Texas Instruments

PCA9554PWG4 - 8-Bit I2C I/O Expander | Texas Instruments

N.º da peça: PCA9554PWG4 ✓ Ativo
2.3 V to 5.5 V Vdss 16-TSSOP, 4.40 mm width Package 400 kHz Speed
MOQ: 1 |

PCA9554PWG4 Visão geral

The Texas Instruments PCA9554PWG4 is an 8-bit I2C/SMBus I/O expander with a 400 kHz bus interface, interrupt output, configuration registers, and 2.3 V to 5.5 V operating supply in a 16-pin TSSOP package. It adds eight configurable parallel I/O ports to a host controller while minimizing the number of pins required on the microcontroller or processor.

An I/O expander is an interface IC that extends a serial control bus into parallel digital inputs and outputs. The PCA9554 belongs to the hierarchy of I2C interface controllers, peripheral interface ICs, and general-purpose I/O expansion devices. It is useful when a system needs more GPIO pins than are available on its host controller, when inputs must be located remotely from the main processor, or when a shared two-wire bus offers a practical alternative to dedicating multiple host pins.

The PCA9554PWG4 provides eight general-purpose I/O ports, push-pull output capability, a dedicated interrupt output, and weak pull-ups. Its 2.3 V to 5.5 V supply range supports both 3 V and 5 V systems. A 400 kHz I2C interface provides a practical balance between bus speed and integration density. The manufacturer also identifies configuration registers, allowing the host to read port state, change port direction, and detect input changes through the interrupt mechanism.

Operationally, the device supports both input and output modes on the same eight-port bank. Inputs can be polled by reading the input-port register, while changes can be reported through the active-low interrupt output. The interrupt line allows the host to remain asleep or perform other work until an input event requires attention. The I2C interface includes A0, A1, and A2 address pins, allowing multiple expanders to share the same bus when the system requires additional I/O ports.

The PCA9554PWG4 is used in embedded control boards, industrial automation modules, programmable logic controllers, communication equipment, appliance controllers, test systems, and compact sensor or switch interfaces. It is especially useful when an I2C-capable microcontroller has insufficient pins for relays, indicators, buttons, selectors, or isolation-compatible digital inputs. Its small TSSOP package also supports compact board layouts where a larger parallel interface would be impractical.

For PCB design, place the bypass capacitor close to VDD and route SDA and SCL as a controlled-length bus with appropriate pull-up resistors. Confirm the logic-voltage levels of the host and all connected devices, define each port direction during startup, and account for the interrupt line when constructing the system wake-up path. The pin-description table in the manufacturer datasheet should be used when assigning tracks.

This product page combines the manufacturer overview, verified package and interface characteristics, drop-in comparison options, and practical implementation guidance for engineers evaluating an 8-bit TSSOP I/O expander.

Alternativas drop-in para PCA9554PWG4 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

Variantes desta série

Modelos da mesma série compatíveis como drop-in com PCA9554PWG4 (mesmo formato e footprint) — diferindo em Mounting Type, Package.

NXP Semiconductors
Mounting Type: Surface mount
Package: 16-pin TSSOP
Comparar com PCA9554PWG4 →

PCA9534APWR

✅ Drop-In
📦 16-TSSOP
Same 8-bit I2C expander and 16-TSSOP footprint; operating voltage and register details are 0% to 10% different based on the documented replacement relationship

📋 Alternativa de referência (fora do catálogo)

TCA9554APWR

✅ Drop-In
📦 16-TSSOP
Same 8-bit I2C/SMBus role and 16-TSSOP footprint; minimum supply voltage falls from 2.3 V to 1.65 V, a 28.3% reduction, while remaining usable within the target voltage range

📋 Alternativa de referência (fora do catálogo)

PCA9554PW

✅ Drop-In
NXP Semiconductors
📦 16-TSSOP
8-bit I2C/SMBus I/O expander with interrupt · 8 bits · 2.3 V to 5.5 V · 400 kHz · 100 kHz and 400 kHz · I2C-bus/SMBus · Yes · Input/output and polarity configuration registers

