Texas Instruments

OPA111AM - 8 nV/Hz Precision Op Amp | Texas Instruments

N.º da peça: OPA111AM ✗ Fim de vida
8 nV/Hz maximum at 10 kHz Vdss 1 pA maximum Id TO-99-8 metal can Package
MOQ: 1 |

OPA111AM Visão geral

Texas Instruments OPA111AM is a single-circuit, low-noise precision DiFET operational amplifier with 8 nV/Hz input-voltage noise, 1 pA maximum input bias current, and a 2 MHz nominal unity-gain bandwidth, housed in an 8-pin TO-99 metal-can package. Its 250 µV maximum input offset voltage, 1 µV/°C maximum input offset drift, 120 dB minimum open-loop gain, and 100 dB minimum common-mode rejection support demanding precision signal-chain designs.

A precision operational amplifier is an analog IC that amplifies the difference between two input voltages while providing high gain, low offset, and accurate operation over its specified frequency and temperature range. The OPA111 belongs to the DiFET operational-amplifier hierarchy: DiFET input stage, precision amplifier, voltage-feedback amplifier, and analog integrated circuit. Its exceptionally low input bias current makes it particularly appropriate when measuring currents produced by high-impedance sensors.

The OPA111AM combines low-noise input characteristics with a 2 MHz gain-bandwidth product. Its maximum input-voltage noise density of 8 nV/Hz supports sensitive measurement stages, while the 1 pA maximum bias current limits disturbance of high-impedance sources. The 120 dB minimum open-loop gain improves closed-loop accuracy, and 100 dB minimum common-mode rejection suppresses interference from signals common to both inputs.

The 250 µV maximum offset specification is important for instrumentation designs because input offset appears as an equivalent input error after noise gain is applied. Maximum offset drift of 1 µV/°C also matters when temperature changes are substantial. Designers should therefore evaluate the complete error budget, including resistor mismatch, bias-current effects, noise, offset, and drift, rather than relying on open-loop gain alone.

OPA111AM is suited to precision instrumentation, low-level current measurement, photodiode and other high-impedance sensor interfaces, laboratory measurement equipment, and signal-conditioning circuits. Its 8-pin metal-can construction is mechanically robust for through-hole instrumentation assemblies, but the package is larger than modern surface-mount precision amplifiers and the component is no longer actively manufactured.

For new designs, preserve the eight-pin TO-99 footprint only when maintaining an existing board is essential. Otherwise, evaluate a current precision-amplifier family with a compatible noise, bias-current, offset, supply, and common-mode range. When retaining OPA111AM, verify the pin assignment, supply limits, common-mode range, and stability requirements against the manufacturer datasheet before fabrication.

This page combines the OPA111AM electrical characteristics with obsolete-lifecycle guidance, a focused drop-in candidate from the manufacturer’s related family, and practical guidance for instrumentation, high-impedance sensing, and precision analog design. It helps engineers distinguish true board-level replacement options from newer amplifiers that may require a different footprint or different stability configuration.

Alternativas drop-in para OPA111AM — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

OPA111BM

✅ Drop-In
📦 TO-99-8 metal can
Noise density and nominal gain-bandwidth differ by 0% from OPA111AM; the ordering suffix indicates a different grade or qualification configuration that must be checked against the required operating temperature.

📋 Alternativa de referência (fora do catálogo)

OPA111AM Classificações máximas e características elétricas

Amplifier Type Low-noise precision DiFET operational amplifier
Number of Circuits 1 circuit
Input Voltage Noise Density 8 nV/Hz maximum at 10 kHz
Input Bias Current 1 pA maximum
Input Offset Voltage 250 µV maximum
Input Offset Voltage Drift 1 µV/°C maximum
Open-Loop Gain 120 dB minimum
Common-Mode Rejection Ratio 100 dB minimum
Nominal Unity-Gain Bandwidth 2 MHz
Encapsulamento TO-99-8 metal can
Terminal Count 8 pins
Tipo de montagem Through-hole
Status do ciclo de vida Obsolete

Guia de Configuração de Pinos do OPA111AM to-99-8 metal can

Configuração de pinos para OPA111AM (pacote to-99-8 metal can). Este componente analógico possui pinos de entrada, saída e alimentação. Consulte o datasheet do fabricante para configurações de offset null, compensação e pino de enable. Ideal para circuitos de condicionamento de sinal e amplificadores.

