology datasheet, it provides rail-to-rail inputs and outputs, operates at a typical 0.004 V/µs slew rate, is unity-gain stable, and includes chip-select capability. It is packaged in an 8-SOIC.
Is MCP6033-E/SN suitable for low-power sensor applications?
Yes, the MCP6033-E/SN is suitable for low-power sensor applications because its typical quiescent current is only 0.9 µA. According to the Microchip Technology datasheet, it also accepts rail-to-rail input signals and operates down to a 1.8 V supply. It is well suited to buffering slow outputs from resistive, thermocouple, pressure, and chemical sensors where low standby consumption is more important than wideband response.
Where can I download the MCP6033-E/SN datasheet PDF?
The MCP6033-E/SN datasheet is accessible through the datasheet link on this page and through the manufacturer-device documentation linked by the product listings. The document is titled “0.9 µA, High Precision Op Amps” and covers the MCP6033 family, including electrical characteristics, the chip-select function, package information, and application guidance. Use the Microchip Technology datasheet as the controlling reference for final schematic and layout decisions.
Where can I find the MCP6033-E/SN pinout?
The MCP6033-E/SN uses an 8-SOIC pin arrangement with differential inputs, power terminals, output, chip-select control, and two not-connected positions. According to the Microchip Technology pin-description table, pin 1 is NC, pin 2 is the inverting input, pin 3 is the non-inverting input, pin 4 is V−, pin 5 is CS, pin 6 is OUT, pin 7 is V+, and pin 8 is NC. Follow the manufacturer pin-description table when assigning PCB tracks.
What is the gain-bandwidth product of MCP6033-E/SN?
The MCP6033-E/SN has a typical gain-bandwidth product of 10 kHz according to the Microchip Technology datasheet. This bandwidth supports low-frequency precision and sensing functions rather than wideband signal processing. Its unity-gain stability permits direct follower use, while the 0.004 V/µs typical slew rate produces gradual output transitions. Applications requiring substantially faster settling or higher signal bandwidth should use a higher-bandwidth amplifier.
Does MCP6033-E/SN support rail-to-rail input and output?
Yes, the MCP6033-E/SN supports rail-to-rail input and output operation. The Microchip Technology datasheet identifies the amplifier as a precision device intended for low-voltage systems where signals may lie close to the supply rails. This behavior reduces the need for signal conditioning in systems powered by 1.8 V to 5.5 V, although output swing and input common-mode limits still depend on load current and operating conditions.
What can replace MCP6033-E/SN?
The closest same-family replacement identified for MCP6033-E/SN is MCP6033T-E/SN, which retains the MCP6033 8-SOIC platform while changing the temperature-grade designation. According to the Microchip Technology family documentation, the core functional characteristics remain centered on low power, rail-to-rail operation, and precision amplification. Confirm the exact pinout, temperature grade, offset limits, and lifecycle status before approving it as a drop-in replacement.
Is MCP6033-E/SN the same as MCP6033T-E/SN?
The MCP6033-E/SN and MCP6033T-E/SN are closely related MCP6033-family devices in the same 8-SOIC format, but their temperature-grade ordering codes differ. According to the Microchip Technology family documentation, the T designation identifies a different temperature grade, while the amplifier function and low-power architecture remain comparable. Use the manufacturer ordering guide to confirm whether the T grade satisfies the required environmental range.
When should I choose MCP6033-E/SN over a faster amplifier?
Choose the MCP6033-E/SN when the circuit processes low-frequency signals and battery life matters more than bandwidth or fast settling. Its 0.9 µA typical quiescent current and 1.8 V minimum supply voltage are advantageous in portable sensor systems, while the 10 kHz gain-bandwidth product is generally adequate for slow sensor and control signals. Select a faster amplifier when the required signal bandwidth, slew rate, or output settling cannot be met.
How does MCP6033-E/SN compare with MCP6031-E/SN and MCP6032-E/SN?
The MCP6033-E/SN emphasizes extremely low power with a 0.9 µA typical quiescent current and a 10 kHz typical gain-bandwidth product. The MCP6031 and MCP6032 belong to the same low-power operating-amplifier family, but their speed and power characteristics should be compared from their individual datasheets before substitution. According to the Microchip Technology family documentation, all relevant electrical limits and temperature grades must be checked separately.
Is MCP6033-E/SN suitable for battery-operated instrumentation?
Yes, the MCP6033-E/SN is suitable for battery-operated instrumentation because it combines a 1.8 V minimum operating voltage with 0.9 µA typical quiescent current. The Microchip Technology datasheet identifies rail-to-rail inputs and outputs, making it useful for low-voltage sensor signals and buffered references. Its 10 kHz bandwidth is appropriate for slow measurements, while chip-select capability can reduce consumption during inactive measurement intervals.
Where to buy MCP6033-E/SN online?
The MCP6033-E/SN can be requested through the “Request a Quote” form on this page. The form lets you specify the required quantity, tube packaging, and delivery requirements without relying on a temporary marketplace listing. For design-in support, provide the target application, supply voltage, acceptable operating-temperature grade, and required quantity so sourcing can confirm the exact MCP6033-E/SN ordering code.
What is the lead time for MCP6033-E/SN?
Current lead time and lot availability for MCP6033-E/SN should be confirmed through the “Request a Quote” form on this page. Because supply timing can vary with manufacturer inventory and order quantity, request the required tube quantity and production schedule when seeking a quotation. Include the anticipated delivery date and any date-code requirement so the manufacturing plan can be matched to the shipment.
Is MCP6033-E/SN in stock?
Current MCP6033-E/SN availability should be checked through the “Request a Quote” form on this page rather than inferred from an individual distributor page. Submit the required quantity, package format, and target delivery date to obtain a current supply response. For production planning, state whether a partial shipment is acceptable and whether an unbroken tube or lot is required for traceability.
What is the price of MCP6033-E/SN?
Use the “Request a Quote” form on this page for the current MCP6033-E/SN price and quantity schedule. The request should specify the tube quantity, delivery location, and production timing because these factors affect the quotation. This approach also lets sourcing confirm that the quoted line uses the exact MCP6033-E/SN ordering code and the 8-SOIC package rather than a related package or temperature grade.

