PCA9539BSHP - 16-Bit 400kHz I/O Expander | NXP
MPN: PCA9539BSHP ✓ פעילPCA9539BSHP סקירה
An I2C GPIO expander is an interface IC that extends the input/output capacity of a host processor through a serial bus. The PCA9539BSHP belongs to the GPIO expander hierarchy, where serial I2C communication controls parallel digital ports. This approach reduces the number of pins required on a microcontroller, embedded system, or control board while allowing switches, LEDs, sensors, and other digital loads to connect through one bus.
The device supports both 100 kHz and 400 kHz I2C operation. Its 16 I/O pins can be configured for digital input or output, while the interrupt and reset functions support event-driven host communication and orderly state recovery. The low-power design is particularly useful in embedded equipment where bus idle current, board area, and external wiring complexity are important design constraints.
The PCA9539BSHP is a 24-pin CMOS device based on the NXP PCA9539 family of low-power I/O port expanders. It combines parallel GPIO capability with serial control and is designed for I2C-bus and SMBus applications. The HVQFN package also provides an exposed pad that can improve heat transfer when the device is mounted on a PCB with suitable copper and thermal layout.
Typical uses include ACPI power-switch control, sensor interfaces, push-button inputs, status indicators, and fan or LED control. Its 16-bit port width makes it useful when several related digital signals must be grouped behind an I2C bus rather than connected individually to the host processor. A system designer can place the expander near the controlled peripherals and route compact serial signals back to the main controller.
PCB design should preserve short I2C routing, common ground connectivity, and appropriate pull-up placement. The exposed thermal pad should be connected to the ground plane and thermal-via pattern specified in the NXP package documentation. Firmware must also configure each port direction, mask unwanted interrupts, and account for the device address and reset behavior before external signals are enabled.
This product page combines the verified ordering information, functional characteristics, application guidance, package constraints, and replacement limitations for PCA9539BSHP. It also highlights where engineers should compare exact pin compatibility, bus address behavior, and power characteristics rather than treating every 16-bit I/O expander as a direct substitution.
חלופות תחליף ישיר עבור PCA9539BSHP — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.
PCA9539BS
✅ Drop-In📋 חלופה להתייחסות (לא בקטלוג)
PCA9539BSHP מפרטים
| Number of I/O Ports | 16 bits |
| I2C Maximum Clock Frequency | 400 kHz |
| I2C Supported Frequencies | 100 kHz and 400 kHz |
| Bus Interface | I2C-bus and SMBus |
| מארז | 24-pin HVQFN, 4 x 4 mm |
| מספר פינים | 24 pins |
| Device Type | Low-power 16-bit GPIO expander |
| Interrupt Function | Yes |
| Reset Function | Yes |
| Maximum Supply Voltage | 5.5 V |
| Automotive Qualification | Automotive |
| סוג הרכבה | Surface mount |
| Exposed Pad | Yes |
| Packaging | Tape and reel |
מדריך תצורת פינים של PCA9539BSHP 24-pin hvqfn, 4 x 4 mm
תצורת פינים עבור PCA9539BSHP (מארזת 24-pin hvqfn, 4 x 4 mm). מספרי פינים, פונקציות ותרשימי חיבורים מוגדרים ב-Datasheet של היצרן. יש לעיין בו לקבלת ה-footprint המדויק והנחיות הלחמה.
אין נתוני פריסת פינים מפורטים עבור PCA9539BSHP.
עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.
יישומים טיפוסיים
PCA9539BSHP מתאים עבור 6 יישוםs: ACPI Power-Switch Control, Industrial Sensor and Button Interface, LED and Status-Indicator Control, Fan and Peripheral-Switch Control, Embedded Control Module, Server and Networking Control.
ACPI Power-Switch Control
The PCA9539BSHP fits ACPI control boards that need multiple power-related signals without consuming a comparable number of host-controller pins. Its 16 general-purpose I/O bits operate from an I2C or SMBus connection at up to 400 kHz, while interrupt and reset functions help the host coordinate state changes. Placing the expander close to the power-switch circuitry keeps those routes short and limits the number of traces returning to the processor. Firmware can configure individual outputs for switch control, read back applicable status lines, and use the interrupt output to report events instead of continuously polling every port.
מומלץ
Industrial Sensor and Button Interface
PCA9539BSHP is useful when an industrial controller must collect several digital sensor states or user-button inputs while preserving host-processor pins for timing and communication tasks. Its 16 I/O bits provide a single logical port, and 400 kHz I2C operation supports efficient host updates. The interrupt function allows the controller to react to a changed input rather than repeatedly polling the entire port. Because the device operates from a compact HVQFN package, it can be positioned near remote connectors and front-panel switches, reducing wiring complexity while maintaining a shared serial connection to the main controller.
