MCP6033-E/SN - 1.8V 10kHz Low-Power Op Amp | Microchip
Référence : MCP6033-E/SN ✓ ActifMCP6033-E/SN Présentation
An operational amplifier, or op amp, is an analog integrated circuit that provides high open-loop gain and differential input sensing. The MCP6033 belongs to the precision-amplifier hierarchy, combining a low-power voltage regulator design with rail-to-rail signal handling. Rail-to-rail inputs let the amplifier accept signals close to either supply rail, while rail-to-rail outputs provide useful output swing at low supply voltages and light loads.
The MCP6033-E/SN combines a maximum input offset voltage of ±150 µV with a typical gain-bandwidth product of 10 kHz. Its 0.9 µA typical quiescent current is particularly useful in battery-operated instrumentation, sensor interfaces, and portable measurement systems. The device is unity-gain stable, allowing the same amplifier configuration to be used for voltage followers, non-inverting gain stages, and basic inverting signal-conditioning circuits.
The 10 kHz gain-bandwidth product identifies this part as a low-speed, low-power precision amplifier rather than a high-bandwidth signal amplifier. This makes its bandwidth appropriate for slow sensor signals, voltage references, thermocouple interfaces, and low-frequency control loops. The 0.004 V/µs slew rate supports gradual signal transitions and helps avoid excessive output movement for low-frequency applications.
Typical uses include portable sensor conditioning, low-power current measurement, precision bridge excitation, buffered references, and low-frequency industrial control. The chip-select function can reduce system power by disabling the amplifier when its signal is not required. In multiplexed or intermittently powered systems, this capability allows multiple low-power amplifier functions to coexist without keeping every circuit continuously active.
The principal design trade-off is speed versus power: the 10 kHz bandwidth and 0.9 µA quiescent current favor low-energy operation, but they do not support wideband instrumentation or fast closed-loop settling. Designers should verify input common-mode range, output swing, noise, stability, and timing against the circuit requirements before using the amplifier with rapidly changing signals.
This product page combines the manufacturer-device characteristics with practical pin, package, selection, and design guidance. It helps engineers distinguish the MCP6033-E/SN from faster members of the same amplifier family and identify where its low-power, rail-to-rail characteristics provide practical system-level benefits.
Alternatives de remplacement direct pour MCP6033-E/SN — même boîtier, compatible broche à broche. Les références à boîtier différent nécessitant une retouche du PCB sont exclues.
MCP6033T-E/SN
✅ Remplacement direct📋 Alternative de référence (hors catalogue)
MCP6033-E/SN Valeurs maximales et caractéristiques électriques
| Product Type | Single operational amplifier |
| Amplifier Type | General-purpose precision amplifier |
| Number of Circuits | 1 circuit |
| Minimum Supply Voltage | 1.8 V |
| Maximum Supply Voltage | 5.5 V |
| Rail-to-Rail Input | Yes |
| Rail-to-Rail Output | Yes |
| Input Offset Voltage | ±150 µV maximum |
| Courant de repos | 0.9 µA typical |
| Gain-Bandwidth Product | 10 kHz typical |
| Slew Rate | 0.004 V/µs |
| Gain Configuration | Unity-gain stable |
| Chip-Select Capability | Yes |
| Boîtier | 8-SOIC, 3.90 mm width |
| Type de montage | Surface mount |
| Shipping Package | Tube |
Configuration des broches de MCP6033-E/SN
| Broche 1 | NC — Not connected |
| Broche 2 | -IN — Inverting input |
| Broche 3 | +IN — Non-inverting input |
| Broche 4 | V- — Negative power supply |
| Broche 5 | CS — Chip-select control input |
| Broche 6 | OUT — Amplifier output |
| Broche 7 | V+ — Positive power supply |
| Broche 8 | NC — Not connected |
Applications typiques
MCP6033-E/SN convient pour 6 applications: Portable Sensor Signal Conditioning, Battery-Powered Voltage Reference Buffer, Low-Frequency Bridge Measurement, Precision Thermocouple Interface, Low-Power Current Detection, Intermittently Powered Analog Front End.
Portable Sensor Signal Conditioning
The MCP6033-E/SN fits portable sensor interfaces because it operates down to 1.8 V while drawing only 0.9 µA typical quiescent current. Its rail-to-rail input and output behavior accommodates sensor signals near the supply rails, and the ±150 µV maximum offset supports accurate amplification of small changes. A 10 kHz gain-bandwidth product is appropriate for temperature, pressure, and chemical sensors whose useful bandwidth is low. The principal trade-off is settling speed: use a faster amplifier when the sensor or sampling system needs faster transient response.
Recommandé
Battery-Powered Voltage Reference Buffer
The MCP6033-E/SN can buffer a low-current voltage reference in a battery-powered instrument while contributing only 0.9 µA typical quiescent current. Rail-to-rail input and output stages support operation from a 1.8 V supply, while the ±150 µV maximum input offset helps preserve reference accuracy. Its unity-gain stability permits a direct voltage-follower configuration, and the 10 kHz gain-bandwidth product is adequate for static or slowly varying references. Select this amplifier when reference settling speed is not the primary limitation.