Dados de referência de engenharia para MCP6033-E/SN — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose MCP6033-E/SN when designing a low-voltage, low-power precision signal-conditioning circuit that operates from 1.8 V to 5.5 V. Its 0.9 µA typical quiescent current is valuable in portable and intermittently powered equipment, while rail-to-rail inputs and outputs improve usable signal range at low supply voltages. The ±150 µV maximum input offset is suitable for slow sensors and buffered references, and the chip-select pin can reduce consumption when the amplifier is inactive. MCP6033T-E/SN is the closest identified same-package option when a different temperature-grade designation is required. Confirm that the required environmental grade, output swing, bias-current contribution, noise, and settling requirements are satisfied. The MCP6033-E/SN is not the preferred choice when a circuit needs high bandwidth, fast large-signal settling, or operation above 5.5 V; select a faster or higher-voltage amplifier in those cases.

Comparação com alternativas

Parâmetro Este produto MCP6033T-E/SN
Brand Microchip Technology Microchip Technology
Package 8-SOIC 8-SOIC
Number of Circuits 1 circuit 1 circuit
Minimum Supply Voltage 1.8 V 1.8 V
Maximum Supply Voltage 5.5 V 5.5 V
Gain-Bandwidth Product 10 kHz typical 10 kHz typical
Quiescent Current 0.9 µA typical 0.9 µA typical
Input Offset Voltage ±150 µV maximum ±150 µV maximum
Input Configuration Rail-to-rail input Rail-to-rail input
Output Configuration Rail-to-rail output Rail-to-rail output
Slew Rate 0.004 V/µs 0.004 V/µs
Chip-Select Capability Yes Yes
Shipping Package Tube Tube

Principais diferenciais

  • Extremely low quiescent current for an 8-SOIC precision amplifier (vs MCP6033T-E/SN)
  • Low-voltage operation with rail-to-rail signal handling (vs MCP6033T-E/SN)
  • Precision offset performance for low-level signals (vs MCP6033T-E/SN)

Notas de projeto

Use separate supply bypass capacitors close to pins 4 and 7, with a short return path to the amplifier ground. The 0.9 µA typical quiescent current makes capacitor leakage and contamination significant at very low supply voltages; select low-leakage ceramic capacitors and verify their DC-bias derating. Add a supply-decoupling capacitor at the chip-select control pin if the manufacturer guidance calls for it, and keep digital control traces away from the inverting input to avoid coupling.

Route the non-inverting and inverting inputs as short, symmetric traces directly to pins 3 and 2, and place the gain-setting feedback components close to those inputs. Keep the output route at pin 6 separate from the input pair because even a low-frequency amplifier can couple output movement into high-impedance sensor nodes. For thermocouple or bridge measurements, use guarding, differential routing, and a clean reference plane to reduce thermoelectric and leakage-induced errors.

Do not treat the 10 kHz gain-bandwidth product as suitable for high-speed signals. Closed-loop bandwidth, slew-rate-limited settling, and output-capacitive stability must all be checked when the operating gain, signal frequency, or load differs from the unity-gain application. The 0.004 V/µs slew rate also means that large output steps require additional settling time. Confirm that the chip-select state does not create an unexpected output during startup or shutdown.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The Microchip Technology device data confirms the low-power precision-amplifier function, 1.8 V to 5.5 V operating range, 8-SOIC package, and tube shipping format. Environmental and material-compliance declarations should be confirmed against the current manufacturer product declaration before qualification.

Buscas relacionadas

mcp603 rehlko MCP6033-E/SN datasheet MCP6033-E/SN pinout MCP6033-E/SN datasheet pdf MCP6033-E/SN equivalent MCP6033-E/SN replacement MCP6033-E/SN 1.8V amplifier MCP6033-E/SN 10kHz op amp MCP6033-E/SN 8-SOIC MCP6033-E/SN price MCP6033-E/SN stock Microchip MCP6033-E/SN MCP6033-E/SN vs MCP6033T-E/SN MCP6033 low power op amp MCP6033 rail-to-rail amplifier

Componentes & termos relacionados

Microchip Technology MCP6033-E/SN MCP6033T-E/SN operational amplifier precision amplifier analog integrated circuit single-circuit amplifier rail-to-rail input rail-to-rail output low-dropout voltage regulator architecture quiescent current gain-bandwidth product input offset voltage slew rate unity-gain stable chip-select control 8-SOIC SOIC package family surface mount sensor signal conditioning portable instrumentation thermocouple interface bridge measurement battery-powered equipment
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