NXP Semiconductors

PCA9539BSHP - 16-Bit 400kHz I/O Expander | NXP

N.º da peça: PCA9539BSHP ✓ Ativo
5.5 V Vdss 24-pin HVQFN, 4 x 4 mm Package 400 kHz Speed
MOQ: 1 |

PCA9539BSHP Visão geral

The NXP Semiconductors PCA9539BSHP is a 16-bit low-power I2C-bus and SMBus GPIO expander operating at up to 400 kHz in a 24-pin HVQFN package with a 4 x 4 mm body and exposed thermal pad. It provides 16 general-purpose input/output pins, an interrupt output, and a reset function for systems requiring more GPIO than the host controller can directly provide.

An I2C GPIO expander is an interface IC that extends the input/output capacity of a host processor through a serial bus. The PCA9539BSHP belongs to the GPIO expander hierarchy, where serial I2C communication controls parallel digital ports. This approach reduces the number of pins required on a microcontroller, embedded system, or control board while allowing switches, LEDs, sensors, and other digital loads to connect through one bus.

The device supports both 100 kHz and 400 kHz I2C operation. Its 16 I/O pins can be configured for digital input or output, while the interrupt and reset functions support event-driven host communication and orderly state recovery. The low-power design is particularly useful in embedded equipment where bus idle current, board area, and external wiring complexity are important design constraints.

The PCA9539BSHP is a 24-pin CMOS device based on the NXP PCA9539 family of low-power I/O port expanders. It combines parallel GPIO capability with serial control and is designed for I2C-bus and SMBus applications. The HVQFN package also provides an exposed pad that can improve heat transfer when the device is mounted on a PCB with suitable copper and thermal layout.

Typical uses include ACPI power-switch control, sensor interfaces, push-button inputs, status indicators, and fan or LED control. Its 16-bit port width makes it useful when several related digital signals must be grouped behind an I2C bus rather than connected individually to the host processor. A system designer can place the expander near the controlled peripherals and route compact serial signals back to the main controller.

PCB design should preserve short I2C routing, common ground connectivity, and appropriate pull-up placement. The exposed thermal pad should be connected to the ground plane and thermal-via pattern specified in the NXP package documentation. Firmware must also configure each port direction, mask unwanted interrupts, and account for the device address and reset behavior before external signals are enabled.

This product page combines the verified ordering information, functional characteristics, application guidance, package constraints, and replacement limitations for PCA9539BSHP. It also highlights where engineers should compare exact pin compatibility, bus address behavior, and power characteristics rather than treating every 16-bit I/O expander as a direct substitution.

Alternativas drop-in para PCA9539BSHP — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

PCA9539BS

✅ Drop-In
📦 24-pin HVQFN, 4 x 4 mm
Same 16-bit I/O, 400 kHz I2C, interrupt, and reset functions; exact suffix-specific rating and lifecycle details require confirmation.

📋 Alternativa de referência (fora do catálogo)

PCA9539BSHP Especificações

Number of I/O Ports 16 bits
I2C Maximum Clock Frequency 400 kHz
I2C Supported Frequencies 100 kHz and 400 kHz
Bus Interface I2C-bus and SMBus
Encapsulamento 24-pin HVQFN, 4 x 4 mm
Contagem de pinos 24 pins
Device Type Low-power 16-bit GPIO expander
Interrupt Function Yes
Reset Function Yes
Maximum Supply Voltage 5.5 V
Automotive Qualification Automotive
Tipo de montagem Surface mount
Exposed Pad Yes
Packaging Tape and reel

Guia de Configuração de Pinos do PCA9539BSHP 24-pin hvqfn, 4 x 4 mm

Configuração de pinos para PCA9539BSHP (pacote 24-pin hvqfn, 4 x 4 mm). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.

Diagrama de pinagem do pacote 24-pin hvqfn, 4 x 4 mm para PCA9539BSHP

Nenhum dado detalhado de pinagem disponível para PCA9539BSHP.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

PCA9539BSHP é adequado para 6 aplicaçãos: ACPI Power-Switch Control, Industrial Sensor and Button Interface, LED and Status-Indicator Control, Fan and Peripheral-Switch Control, Embedded Control Module, Server and Networking Control.

⚡

ACPI Power-Switch Control

The PCA9539BSHP fits ACPI control boards that need multiple power-related signals without consuming a comparable number of host-controller pins. Its 16 general-purpose I/O bits operate from an I2C or SMBus connection at up to 400 kHz, while interrupt and reset functions help the host coordinate state changes. Placing the expander close to the power-switch circuitry keeps those routes short and limits the number of traces returning to the processor. Firmware can configure individual outputs for switch control, read back applicable status lines, and use the interrupt output to report events instead of continuously polling every port.