מומלץ
LED and Status-Indicator Control
The PCA9539BSHP can drive or monitor grouped LED and status-indicator signals through its 16 configurable I/O bits. I2C control at up to 400 kHz allows the host to update multiple indicators during a short transaction, while the interrupt path can support inputs from buttons or status switches. The 4 x 4 mm HVQFN body saves board area compared with many discrete digital-control packages. In multi-LED designs, current limiting and polarity still belong in the external circuit, and firmware should account for the electrical limits of every port before changing an input to an output.
מומלץ
Fan and Peripheral-Switch Control
PCA9539BSHP fits control boards that operate several fans, relays, or peripheral enable signals alongside a host processor. Its 16-bit parallel I/O capability groups related controls behind an I2C-bus interface, and the interrupt output can report applicable switch or fault events. Running the bus at 100 kHz or 400 kHz provides flexibility for both conventional and faster embedded control networks. Because the device is a low-power I/O expander rather than a power driver, external transistor or driver stages are required for loads whose current exceeds the device's output capability.
מומלץ
Embedded Control Module
The PCA9539BSHP is suitable for compact embedded modules that need more host-visible digital lines than the local controller can expose directly. Its 24-pin HVQFN package provides 16 I/O bits in a small footprint, while I2C or SMBus transport reduces connector and routing requirements between the host and peripheral logic. The interrupt line supports event-driven host wake-up or service routines, and reset provides a defined recovery mechanism for the port state. Firmware initialization should configure direction, masks, polarity, and the device address before external equipment is activated.
מומלץ
Server and Networking Control
PCA9539BSHP can extend a server or networking card with service LEDs, connector-present signals, reset controls, and other discrete digital functions. A 16-bit port provides a practical way to consolidate multiple low-speed signals over I2C, while 400 kHz operation supports timely updates without occupying a large number of processor pins. Interrupt and reset functions are useful when the management controller must respond to external events or restore deterministic port states. In server applications, the exact electrical limits, environmental requirements, and package layout must be reviewed against the system specification before deployment.
מומלץ
סיכום מוצרים מומלצים
נתוני עזר הנדסיים עבור PCA9539BSHP — השוואה, הנחיות תכנון ומידע על תאימות.
מדריך בחירה
השוואה עם חלופות
| פרמטר | מוצר זה | PCA9539BS |
|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors |
| Package | 24-pin HVQFN, 4 x 4 mm | 24-pin HVQFN family option; exact drawing requires confirmation |
| Number of I/O Ports | 16 bits | 16 bits |
| Bus Interface | I2C-bus and SMBus | I2C-bus and SMBus |
| Maximum I2C Clock Frequency | 400 kHz | 400 kHz |
| Supported I2C Frequencies | 100 kHz and 400 kHz | 100 kHz and 400 kHz |
| Interrupt Function | Yes | Yes |
| Reset Function | Yes | Yes |
| Device Technology | 24-pin CMOS low-power I/O expander | 24-pin CMOS low-power I/O expander |
מבדילים עיקריים
- Provides 16 configurable I/O bits behind one serial bus (לעומתPCA9539BS)
- Supports event-driven host updates through an interrupt output (לעומתPCA9539BS)
- Combines compact 4 x 4 mm HVQFN packaging with 16 I/O (לעומתPCA9539PW)
הערות תכנון
Follow the NXP HVQFN land pattern rather than approximating it from a generic QFN footprint. Connect the exposed thermal pad to the intended ground plane and add the recommended thermal-via pattern to improve heat transfer. Keep I2C traces short, route the clock and data away from high-current switching nodes, and place bus pull-up resistors where they maintain an effective resistance with the actual bus capacitance and total connected load.
Place the PCA9539BSHP near the connector, switch bank, indicator group, or other remote I/O loads that it serves. This minimizes trace lengths on the 16 parallel port lines while allowing the I2C clock, data, interrupt, and reset routes to remain compact. Provide a continuous ground reference beneath the device and isolate sensitive analog or high-speed routes from the connector-side switching currents.
Do not assume that every PCA9539-family ordering suffix has identical address behavior, package construction, or qualification. Confirm the device address, reset polarity, port default state, operating-voltage range, output-current limits, and pin assignment for the exact suffix in the NXP documentation. Firmware should also wait for a valid bus response and initialize port direction and interrupt masks before external loads begin switching.
מידע על תאימות
The verified product information identifies PCA9539BSHP as automotive, but it does not expressly state RoHS, REACH, AEC-Q100 qualification, lead-free, halogen-free, or conflict-minerals status.