PCA9554PWG4 - 8-Bit I2C I/O Expander | Texas Instruments
MPN: PCA9554PWG4 ✓ فعالPCA9554PWG4 جائزہ
An I/O expander is an interface IC that extends a serial control bus into parallel digital inputs and outputs. The PCA9554 belongs to the hierarchy of I2C interface controllers, peripheral interface ICs, and general-purpose I/O expansion devices. It is useful when a system needs more GPIO pins than are available on its host controller, when inputs must be located remotely from the main processor, or when a shared two-wire bus offers a practical alternative to dedicating multiple host pins.
The PCA9554PWG4 provides eight general-purpose I/O ports, push-pull output capability, a dedicated interrupt output, and weak pull-ups. Its 2.3 V to 5.5 V supply range supports both 3 V and 5 V systems. A 400 kHz I2C interface provides a practical balance between bus speed and integration density. The manufacturer also identifies configuration registers, allowing the host to read port state, change port direction, and detect input changes through the interrupt mechanism.
Operationally, the device supports both input and output modes on the same eight-port bank. Inputs can be polled by reading the input-port register, while changes can be reported through the active-low interrupt output. The interrupt line allows the host to remain asleep or perform other work until an input event requires attention. The I2C interface includes A0, A1, and A2 address pins, allowing multiple expanders to share the same bus when the system requires additional I/O ports.
The PCA9554PWG4 is used in embedded control boards, industrial automation modules, programmable logic controllers, communication equipment, appliance controllers, test systems, and compact sensor or switch interfaces. It is especially useful when an I2C-capable microcontroller has insufficient pins for relays, indicators, buttons, selectors, or isolation-compatible digital inputs. Its small TSSOP package also supports compact board layouts where a larger parallel interface would be impractical.
For PCB design, place the bypass capacitor close to VDD and route SDA and SCL as a controlled-length bus with appropriate pull-up resistors. Confirm the logic-voltage levels of the host and all connected devices, define each port direction during startup, and account for the interrupt line when constructing the system wake-up path. The pin-description table in the manufacturer datasheet should be used when assigning tracks.
This product page combines the manufacturer overview, verified package and interface characteristics, drop-in comparison options, and practical implementation guidance for engineers evaluating an 8-bit TSSOP I/O expander.
کے لیے ڈراپ اِن متبادل PCA9554PWG4 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں PCA9554PWG4 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Mounting Type, Package.
PCA9534APWR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TCA9554APWR
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
PCA9554PW
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →PCA9554PWG4 تفصیلات
| Number of I/O Ports | 8 ports |
| انٹرفیس ٹائپ | I2C/SMBus, two-line bidirectional |
| Maximum I2C Bus Frequency | 400 kHz |
| Supply Voltage Range | 2.3 V to 5.5 V |
| آؤٹ پٹ کی قسم | Push-pull |
| Interrupt Output | Yes |
| Configuration Registers | Yes |
| Weak Pull-Ups | Yes |
| Address Inputs | 3 address inputs, A0 through A2 |
| Technology | CMOS |
| Device Type | General-purpose parallel I/O expander |
| آپریٹنگ درجہ حرارت رینج | -40 C to +85 C |
| Temperature Grade | Industrial |
| پیکیج | 16-TSSOP, 4.40 mm width |
| Package Code | TSSOP-16 |
| Package Standard | MO-153 / SOT403-1 |
| ماؤنٹنگ ٹائپ | Surface mount, gull wing |
| Number of Terminals | 16 terminals |
PCA9554PWG4 پن کنفیگریشن
| پن 1 | A0 — Address input A0 |
| پن 2 | A1 — Address input A1 |
| پن 3 | A2 — Address input A2 |
| پن 4 | VSS — Ground |
| پن 5 | P0 — General-purpose I/O port 0 |
| پن 6 | P1 — General-purpose I/O port 1 |
| پن 7 | P2 — General-purpose I/O port 2 |
| پن 8 | P3 — General-purpose I/O port 3 |
| پن 9 | VDD — Power supply |
| پن 10 | P4 — General-purpose I/O port 4 |
| پن 11 | P5 — General-purpose I/O port 5 |
| پن 12 | P6 — General-purpose I/O port 6 |
| پن 13 | P7 — General-purpose I/O port 7 |
| پن 14 | INT — Interrupt output |
| پن 15 | SCL — Serial clock |
| پن 16 | SDA — Serial data |
عام استعمالات
PCA9554PWG4 کے لیے موزوں ہے 6 ایپلیکیشنs: Industrial Automation Control, Programmable Logic Controller I/O, Communication Equipment Status Ports, Appliance and Smart-Home Interface, Test and Measurement Front Panel, Embedded Sensor and Switch Hub.
Industrial Automation Control
The PCA9554PWG4 fits industrial automation modules that need more digital control points than the host controller can expose directly. Its eight ports can operate as inputs for limit switches and status contacts or as push-pull outputs for indicators and control signals. The 2.3 V to 5.5 V supply range supports common industrial logic levels, while the 400 kHz I2C interface minimizes serial-bus occupancy. The interrupt output is valuable in machines where the controller should react promptly to a changed sensor without continuously polling eight lines. In a distributed backplane, the A0, A1, and A2 inputs allow several expanders to share the bus, reducing wiring complexity while retaining dedicated port control.