🏭

Industrial Sensor and Button Interface

PCA9539BSHP is useful when an industrial controller must collect several digital sensor states or user-button inputs while preserving host-processor pins for timing and communication tasks. Its 16 I/O bits provide a single logical port, and 400 kHz I2C operation supports efficient host updates. The interrupt function allows the controller to react to a changed input rather than repeatedly polling the entire port. Because the device operates from a compact HVQFN package, it can be positioned near remote connectors and front-panel switches, reducing wiring complexity while maintaining a shared serial connection to the main controller.

💡

LED and Status-Indicator Control

The PCA9539BSHP can drive or monitor grouped LED and status-indicator signals through its 16 configurable I/O bits. I2C control at up to 400 kHz allows the host to update multiple indicators during a short transaction, while the interrupt path can support inputs from buttons or status switches. The 4 x 4 mm HVQFN body saves board area compared with many discrete digital-control packages. In multi-LED designs, current limiting and polarity still belong in the external circuit, and firmware should account for the electrical limits of every port before changing an input to an output.

🔧

Fan and Peripheral-Switch Control

PCA9539BSHP fits control boards that operate several fans, relays, or peripheral enable signals alongside a host processor. Its 16-bit parallel I/O capability groups related controls behind an I2C-bus interface, and the interrupt output can report applicable switch or fault events. Running the bus at 100 kHz or 400 kHz provides flexibility for both conventional and faster embedded control networks. Because the device is a low-power I/O expander rather than a power driver, external transistor or driver stages are required for loads whose current exceeds the device's output capability.

🧩

Embedded Control Module

The PCA9539BSHP is suitable for compact embedded modules that need more host-visible digital lines than the local controller can expose directly. Its 24-pin HVQFN package provides 16 I/O bits in a small footprint, while I2C or SMBus transport reduces connector and routing requirements between the host and peripheral logic. The interrupt line supports event-driven host wake-up or service routines, and reset provides a defined recovery mechanism for the port state. Firmware initialization should configure direction, masks, polarity, and the device address before external equipment is activated.

🖥️

Server and Networking Control

PCA9539BSHP can extend a server or networking card with service LEDs, connector-present signals, reset controls, and other discrete digital functions. A 16-bit port provides a practical way to consolidate multiple low-speed signals over I2C, while 400 kHz operation supports timely updates without occupying a large number of processor pins. Interrupt and reset functions are useful when the management controller must respond to external events or restore deterministic port states. In server applications, the exact electrical limits, environmental requirements, and package layout must be reviewed against the system specification before deployment.

