OPA111AM - 8 nV/Hz Precision Op Amp | Texas Instruments
MPN: OPA111AM ✗ اختتامِ زندگیOPA111AM جائزہ
A precision operational amplifier is an analog IC that amplifies the difference between two input voltages while providing high gain, low offset, and accurate operation over its specified frequency and temperature range. The OPA111 belongs to the DiFET operational-amplifier hierarchy: DiFET input stage, precision amplifier, voltage-feedback amplifier, and analog integrated circuit. Its exceptionally low input bias current makes it particularly appropriate when measuring currents produced by high-impedance sensors.
The OPA111AM combines low-noise input characteristics with a 2 MHz gain-bandwidth product. Its maximum input-voltage noise density of 8 nV/Hz supports sensitive measurement stages, while the 1 pA maximum bias current limits disturbance of high-impedance sources. The 120 dB minimum open-loop gain improves closed-loop accuracy, and 100 dB minimum common-mode rejection suppresses interference from signals common to both inputs.
The 250 µV maximum offset specification is important for instrumentation designs because input offset appears as an equivalent input error after noise gain is applied. Maximum offset drift of 1 µV/°C also matters when temperature changes are substantial. Designers should therefore evaluate the complete error budget, including resistor mismatch, bias-current effects, noise, offset, and drift, rather than relying on open-loop gain alone.
OPA111AM is suited to precision instrumentation, low-level current measurement, photodiode and other high-impedance sensor interfaces, laboratory measurement equipment, and signal-conditioning circuits. Its 8-pin metal-can construction is mechanically robust for through-hole instrumentation assemblies, but the package is larger than modern surface-mount precision amplifiers and the component is no longer actively manufactured.
For new designs, preserve the eight-pin TO-99 footprint only when maintaining an existing board is essential. Otherwise, evaluate a current precision-amplifier family with a compatible noise, bias-current, offset, supply, and common-mode range. When retaining OPA111AM, verify the pin assignment, supply limits, common-mode range, and stability requirements against the manufacturer datasheet before fabrication.
This page combines the OPA111AM electrical characteristics with obsolete-lifecycle guidance, a focused drop-in candidate from the manufacturer’s related family, and practical guidance for instrumentation, high-impedance sensing, and precision analog design. It helps engineers distinguish true board-level replacement options from newer amplifiers that may require a different footprint or different stability configuration.
کے لیے ڈراپ اِن متبادل OPA111AM — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
OPA111BM
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
OPA111AM زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | Low-noise precision DiFET operational amplifier |
| Number of Circuits | 1 circuit |
| Input Voltage Noise Density | 8 nV/Hz maximum at 10 kHz |
| Input Bias Current | 1 pA maximum |
| Input Offset Voltage | 250 µV maximum |
| Input Offset Voltage Drift | 1 µV/°C maximum |
| Open-Loop Gain | 120 dB minimum |
| Common-Mode Rejection Ratio | 100 dB minimum |
| Nominal Unity-Gain Bandwidth | 2 MHz |
| پیکیج | TO-99-8 metal can |
| Terminal Count | 8 pins |
| ماؤنٹنگ ٹائپ | Through-hole |
| لائف سائیکل کی حالت | Obsolete |
OPA111AM to-99-8 metal can پن کنفیگریشن گائیڈ
OPA111AM (to-99-8 metal can پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں OPA111AM.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
OPA111AM کے لیے موزوں ہے 6 ایپلیکیشنs: Precision Current Measurement, Photodiode Signal Conditioning, Laboratory Instrumentation, High-Impedance Sensor Interface, Low-Level Voltage Amplification, Legacy Instrument Repair.
Precision Current Measurement
OPA111AM fits precision current measurement because its maximum input bias current of 1 pA limits the error introduced when the amplifier senses the voltage across a high-value feedback resistor. Its input-voltage noise density of no more than 8 nV/Hz at 10 kHz also keeps the input-referred noise low. In a transimpedance stage, the device can amplify picoamp-to-nanoamp currents while the 120 dB minimum open-loop gain and 100 dB minimum common-mode rejection improve loop accuracy and disturbance rejection.
تجویز کردہ
Photodiode Signal Conditioning
OPA111AM is appropriate for photodiode front ends because its 1 pA maximum input bias current produces very little unwanted charge injection into a high-impedance photodiode. The 8 nV/Hz maximum input-voltage noise density helps preserve weak photocurrent signals, while the 2 MHz nominal unity-gain bandwidth supports signal bandwidth beyond audio frequencies. The main design consideration is the feedback-network stability and the need to keep stray capacitance around the sensitive input controlled.