Diagrama de pinagem do pacote to-99-8 metal can para OPA111AM

Nenhum dado detalhado de pinagem disponível para OPA111AM.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

OPA111AM é adequado para 6 aplicaçãos: Precision Current Measurement, Photodiode Signal Conditioning, Laboratory Instrumentation, High-Impedance Sensor Interface, Low-Level Voltage Amplification, Legacy Instrument Repair.

⚡

Precision Current Measurement

OPA111AM fits precision current measurement because its maximum input bias current of 1 pA limits the error introduced when the amplifier senses the voltage across a high-value feedback resistor. Its input-voltage noise density of no more than 8 nV/Hz at 10 kHz also keeps the input-referred noise low. In a transimpedance stage, the device can amplify picoamp-to-nanoamp currents while the 120 dB minimum open-loop gain and 100 dB minimum common-mode rejection improve loop accuracy and disturbance rejection.

🧩

Photodiode Signal Conditioning

OPA111AM is appropriate for photodiode front ends because its 1 pA maximum input bias current produces very little unwanted charge injection into a high-impedance photodiode. The 8 nV/Hz maximum input-voltage noise density helps preserve weak photocurrent signals, while the 2 MHz nominal unity-gain bandwidth supports signal bandwidth beyond audio frequencies. The main design consideration is the feedback-network stability and the need to keep stray capacitance around the sensitive input controlled.

🖥️

Laboratory Instrumentation

OPA111AM suits laboratory instrumentation requiring low noise, low offset, and high open-loop gain in a compact analog signal chain. Its 250 µV maximum input offset voltage and 1 µV/°C maximum drift are manageable when the overall measurement accuracy budget includes them. The 100 dB minimum common-mode rejection ratio helps suppress common-mode interference, while the 2 MHz nominal bandwidth is suitable for slow precision measurements rather than wideband waveform acquisition.

🏭

High-Impedance Sensor Interface

OPA111AM can serve as the first amplifier stage for high-impedance sensors because its maximum input bias current of 1 pA minimizes the voltage error introduced through source resistance. The low 8 nV/Hz maximum input-voltage noise density also reduces the amplifier’s input-referred noise contribution. With 120 dB minimum open-loop gain and 2 MHz nominal unity-gain bandwidth, it fits many slow, high-resolution sensor channels where leakage, offset, and drift dominate measurement quality.

📺

Low-Level Voltage Amplification

OPA111AM is useful for low-level voltage amplification where the 8 nV/Hz maximum input-voltage noise density and 250 µV maximum input offset voltage establish the principal input-referred error terms. Its 120 dB minimum open-loop gain supports accurate closed-loop operation, and the 100 dB minimum common-mode rejection ratio improves rejection of interference shared by both input terminals. The 2 MHz bandwidth is adequate for many instrumentation channels, although offset drift and resistor matching must be included in the total error budget.

🔧

Legacy Instrument Repair

OPA111AM is primarily appropriate for legacy instrument repair where the existing PCB uses the eight-pin TO-99 footprint and reproducing the original electrical behavior is essential. Its 2 MHz nominal unity-gain bandwidth, 8 nV/Hz maximum noise density, and 120 dB minimum open-loop gain preserve the expected operating characteristics of mature analog measurement systems. Because the device is obsolete, procurement should confirm exact suffix, temperature grade, package, condition, and traceability before installation.