Resumo dos produtos recomendados

PCA9539BS Same-family 16-bit I/O expander Usado em: ACPI Power-Switch Control, Industrial Sensor and Button Interface, LED and Status-Indicator Control, Fan and Peripheral-Switch Control, Embedded Control Module, Server and Networking Control PCA9539PW NXP Semiconductors Usado em: ACPI Power-Switch Control, Industrial Sensor and Button Interface, LED and Status-Indicator Control, Fan and Peripheral-Switch Control, Embedded Control Module, Server and Networking Control
What is the PCA9539BSHP used for?
The PCA9539BSHP is a 16-bit low-power I2C-bus and SMBus GPIO expander for adding parallel digital input/output capability to a host processor. It provides 16 general-purpose I/O pins together with interrupt and reset functions. According to the NXP product information, typical uses include ACPI power switches, sensors, push buttons, LEDs, and fans, allowing these peripherals to share a compact serial interface.
How many I/O pins does the PCA9539BSHP have?
The PCA9539BSHP provides 16 general-purpose parallel input/output bits. Each I/O can be used as an input or output according to its configured direction, making the device suitable for grouping switches, indicators, and control signals behind an I2C or SMBus connection. The NXP product information identifies it as a 24-pin CMOS device with 16 bits of GPIO expansion, interrupt, and reset.
What is the maximum I2C clock frequency of PCA9539BSHP?
The PCA9539BSHP supports I2C operation at 100 kHz and up to 400 kHz. The maximum rate of 400 kHz is identified in the verified ordering information for the PCA9539BSHP. Designers should ensure that pull-up resistance, bus capacitance, wiring length, and the connected host controller all support the selected operating speed.
What package does the PCA9539BSHP use?
The PCA9539BSHP uses a 24-pin HVQFN package with a 4 x 4 mm body and an exposed pad. According to NXP ordering information, the PCA9539BSHP is supplied in a tape-and-reel format. The exposed pad requires the PCB land pattern and thermal-via arrangement described in the manufacturer package documentation.
Where can I download the PCA9539BSHP datasheet?
The official NXP PCA9539BS product page is the correct starting point for the manufacturer datasheet and supporting documentation. It covers the PCA9539 family and the PCA9539BS ordering variant. Use the NXP documentation links to download the current datasheet, package drawing, errata, and any revision-specific application information before releasing a PCB.
Where can I find the PCA9539BSHP pinout?
The PCA9539BSHP pin assignment is defined in the pin-description table and package drawing in the NXP datasheet. Because the 24-pin HVQFN footprint includes an exposed pad and the verified listing does not reproduce every terminal name, the exact pin mapping should be taken directly from the manufacturer document. Start pin 1 at the package marker and follow the diagram shown in the selected package drawing.
Can PCA9539BS replace PCA9539BSHP?
The PCA9539BS is the closest same-family ordering variant and is the most practical candidate to evaluate when the PCA9539BSHP is unavailable. NXP describes both as 24-pin CMOS devices with 16 GPIO bits, interrupt, and reset. Before substitution, confirm that the exact package, thermal-pad land pattern, pinout, address configuration, and electrical limits match the PCA9539BSHP revision being replaced.
What is a drop-in replacement for PCA9539BSHP?
No five-part drop-in replacement set could be confirmed from the available manufacturer and distributor information. The PCA9539BS is the closest same-family candidate, but exact pin and package equivalence should still be checked against the NXP datasheet before use. Other 16-bit I2C expanders may provide similar functionality without sharing the HVQFN footprint, so they cannot automatically be treated as board-level drop-ins.
Is there a Texas Instruments equivalent to PCA9539BSHP?
The Texas Instruments PCA9539 is a functionally close I2C GPIO-expander alternative with 16 I/O pins, interrupt support, and low power consumption. However, the verified material does not establish that its package and pin arrangement are identical to the 24-pin HVQFN PCA9539BSHP. Treat it as a functional comparison rather than a confirmed footprint-compatible substitute unless the package drawing and pin table are checked directly.
PCA9539BSHP vs PCA9539BS - which should I choose?
Choose PCA9539BSHP when the design specifically requires the NXP HVQFN ordering variant, while PCA9539BS should be checked as the closest family alternative when that exact suffix needs consolidation. Both devices are identified as 24-pin CMOS devices providing 16 GPIO bits with interrupt and reset. The final choice depends on exact package drawing, pinout, address behavior, temperature grade, and lifecycle requirements.
When should I choose PCA9539BSHP over another 16-bit I/O expander?
Choose PCA9539BSHP when the PCB already uses its 24-pin HVQFN footprint and the design needs 16 I2C-controlled GPIO bits with interrupt and reset functions. Retain this part when firmware, pin mapping, thermal layout, and qualification are already validated. Choose a different expander when its package, address scheme, voltage range, or interface features allow a PCB or firmware improvement.
Is PCA9539BSHP suitable for sensors and push buttons?
Yes, the PCA9539BSHP is suitable for digital sensors, push buttons, ACPI power switches, LEDs, and fan-control signals because it provides 16 general-purpose I/O bits behind an I2C or SMBus interface. The interrupt output can reduce unnecessary host polling when a monitored input changes. Firmware must configure the relevant pins and interrupt mask before enabling the associated application functions.
Where can I buy PCA9539BSHP and check its lead time?
Use the Request a Quote form on this page to request the current PCA9539BSHP price, stock position, lead time, and order quantity. Quote-based handling is appropriate because availability and commercial terms can change independently of the device specifications. Provide the target quantity and package suffix PCA9539BSHP when submitting the request.
How much does PCA9539BSHP cost and is it in stock?
Current PCA9539BSHP pricing and stock status should be obtained through the Request a Quote form on this page. The form is the source for the current commercial offer and lead time rather than a static price statement. Include the required quantity, reel quantity, and target assembly schedule so the supplier can confirm the appropriate configuration.
What are the key specifications of PCA9539BSHP that engineers should know?
The key PCA9539BSHP specifications are 16 general-purpose I/O bits, I2C-bus and SMBus support, operation at 100 kHz or 400 kHz, interrupt and reset functions, and a 24-pin 4 x 4 mm HVQFN package. NXP also identifies the device as low-power and automotive. These parameters define its use as a compact parallel-port extension for embedded control systems.
What can replace the PCA9539BSHP?
PCA9539BS is the closest confirmed same-family replacement candidate because NXP describes it as a 24-pin CMOS version of the PCA9539 with 16 GPIO bits, interrupt, and reset. Its exact suffix, package, and footprint must still be reconciled with the PCA9539BSHP before production use. No additional part was confirmed as both pin-to-pin compatible and housed in the same HVQFN package.
Is the PCA9539BSHP the same as the PCA9539PW?
No, the PCA9539BSHP and PCA9539PW belong to the same functional family but use different package options. The PCA9539BSHP is listed in a 24-pin HVQFN package with a 4 x 4 mm body, while NXP identifies the PCA9539PW as a 24-pin TSSOP24 version. They can support similar designs, but PCA9539PW is not a direct footprint-compatible replacement for PCA9539BSHP.