Recommandé
Low-Frequency Bridge Measurement
The MCP6033-E/SN is useful for conditioning resistive bridge signals in compact industrial or laboratory equipment. Its rail-to-rail inputs accept small differential signals around common-mode levels near the supply rails, and the ±150 µV maximum offset limits a significant source of measurement error. At a typical quiescent current of 0.9 µA, the amplifier minimizes loading in multi-channel measurement systems. The 10 kHz gain-bandwidth product supports slow bridge scans rather than high-rate dynamic measurements, making output settling and filter design central to accurate results.
Recommandé
Precision Thermocouple Interface
The MCP6033-E/SN can provide low-noise amplification for a thermocouple in a low-power temperature instrument. The 0.9 µA typical quiescent current reduces continuous power demand, and rail-to-rail input operation supports the narrow signal range produced by thermocouples. The ±150 µV maximum input offset is meaningful when the thermocouple voltage is small, although input bias current, cold-junction compensation, and error drift must also be included in the overall accuracy budget. Its 10 kHz bandwidth suits thermal measurements with relatively slow response.
Recommandé
Low-Power Current Detection
The MCP6033-E/SN can amplify the voltage generated across a small shunt resistor in a battery monitor or low-current power system. Operating from 1.8 V to 5.5 V allows the amplifier to work directly with low-energy rails, while its 0.9 µA typical quiescent current limits the monitoring circuit's overhead. The ±150 µV maximum offset affects the smallest detectable current, making shunt resistance and error budget important design variables. The 10 kHz bandwidth is appropriate for slow current measurements rather than high-bandwidth pulse monitoring.
Recommandé
Intermittently Powered Analog Front End
The MCP6033-E/SN is well suited to an intermittently powered analog front end because it combines a 0.9 µA typical quiescent current with chip-select capability. According to the Microchip Technology datasheet, CS can place the amplifier into a low-power state when its output is not needed. Rail-to-rail operation preserves useful signal range at low supply voltages, and unity-gain stability simplifies direct buffering. Design the enable sequence so that input and output states remain controlled during startup and shutdown, particularly when the amplifier drives a sampling or multiplexing network.
Recommandé
Récapitulatif des produits recommandés
Données de référence d'ingénierie pour MCP6033-E/SN — comparaison, recommandations de conception et informations de conformité.
Guide de sélection
Comparaison avec les alternatives
| Paramètre | Ce produit | MCP6033T-E/SN |
|---|---|---|
| Brand | Microchip Technology | Microchip Technology |
| Package | 8-SOIC | 8-SOIC |
| Number of Circuits | 1 circuit | 1 circuit |
| Minimum Supply Voltage | 1.8 V | 1.8 V |
| Maximum Supply Voltage | 5.5 V | 5.5 V |
| Gain-Bandwidth Product | 10 kHz typical | 10 kHz typical |
| Quiescent Current | 0.9 µA typical | 0.9 µA typical |
| Input Offset Voltage | ±150 µV maximum | ±150 µV maximum |
| Input Configuration | Rail-to-rail input | Rail-to-rail input |
| Output Configuration | Rail-to-rail output | Rail-to-rail output |
| Slew Rate | 0.004 V/µs | 0.004 V/µs |
| Chip-Select Capability | Yes | Yes |
| Shipping Package | Tube | Tube |
Principaux différenciateurs
- Extremely low quiescent current for an 8-SOIC precision amplifier (vs MCP6033T-E/SN)
- Low-voltage operation with rail-to-rail signal handling (vs MCP6033T-E/SN)
- Precision offset performance for low-level signals (vs MCP6033T-E/SN)
Notes de conception
Use separate supply bypass capacitors close to pins 4 and 7, with a short return path to the amplifier ground. The 0.9 µA typical quiescent current makes capacitor leakage and contamination significant at very low supply voltages; select low-leakage ceramic capacitors and verify their DC-bias derating. Add a supply-decoupling capacitor at the chip-select control pin if the manufacturer guidance calls for it, and keep digital control traces away from the inverting input to avoid coupling.
Route the non-inverting and inverting inputs as short, symmetric traces directly to pins 3 and 2, and place the gain-setting feedback components close to those inputs. Keep the output route at pin 6 separate from the input pair because even a low-frequency amplifier can couple output movement into high-impedance sensor nodes. For thermocouple or bridge measurements, use guarding, differential routing, and a clean reference plane to reduce thermoelectric and leakage-induced errors.
Do not treat the 10 kHz gain-bandwidth product as suitable for high-speed signals. Closed-loop bandwidth, slew-rate-limited settling, and output-capacitive stability must all be checked when the operating gain, signal frequency, or load differs from the unity-gain application. The 0.004 V/µs slew rate also means that large output steps require additional settling time. Confirm that the chip-select state does not create an unexpected output during startup or shutdown.
Informations de conformité
The Microchip Technology device data confirms the low-power precision-amplifier function, 1.8 V to 5.5 V operating range, 8-SOIC package, and tube shipping format. Environmental and material-compliance declarations should be confirmed against the current manufacturer product declaration before qualification.