Resumo dos produtos recomendados

OPA111BM Same-family legacy TO-99 precision amplifier option Usado em: Precision Current Measurement, Photodiode Signal Conditioning, Laboratory Instrumentation, High-Impedance Sensor Interface, Legacy Instrument Repair OPA132 Precision JFET-input amplifier family alternative Usado em: Precision Current Measurement, High-Impedance Sensor Interface OPA277 Precision low-offset-voltage amplifier family option Usado em: Photodiode Signal Conditioning OPA227 Dual precision amplifier family option Usado em: Laboratory Instrumentation, Low-Level Voltage Amplification OPA209 Precision operational-amplifier family option Usado em: Low-Level Voltage Amplification OPA2111KP OPA-family precision dual-amplifier reference Usado em: Legacy Instrument Repair
What are the key specifications of OPA111AM that engineers should know?
OPA111AM is a single low-noise precision DiFET operational amplifier with 8 nV/Hz maximum input-voltage noise, 1 pA maximum input bias current, 250 µV maximum offset, 1 µV/°C maximum drift, 120 dB minimum open-loop gain, and a 2 MHz nominal unity-gain bandwidth. According to the manufacturer datasheet, the device is packaged in an 8-pin TO-99 metal can. These specifications make it especially useful for precision instrumentation and high-impedance sensor interfaces.
What is OPA111AM and what type of operational amplifier is it?
OPA111AM is a single-circuit, low-noise precision DiFET operational amplifier from Texas Instruments. The manufacturer describes it as a precision monolithic dielectrically isolated FET amplifier intended for critical instrumentation applications. Its 8 nV/Hz maximum noise density, 1 pA maximum input bias current, and 2 MHz nominal gain-bandwidth product place it in the precision, low-leakage amplifier category rather than the general-purpose amplifier category.
What is the input noise and bias current of OPA111AM?
OPA111AM has a maximum input-voltage noise density of 8 nV/Hz at 10 kHz and a maximum input bias current of 1 pA. According to the manufacturer datasheet, the noise specification is 100% tested. The combination is valuable in current-measurement front ends because very low bias current minimizes voltage error across the source impedance, while low noise supports amplification of small signals without an excessive noise floor.
Why is OPA111AM suitable for high-impedance sensor measurements?
OPA111AM is suitable for high-impedance sensor measurements because its maximum input bias current is only 1 pA and its input-voltage noise density is no more than 8 nV/Hz at 10 kHz. According to the manufacturer datasheet, these characteristics support precision instrumentation applications. In a transimpedance or voltage-sensing stage, lower bias current reduces source-loading error, while lower noise improves the readability of small sensor signals.
Where can I download the OPA111AM datasheet PDF?
The OPA111AM manufacturer datasheet can be obtained from the linked Burr-Brown and Texas Instruments document available through the Mouser datasheet address on this page. It defines the DiFET operational amplifier, feature ratings, electrical characteristics, and connection information. Use the pin-description section in that document when assigning the eight TO-99 leads, and confirm the electrical limits against the specific OPA111AM suffix before releasing a production design.
Where can I find the OPA111AM pinout?
The OPA111AM pinout is published in the pin-description table of the manufacturer datasheet for the 8-pin TO-99 metal-can package. Pin assignments must be transcribed from that table because the metal-can package is not represented by a matching pre-stored XAIPART diagram key. Treat pin names as a wiring aid only and verify the exact lead numbering, offset-null connections, supply pins, output, and no-connect lead against the datasheet before assembly.
Is OPA111AM still active or obsolete?