Dados de referência de engenharia para PCA9539BSHP — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose the PCA9539BSHP for an existing or new design that specifically uses the NXP 24-pin HVQFN footprint and requires 16 configurable I/O bits, I2C operation at up to 400 kHz, and interrupt and reset functions. Consider PCA9539BS as the closest same-family consolidation option after checking its exact package drawing, pinout, electrical limits, address behavior, and qualification. The PCA9539PW is useful for a redesigned board that can use TSSOP24, but it is not a footprint-compatible substitute. A functionally similar 16-bit expander from another manufacturer should be selected only when its package, pinout, address scheme, voltage range, and interrupt behavior have been verified against the PCB requirements.

Comparação com alternativas

Parâmetro Este produto PCA9539BS
Brand NXP Semiconductors NXP Semiconductors
Package 24-pin HVQFN, 4 x 4 mm 24-pin HVQFN family option; exact drawing requires confirmation
Number of I/O Ports 16 bits 16 bits
Bus Interface I2C-bus and SMBus I2C-bus and SMBus
Maximum I2C Clock Frequency 400 kHz 400 kHz
Supported I2C Frequencies 100 kHz and 400 kHz 100 kHz and 400 kHz
Interrupt Function Yes Yes
Reset Function Yes Yes
Device Technology 24-pin CMOS low-power I/O expander 24-pin CMOS low-power I/O expander

Principais diferenciais

  • Provides 16 configurable I/O bits behind one serial bus (vs PCA9539BS)
  • Supports event-driven host updates through an interrupt output (vs PCA9539BS)
  • Combines compact 4 x 4 mm HVQFN packaging with 16 I/O (vs PCA9539PW)

Notas de projeto

Follow the NXP HVQFN land pattern rather than approximating it from a generic QFN footprint. Connect the exposed thermal pad to the intended ground plane and add the recommended thermal-via pattern to improve heat transfer. Keep I2C traces short, route the clock and data away from high-current switching nodes, and place bus pull-up resistors where they maintain an effective resistance with the actual bus capacitance and total connected load.

Place the PCA9539BSHP near the connector, switch bank, indicator group, or other remote I/O loads that it serves. This minimizes trace lengths on the 16 parallel port lines while allowing the I2C clock, data, interrupt, and reset routes to remain compact. Provide a continuous ground reference beneath the device and isolate sensitive analog or high-speed routes from the connector-side switching currents.

Do not assume that every PCA9539-family ordering suffix has identical address behavior, package construction, or qualification. Confirm the device address, reset polarity, port default state, operating-voltage range, output-current limits, and pin assignment for the exact suffix in the NXP documentation. Firmware should also wait for a valid bus response and initialize port direction and interrupt masks before external loads begin switching.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The verified product information identifies PCA9539BSHP as automotive, but it does not expressly state RoHS, REACH, AEC-Q100 qualification, lead-free, halogen-free, or conflict-minerals status.

Dados verificados em: 2026-11-14 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

PCA9539BSHP datasheet PCA9539BSHP pinout PCA9539BSHP datasheet pdf PCA9539BSHP equivalent PCA9539BSHP replacement PCA9539BSHP cross reference PCA9539BSHP price PCA9539BSHP stock PCA9539BSHP footprint PCA9539BSHP application circuit PCA9539BSHP vs PCA9539BS PCA9539BS vs PCA9539BSHP NXP PCA9539BSHP PCA9539 16-bit 400kHz I/O expander PCA9539BSHP schematic

Componentes & termos relacionados

NXP Semiconductors PCA9539BSHP PCA9539BS PCA9539PW PCA9539 GPIO expander I/O expander 16-bit parallel I/O I2C-bus SMBus embedded system host processor microcontroller interrupt output reset function low-power CMOS HVQFN-24 QFN family surface-mount package exposed thermal pad digital sensor interface push-button input LED control ACPI power-switch control
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