تجویز کردہ
Laboratory Instrumentation
OPA111AM suits laboratory instrumentation requiring low noise, low offset, and high open-loop gain in a compact analog signal chain. Its 250 µV maximum input offset voltage and 1 µV/°C maximum drift are manageable when the overall measurement accuracy budget includes them. The 100 dB minimum common-mode rejection ratio helps suppress common-mode interference, while the 2 MHz nominal bandwidth is suitable for slow precision measurements rather than wideband waveform acquisition.
تجویز کردہ
High-Impedance Sensor Interface
OPA111AM can serve as the first amplifier stage for high-impedance sensors because its maximum input bias current of 1 pA minimizes the voltage error introduced through source resistance. The low 8 nV/Hz maximum input-voltage noise density also reduces the amplifier’s input-referred noise contribution. With 120 dB minimum open-loop gain and 2 MHz nominal unity-gain bandwidth, it fits many slow, high-resolution sensor channels where leakage, offset, and drift dominate measurement quality.
تجویز کردہ
Low-Level Voltage Amplification
OPA111AM is useful for low-level voltage amplification where the 8 nV/Hz maximum input-voltage noise density and 250 µV maximum input offset voltage establish the principal input-referred error terms. Its 120 dB minimum open-loop gain supports accurate closed-loop operation, and the 100 dB minimum common-mode rejection ratio improves rejection of interference shared by both input terminals. The 2 MHz bandwidth is adequate for many instrumentation channels, although offset drift and resistor matching must be included in the total error budget.
تجویز کردہ
Legacy Instrument Repair
OPA111AM is primarily appropriate for legacy instrument repair where the existing PCB uses the eight-pin TO-99 footprint and reproducing the original electrical behavior is essential. Its 2 MHz nominal unity-gain bandwidth, 8 nV/Hz maximum noise density, and 120 dB minimum open-loop gain preserve the expected operating characteristics of mature analog measurement systems. Because the device is obsolete, procurement should confirm exact suffix, temperature grade, package, condition, and traceability before installation.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا OPA111AM — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | OPA111BM |
|---|---|---|
| Package | TO-99-8 metal can | TO-99-8 metal can |
| Brand | Texas Instruments | Texas Instruments |
| Amplifier Architecture | Low-noise precision DiFET operational amplifier | Low-noise precision DiFET operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit |
| Input Voltage Noise Density | 8 nV/Hz maximum at 10 kHz | 8 nV/Hz maximum at 10 kHz |
| Input Bias Current | 1 pA maximum | 1 pA maximum |
| Input Offset Voltage | 250 µV maximum | 250 µV maximum |
| Input Offset Voltage Drift | 1 µV/°C maximum | 1 µV/°C maximum |
| Open-Loop Gain | 120 dB minimum | 120 dB minimum |
| Common-Mode Rejection Ratio | 100 dB minimum | 100 dB minimum |
| Nominal Unity-Gain Bandwidth | 2 MHz | 2 MHz |
اہم امتیازی خصوصیات
- Exceptionally low input bias current supports high-impedance measurement (بمقابلہOPA111BM)
- Low-noise input stage is suitable for weak sensor signals (بمقابلہOPA111BM)
- Legacy TO-99 construction simplifies mechanical preservation (بمقابلہOPA111BM)
- Gain-bandwidth balance favors precision instrumentation (بمقابلہOPA111BM)
ڈیزائن نوٹس
Do not substitute OPA111AM solely because another low-noise amplifier has a similar headline specification. Verify the eight-pin TO-99 lead arrangement, supply voltage, input common-mode range, output swing, offset limits, compensation requirements, and operating-temperature grade. OPA111AM uses a metal-can package with lead spacing and mechanical height that differ from modern surface-mount devices, so an electrically similar amplifier may still require a PCB redesign.
For OPA111AM layouts, keep the sensitive input lead and feedback components short and place compensation components close to the amplifier pins. Maintain a stable low-impedance ground return and avoid routing the input beside high-current switching nodes. Because the maximum input bias current is only 1 pA, preserve clean board insulation and avoid flux residue or moisture paths that could introduce leakage comparable to the intended sensor current.
Include offset, drift, bias-current error, noise, and resistor tolerance in the closed-loop error budget. For a transimpedance stage, the bias-current-induced error is approximately the input bias current multiplied by total resistance seen at the input, while output offset is multiplied by the noise gain. The 250 µV maximum offset and 1 µV/°C maximum drift from the manufacturer datasheet can therefore become significant after high noise-gain multiplication.
Check the amplifier’s supply dissipation and the metal-can temperature rise under the actual operating condition. The metal can provides a stable mechanical mount and thermal path, but its operating-temperature limits still apply. Use the manufacturer electrical-characteristics tables for maximum supply voltage, output swing, and temperature limits. For long-life industrial equipment, pay particular attention to temperature drift because 1 µV/°C can materially affect a precision measurement after noise-gain multiplication.
تعمیل کی معلومات
OPA111AM is an obsolete legacy TO-99 precision operational amplifier. No current RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified in the cited manufacturer and distributor materials.