Consulte o preço

Ver ficha técnica →

PCA9554PWG4 Especificações

Number of I/O Ports 8 ports
Tipo de interface I2C/SMBus, two-line bidirectional
Maximum I2C Bus Frequency 400 kHz
Supply Voltage Range 2.3 V to 5.5 V
Tipo de saída Push-pull
Interrupt Output Yes
Configuration Registers Yes
Weak Pull-Ups Yes
Address Inputs 3 address inputs, A0 through A2
Technology CMOS
Device Type General-purpose parallel I/O expander
Faixa de temperatura de operação -40 C to +85 C
Temperature Grade Industrial
Encapsulamento 16-TSSOP, 4.40 mm width
Package Code TSSOP-16
Package Standard MO-153 / SOT403-1
Tipo de montagem Surface mount, gull wing
Number of Terminals 16 terminals

Configuração de pinos do PCA9554PWG4

TSSOP-16 Package Pinout Diagram TSSOP-16 4.4x5mm, P0.65mm, JEDEC MO-153. 1 16 2 15 3 14 4 13 5 12 6 11 7 10 8 9 TSSOP-16
Pino 1 A0 — Address input A0
Pino 2 A1 — Address input A1
Pino 3 A2 — Address input A2
Pino 4 VSS — Ground
Pino 5 P0 — General-purpose I/O port 0
Pino 6 P1 — General-purpose I/O port 1
Pino 7 P2 — General-purpose I/O port 2
Pino 8 P3 — General-purpose I/O port 3
Pino 9 VDD — Power supply
Pino 10 P4 — General-purpose I/O port 4
Pino 11 P5 — General-purpose I/O port 5
Pino 12 P6 — General-purpose I/O port 6
Pino 13 P7 — General-purpose I/O port 7
Pino 14 INT — Interrupt output
Pino 15 SCL — Serial clock
Pino 16 SDA — Serial data

Aplicações típicas

PCA9554PWG4 é adequado para 6 aplicaçãos: Industrial Automation Control, Programmable Logic Controller I/O, Communication Equipment Status Ports, Appliance and Smart-Home Interface, Test and Measurement Front Panel, Embedded Sensor and Switch Hub.

🏭

Industrial Automation Control

The PCA9554PWG4 fits industrial automation modules that need more digital control points than the host controller can expose directly. Its eight ports can operate as inputs for limit switches and status contacts or as push-pull outputs for indicators and control signals. The 2.3 V to 5.5 V supply range supports common industrial logic levels, while the 400 kHz I2C interface minimizes serial-bus occupancy. The interrupt output is valuable in machines where the controller should react promptly to a changed sensor without continuously polling eight lines. In a distributed backplane, the A0, A1, and A2 inputs allow several expanders to share the bus, reducing wiring complexity while retaining dedicated port control.

🏭

Programmable Logic Controller I/O

The PCA9554PWG4 is suitable for small PLC and relay-controller boards that combine a serial processor with a bank of field I/O. The eight parallel ports provide a compact bridge between low-voltage logic and discrete inputs or outputs, while the dedicated interrupt line can notify the processor when a field input changes. At a 400 kHz maximum I2C rate, register access is fast enough for routine button, selector, and alarm monitoring. The 16-TSSOP package also leaves more board area for power conversion and isolated interface circuitry. Designers should define startup port directions and examine whether an attached relay driver requires isolation, flyback protection, or a logic level different from the expander’s supply.

🌐

Communication Equipment Status Ports

The PCA9554PWG4 can expand status and control signals in communication equipment where the main processor manages a high-speed transceiver or network interface but lacks enough general-purpose pins. The eight ports can report link indicators, equipment-mode switches, reset requests, or alarm inputs while accepting slower configuration outputs. The 2.3 V to 5.5 V range makes the device adaptable to mixed legacy and modern logic rails, subject to proper level translation. Using the interrupt output reduces polling traffic on the host bus, and the three address inputs permit another expander to be added when a chassis requires more control lines. Keep sensitive high-speed paths physically separate and use the expander only for low-rate digital signaling.

🧩

Appliance and Smart-Home Interface

The PCA9554PWG4 is useful in appliance controllers and smart-home modules that need a small number of extra buttons, LEDs, door sensors, or configuration switches. Eight ports can be mixed as inputs and outputs, and the interrupt output lets the host wake from a low-power state when a user action occurs. Its 400 kHz I2C rate supports responsive control without tying up many processor pins. Because appliance electronics often combine mains-derived and low-voltage domains, the expander should remain on the safely regulated logic side of the design. Use appropriate protection, isolation, and pull networks for any externally accessible connector rather than routing unrestricted field wiring directly to the ports.