OPA111AM is obsolete and has remained unavailable as a current general-purpose production choice for an extended period. Texas Instruments support discussions describe it as an older Burr-Brown metal-can part that was already obsolete. The component remains relevant for maintenance of legacy instrumentation, but new designs should use a currently supported precision amplifier unless retaining the exact TO-99 footprint is a mandatory mechanical requirement.
Where to buy OPA111AM online?
Use the Request a Quote form on this page to request OPA111AM availability, order quantity, condition, and lead time from XAIPART. Because OPA111AM is obsolete, stock can be limited and availability may depend on legacy inventory or authorized sourcing channels. Provide the target quantity and any required inspection or documentation requirements with the request so procurement can confirm the appropriate supply route.
What is the price of OPA111AM?
Use the Request a Quote form on this page for the current OPA111AM unit price, quantity breaks, currency, and availability. OPA111AM is an obsolete metal-can operational amplifier, so transactional terms can vary with condition, quantity, and inventory status. The form allows procurement to request pricing without relying on a static listing that may no longer represent the part’s current market position.
What is the lead time for OPA111AM?
The current OPA111AM lead time must be confirmed through the Request a Quote form on this page. As an obsolete 8-pin TO-99 operational amplifier, its availability may depend on remaining legacy stock, sourcing inspection, and the requested quantity. State the required delivery date and annual usage on the request so procurement can distinguish immediately available inventory from a longer sourcing or transfer lead time.
Is OPA111AM in stock?
OPA111AM inventory status should be confirmed through the Request a Quote form on this page rather than inferred from an archived distributor listing. The manufacturer discontinued the part, so stock may be limited, variable, or tied to a specific sourcing batch. Request quantity, target date, and acceptable condition when asking for availability, particularly for maintenance, repair, or long-life industrial programs.
What is the best drop-in replacement for OPA111AM?
OPA111BM is the closest documented drop-in candidate in the same Texas Instruments OPA111 family because it retains the legacy precision-amplifier architecture and package family. Its distinguishing factor is the ordering suffix rather than the core 8 nV/Hz noise and 2 MHz bandwidth ratings. Because the exact temperature grade and lead configuration must be confirmed, review the manufacturer comparison information before substituting it into production equipment.
Can OPA111BM replace OPA111AM on an existing PCB?
OPA111BM can be considered for replacing OPA111AM when the original board uses the compatible eight-pin TO-99 OPA111 footprint and the required temperature grade is acceptable. The core noise-density and gain-bandwidth ratings remain equivalent, giving a 0% difference in those two headline parameters. Verify supply voltage, common-mode range, offset limits, pin assignments, and temperature grade against the manufacturer documentation before approving the substitution.
When should I choose OPA111AM over a newer precision amplifier?
Choose OPA111AM only when maintaining an existing TO-99 instrumentation design, reproducing a proven measurement module, or qualifying an exact legacy configuration is more important than obtaining a current, smaller package. Its 8 nV/Hz noise and 1 pA maximum bias current remain useful for high-impedance signals, but the obsolete lifecycle, through-hole metal-can format, and aged availability create lifecycle and assembly disadvantages for new designs.
OPA111AM vs OPA111BM: which is better for legacy instrumentation?
OPA111AM versus OPA111BM is primarily a grade and lifecycle decision rather than a headline-noise decision. Both belong to the same low-noise precision DiFET family and are associated with 8 nV/Hz maximum noise and a 2 MHz nominal unity-gain bandwidth. Choose the ordering suffix whose temperature rating and lifecycle status match the equipment being maintained, then verify every limit against the datasheet and the existing circuit’s supply and grounding arrangement.