🔧

Test and Measurement Front Panel

The PCA9554PWG4 can add front-panel controls and indicator outputs to compact test and measurement equipment. Its eight ports are suited to rotary or push-button selections, range indicators, trigger enables, and simple status LEDs, while the interrupt output reports user activity to the main controller. The small TSSOP package preserves PCB area around connectors and analog circuitry, and the 2.3 V to 5.5 V range supports both 3.3 V and 5 V logic. A bus frequency of 400 kHz provides adequate command throughput for panel updates. For safety, ensure that controls cannot create hazardous machine states and confirm the electrical characteristics of switches, LEDs, and protection devices before connecting them to the ports.

🧩

Embedded Sensor and Switch Hub

The PCA9554PWG4 works well as a remote sensor and switch hub when sensors are distributed farther from the main controller than a conventional GPIO bus would comfortably reach. Eight digital inputs can report limit switches, door sensors, or discrete sensor outputs, while remaining ports can drive indicators. The interrupt line provides an efficient wake-up mechanism, and address selection permits multiple hubs on the same two-wire bus. The 2.3 V to 5.5 V operating range supports common embedded rails, but long external wiring requires protection against transients and ground offsets. Use short, controlled interconnects or an appropriate differential interface when the installation distance introduces unacceptable noise or common-mode voltage.