Dados de referência de engenharia para OPA111AM — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose OPA111AM when repairing or reproducing legacy instrumentation that requires the original eight-pin TO-99 footprint, low input bias current, and established precision behavior. OPA111BM is the closest same-family drop-in candidate because the package and principal 8 nV/Hz noise, 1 pA bias-current, and 2 MHz bandwidth ratings align; confirm the temperature grade and operating limits before substituting it. For a new design, prefer a currently supported precision amplifier unless the TO-99 mechanical footprint is mandatory. Modern alternatives may offer smaller packages, rail-to-rail inputs, lower offset, or higher bandwidth, but they are not automatic drop-in replacements. The decisive checks are pin configuration, supply range, common-mode range, output swing, stability with the selected feedback network, noise, bias current, offset drift, temperature grade, and long-term availability.

Comparação com alternativas

Parâmetro Este produto OPA111BM
Package TO-99-8 metal can TO-99-8 metal can
Brand Texas Instruments Texas Instruments
Amplifier Architecture Low-noise precision DiFET operational amplifier Low-noise precision DiFET operational amplifier
Number of Circuits 1 circuit 1 circuit
Input Voltage Noise Density 8 nV/Hz maximum at 10 kHz 8 nV/Hz maximum at 10 kHz
Input Bias Current 1 pA maximum 1 pA maximum
Input Offset Voltage 250 µV maximum 250 µV maximum
Input Offset Voltage Drift 1 µV/°C maximum 1 µV/°C maximum
Open-Loop Gain 120 dB minimum 120 dB minimum
Common-Mode Rejection Ratio 100 dB minimum 100 dB minimum
Nominal Unity-Gain Bandwidth 2 MHz 2 MHz

Principais diferenciais

  • Exceptionally low input bias current supports high-impedance measurement (vs OPA111BM)
  • Low-noise input stage is suitable for weak sensor signals (vs OPA111BM)
  • Legacy TO-99 construction simplifies mechanical preservation (vs OPA111BM)
  • Gain-bandwidth balance favors precision instrumentation (vs OPA111BM)

Notas de projeto

Do not substitute OPA111AM solely because another low-noise amplifier has a similar headline specification. Verify the eight-pin TO-99 lead arrangement, supply voltage, input common-mode range, output swing, offset limits, compensation requirements, and operating-temperature grade. OPA111AM uses a metal-can package with lead spacing and mechanical height that differ from modern surface-mount devices, so an electrically similar amplifier may still require a PCB redesign.

For OPA111AM layouts, keep the sensitive input lead and feedback components short and place compensation components close to the amplifier pins. Maintain a stable low-impedance ground return and avoid routing the input beside high-current switching nodes. Because the maximum input bias current is only 1 pA, preserve clean board insulation and avoid flux residue or moisture paths that could introduce leakage comparable to the intended sensor current.

Include offset, drift, bias-current error, noise, and resistor tolerance in the closed-loop error budget. For a transimpedance stage, the bias-current-induced error is approximately the input bias current multiplied by total resistance seen at the input, while output offset is multiplied by the noise gain. The 250 µV maximum offset and 1 µV/°C maximum drift from the manufacturer datasheet can therefore become significant after high noise-gain multiplication.

Check the amplifier’s supply dissipation and the metal-can temperature rise under the actual operating condition. The metal can provides a stable mechanical mount and thermal path, but its operating-temperature limits still apply. Use the manufacturer electrical-characteristics tables for maximum supply voltage, output swing, and temperature limits. For long-life industrial equipment, pay particular attention to temperature drift because 1 µV/°C can materially affect a precision measurement after noise-gain multiplication.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

OPA111AM is an obsolete legacy TO-99 precision operational amplifier. No current RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited manufacturer and distributor materials.

Dados verificados em: 2026-11-19 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

OPA111AM datasheet OPA111AM pinout OPA111AM datasheet pdf OPA111AM specifications OPA111AM TO-99-8 OPA111AM equivalent OPA111AM replacement OPA111AM cross reference OPA111AM vs OPA111BM OPA111AM low noise op amp OPA111AM precision instrumentation OPA111AM price OPA111AM stock Texas Instruments OPA111AM

Componentes & termos relacionados

Texas Instruments OPA111AM OPA111BM OPA111 precision operational amplifier DiFET operational amplifier low-noise amplifier voltage-feedback amplifier analog integrated circuit input-voltage noise density input bias current input offset voltage input offset drift unity-gain bandwidth common-mode rejection ratio open-loop gain TO-99-8 metal can metal-can package through-hole mounting precision instrumentation transimpedance amplifier high-impedance sensor photodiode legacy equipment repair obsolete component
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