What is the PCA9554PWG4 and what does it do?
The PCA9554PWG4 is an 8-bit I2C/SMBus I/O expander that adds eight configurable parallel ports to a host controller. According to the Texas Instruments product page, it operates from 2.3 V to 5.5 V, supports a 400 kHz bus, includes an interrupt output, and provides weak pull-ups and configuration registers. It is useful when a microcontroller has too few GPIO pins for buttons, indicators, relays, or other digital signals.
What are the key specifications of PCA9554PWG4 that engineers should know?
The PCA9554PWG4 provides 8 general-purpose I/O ports, a 2.3 V to 5.5 V operating range, and a 400 kHz I2C/SMBus interface. The Texas Instruments product page also identifies an interrupt output, push-pull port operation, weak pull-ups, configuration registers, and three address inputs. The device is packaged in a 16-pin TSSOP with an industrial temperature rating of -40 C to +85 C.
Where can I download the PCA9554PWG4 datasheet PDF?
The official PCA9554PWG4 technical information is available through the Texas Instruments PCA9554 product page, which links to the manufacturer datasheet and ordering information. The device is described there as an 8-bit, 2.3 V to 5.5 V I2C/SMBus I/O expander with interrupt, weak pull-up, and configuration-register functions. Use the manufacturer document for the authoritative pin description, register map, electrical characteristics, and application guidance.
Where can I find the PCA9554PWG4 pinout?
The PCA9554PWG4 pinout is identified in the manufacturer datasheet, where the 16 TSSOP terminals include the three address inputs, ground, eight I/O ports, supply, interrupt, clock, and data pins. For PCB work, use the datasheet pin-description table and package drawing when assigning tracks. The verified package is 16-TSSOP in the 4.40 mm-wide MO-153 or SOT403-1 outline.
How does the PCA9554PWG4 interrupt output work?
The PCA9554PWG4 provides a dedicated interrupt output so the host can respond to a port-input change without continuously polling all eight ports. According to the Texas Instruments product page, interrupt support is one of the device’s principal functions. The host must configure the relevant port directions and masks through the device registers, then service the interrupt by reading the appropriate port or interrupt-status information.
Can multiple PCA9554 devices share one I2C bus?
Yes, multiple PCA9554 devices can share the same I2C bus by assigning different addresses with the A0, A1, and A2 inputs. The PCA9554PWG4 provides three hardware-address inputs and a maximum bus frequency of 400 kHz. Each device still requires adequate input decoupling, while the shared SDA and SCL lines require pull-up resistors selected for the complete bus capacitance and operating voltage.
Is PCA9554PWG4 suitable for 3.3 V and 5 V systems?
The PCA9554PWG4 is suitable for both 3.3 V and 5 V systems because its specified operating supply range is 2.3 V to 5.5 V. According to the Texas Instruments product overview, it is an 8-bit I2C/SMBus I/O expander for general-purpose remote I/O expansion. The host, pull-up network, external loads, and attached peripherals must all use compatible logic levels.
Where can I buy PCA9554PWG4 and check current availability?
Use the Request a Quote form on this page to ask about PCA9554PWG4 availability, order quantity, and lead time. The verified manufacturer and distributor listings identify the part as a Texas Instruments 16-TSSOP I/O expander, but current commercial terms can change independently of technical lifecycle status. A quotation request provides the most direct way to confirm stock, schedule, and quantity handling for your specific order.
What is the price of PCA9554PWG4?
The current commercial terms for PCA9554PWG4 are shown through the Request a Quote form on this page. Submit the required quantity and target package or delivery details to receive an offer. The price should not be inferred from a historical catalog amount because distributor inventories, production volume, and quotation terms can change over time.
What is the lead time for PCA9554PWG4?
The current lead time for PCA9554PWG4 should be confirmed through the Request a Quote form on this page. Lead time can depend on available inventory, requested quantity, manufacturing status, and delivery location. The manufacturer product page identifies the PCA9554 family, while the verified distributor listing shows the exact 16-TSSOP orderable MPN; neither listing should be treated as a guaranteed current delivery commitment.
Is PCA9554PWG4 in stock?
Current PCA9554PWG4 stock should be checked through the Request a Quote form on this page. The device is listed by the manufacturer and appears in distributor catalogs, but a listing does not by itself guarantee a specific quantity or delivery date. Include your required quantity, package preference, and destination so the supplier can confirm an available allocation.
What is the difference between PCA9554PWG4 and PCA9554PW?
Both devices are associated with the PCA9554 8-bit I2C/SMBus I/O-expander function and a 16-pin TSSOP-class package, but MPN suffixes can identify different manufacturers, qualification details, or packaging configurations. The PCA9554PWG4 is the Texas Instruments orderable part identified in the verified listings, while PCA9554PW appears in cross-reference results as another supplier’s related ordering code. Confirm manufacturer, register behavior, address options, and package drawing before substitution.
Can TCA9554APWR replace PCA9554PWG4?
TCA9554APWR is a strong functional candidate because it is an 8-bit I2C/SMBus I/O expander in a 16-pin TSSOP package, according to the supplied comparison result. Its listed operating range of 1.65 V to 5.5 V overlaps the PCA9554PWG4’s 2.3 V to 5.5 V range. Pin compatibility still requires checking the address inputs, interrupt polarity, reset or power-on behavior, output defaults, and selected-device address against the target schematic.
When should I choose PCA9554PWG4 instead of a direct 8-bit expander alternative?
Choose PCA9554PWG4 when the design specifically targets the Texas Instruments PCA9554, needs its 2.3 V to 5.5 V operating range, and has an established TSSOP-16 footprint and interrupt architecture. Consider PCA9534APWR when its register or addressing behavior matches the application exactly, and evaluate TCA9554APWR when its lower minimum supply voltage or device-specific behavior provides a useful advantage. Verify every register and electrical difference before approving a replacement.
What is the best drop-in replacement for PCA9554PWG4?
The best drop-in replacement is the candidate that matches the PCA9554PWG4’s 16-pin TSSOP footprint, 8-bit port count, I2C addressing, interrupt polarity, and power-on defaults. PCA9534APWR and TCA9554APWR are documented comparison candidates, while PCA9554PW is a related cross-reference entry. None should be treated as automatically interchangeable without checking the manufacturer datasheet and schematic-level behavior differences.
What can replace PCA9554PWG4 in an embedded control board?
A suitable replacement must provide eight I/O ports in the same TSSOP-16 footprint and preserve the target board’s I2C address and interrupt wiring. PCA9534APWR is identified in the supplied comparison material as a complete replacement candidate, while TCA9554APWR offers the same general 8-bit I2C/SMBus function. Because power-on defaults and register details can affect production boards, verify the complete operating behavior rather than relying only on package and port count.
How should PCA9554PWG4 be used with a 3.3 V microcontroller?
Power the PCA9554PWG4 from a compatible 3.3 V rail within its 2.3 V to 5.5 V operating range and connect its I2C interface to matching 3.3 V logic. According to the Texas Instruments product page, the device supports 400 kHz operation and includes three address inputs. Place the required bypass capacitor near VDD, use pull-ups connected to the logic rail, and ensure attached outputs and inputs do not exceed the port electrical limits.

Dados de referência de engenharia para PCA9554PWG4 — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose PCA9554PWG4 when the design is standardized around the Texas Instruments PCA9554 family, uses a 2.3 V to 5.5 V logic rail, and needs eight I/O ports with interrupt support in a 16-TSSOP footprint. Its three address inputs are useful for systems with multiple expanders, while the 400 kHz interface keeps bus traffic efficient. Consider PCA9534APWR when its documented replacement relationship covers the required register and addressing behavior and it offers a preferred sourcing route. Evaluate TCA9554APWR when operation below 2.3 V or its specific device behavior provides a clear advantage. PCA9554PW may suit cross-procurement strategies, but manufacturer-specific ordering, qualification, and register details must be reviewed. For every candidate, verify footprint dimensions, address pins, interrupt polarity, port defaults, logic thresholds, and firmware register compatibility before release.

Comparação com alternativas

Parâmetro Este produto PCA9534APWR TCA9554APWR PCA9554PW
Brand Texas Instruments Texas Instruments Texas Instruments NXP Semiconductors
Package 16-TSSOP 16-TSSOP - same footprint class 16-TSSOP - same footprint class 16-TSSOP - same footprint class
I/O Port Count 8 8 8 8
Interface I2C/SMBus I2C/SMBus I2C/SMBus I2C/SMBus
Interrupt Output Yes Yes Yes Yes
Configuration Registers Yes Yes Yes Yes

Principais diferenciais

  • Maintains the established Texas Instruments PCA9554 function and address organization (vs PCA9534APWR)
  • Targets a broad 2.3 V to 5.5 V operating range (vs TCA9554APWR)
  • Provides three hardware address inputs for multi-expander buses (vs PCA9554PW)

Notas de projeto

Place the PCA9554PWG4 close to the connector or controlled signal group it serves. Route the eight port traces away from switching nodes and analog inputs, use a ground plane for return current, and keep SDA and SCL away from high-current edges. Connect the device VDD pin to a quiet local rail through a short path, and place the required bypass capacitor immediately beside VDD and VSS. The manufacturer pin-description table should be followed when assigning the TSSOP-16 footprint.

Treat SDA and SCL as a shared bus with one pull-up resistor per line, not one resistor at every connected device. Select pull-up values from the bus capacitance, operating voltage, and sink-current limits rather than using a universally fixed value. The PCA9554PWG4 supports up to 400 kHz, but long branches, excessive loading, or slow edge rates can still create timing errors. Test the completed board at the intended bus rate and account for temperature and process variation.

Do not assume that identical packages imply identical behavior. Before substituting another 16-TSSOP expander, compare the A0, A1, and A2 address mapping, port polarity, power-on defaults, interrupt polarity, input thresholds, and register access sequence. Also verify whether the replacement changes the minimum operating voltage. A pin-compatible part can still require firmware changes if its command set, output states, or interrupt event behavior differs.

Check every attached load against the port current and logic-level limits before enabling a port as an output. A low-voltage expander may not directly drive a relay, high-current LED, or long external line even though its output is described as push-pull. Use suitable drivers, transistors, isolation, and flyback protection where required. Because port behavior during power-up matters in systems with external connectors, establish safe default states in the host startup sequence and design external hardware so an inactive or high-impedance state cannot create a hazard.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The verified manufacturer overview identifies the PCA9554 as an industrial-temperature I/O expander but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a general-purpose interface IC rather than an automotive-qualified device.

Buscas relacionadas

PCA9554PWG4 PCA9554PWG4 datasheet PCA9554PWG4 datasheet pdf PCA9554PWG4 pinout PCA9554PWG4 equivalent PCA9554PWG4 replacement PCA9554PWG4 cross reference PCA9554PWG4 price PCA9554PWG4 stock Texas Instruments PCA9554PWG4 PCA9554PWG4 TSSOP-16 footprint PCA9554PWG4 400 kHz I2C PCA9554PWG4 8-bit I/O expander PCA9554PWG4 vs TCA9554APWR PCA9554PWG4 industrial control application

Componentes & termos relacionados

Texas Instruments PCA9554PWG4 PCA9554 PCA9534APWR TCA9554APWR PCA9554PW NXP Semiconductors I/O expander parallel I/O interface IC I2C SMBus general-purpose I/O interrupt output configuration register weak pull-up CMOS 16-TSSOP TSSOP family surface mount SMD 2.3 V to 5.5 V 400 kHz industrial automation embedded control
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