تجویز کردہ
Programmable Logic Controller I/O
The PCA9554PWG4 is suitable for small PLC and relay-controller boards that combine a serial processor with a bank of field I/O. The eight parallel ports provide a compact bridge between low-voltage logic and discrete inputs or outputs, while the dedicated interrupt line can notify the processor when a field input changes. At a 400 kHz maximum I2C rate, register access is fast enough for routine button, selector, and alarm monitoring. The 16-TSSOP package also leaves more board area for power conversion and isolated interface circuitry. Designers should define startup port directions and examine whether an attached relay driver requires isolation, flyback protection, or a logic level different from the expander’s supply.
تجویز کردہ
Communication Equipment Status Ports
The PCA9554PWG4 can expand status and control signals in communication equipment where the main processor manages a high-speed transceiver or network interface but lacks enough general-purpose pins. The eight ports can report link indicators, equipment-mode switches, reset requests, or alarm inputs while accepting slower configuration outputs. The 2.3 V to 5.5 V range makes the device adaptable to mixed legacy and modern logic rails, subject to proper level translation. Using the interrupt output reduces polling traffic on the host bus, and the three address inputs permit another expander to be added when a chassis requires more control lines. Keep sensitive high-speed paths physically separate and use the expander only for low-rate digital signaling.
تجویز کردہ
Appliance and Smart-Home Interface
The PCA9554PWG4 is useful in appliance controllers and smart-home modules that need a small number of extra buttons, LEDs, door sensors, or configuration switches. Eight ports can be mixed as inputs and outputs, and the interrupt output lets the host wake from a low-power state when a user action occurs. Its 400 kHz I2C rate supports responsive control without tying up many processor pins. Because appliance electronics often combine mains-derived and low-voltage domains, the expander should remain on the safely regulated logic side of the design. Use appropriate protection, isolation, and pull networks for any externally accessible connector rather than routing unrestricted field wiring directly to the ports.
تجویز کردہ
Test and Measurement Front Panel
The PCA9554PWG4 can add front-panel controls and indicator outputs to compact test and measurement equipment. Its eight ports are suited to rotary or push-button selections, range indicators, trigger enables, and simple status LEDs, while the interrupt output reports user activity to the main controller. The small TSSOP package preserves PCB area around connectors and analog circuitry, and the 2.3 V to 5.5 V range supports both 3.3 V and 5 V logic. A bus frequency of 400 kHz provides adequate command throughput for panel updates. For safety, ensure that controls cannot create hazardous machine states and confirm the electrical characteristics of switches, LEDs, and protection devices before connecting them to the ports.
تجویز کردہ
Embedded Sensor and Switch Hub
The PCA9554PWG4 works well as a remote sensor and switch hub when sensors are distributed farther from the main controller than a conventional GPIO bus would comfortably reach. Eight digital inputs can report limit switches, door sensors, or discrete sensor outputs, while remaining ports can drive indicators. The interrupt line provides an efficient wake-up mechanism, and address selection permits multiple hubs on the same two-wire bus. The 2.3 V to 5.5 V operating range supports common embedded rails, but long external wiring requires protection against transients and ground offsets. Use short, controlled interconnects or an appropriate differential interface when the installation distance introduces unacceptable noise or common-mode voltage.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا PCA9554PWG4 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | PCA9534APWR | TCA9554APWR | PCA9554PW |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | NXP Semiconductors |
| Package | 16-TSSOP | 16-TSSOP - same footprint class | 16-TSSOP - same footprint class | 16-TSSOP - same footprint class |
| I/O Port Count | 8 | 8 | 8 | 8 |
| Interface | I2C/SMBus | I2C/SMBus | I2C/SMBus | I2C/SMBus |
| Interrupt Output | Yes | Yes | Yes | Yes |
| Configuration Registers | Yes | Yes | Yes | Yes |
اہم امتیازی خصوصیات
- Maintains the established Texas Instruments PCA9554 function and address organization (بمقابلہPCA9534APWR)
- Targets a broad 2.3 V to 5.5 V operating range (بمقابلہTCA9554APWR)
- Provides three hardware address inputs for multi-expander buses (بمقابلہPCA9554PW)
ڈیزائن نوٹس
Place the PCA9554PWG4 close to the connector or controlled signal group it serves. Route the eight port traces away from switching nodes and analog inputs, use a ground plane for return current, and keep SDA and SCL away from high-current edges. Connect the device VDD pin to a quiet local rail through a short path, and place the required bypass capacitor immediately beside VDD and VSS. The manufacturer pin-description table should be followed when assigning the TSSOP-16 footprint.
Treat SDA and SCL as a shared bus with one pull-up resistor per line, not one resistor at every connected device. Select pull-up values from the bus capacitance, operating voltage, and sink-current limits rather than using a universally fixed value. The PCA9554PWG4 supports up to 400 kHz, but long branches, excessive loading, or slow edge rates can still create timing errors. Test the completed board at the intended bus rate and account for temperature and process variation.
Do not assume that identical packages imply identical behavior. Before substituting another 16-TSSOP expander, compare the A0, A1, and A2 address mapping, port polarity, power-on defaults, interrupt polarity, input thresholds, and register access sequence. Also verify whether the replacement changes the minimum operating voltage. A pin-compatible part can still require firmware changes if its command set, output states, or interrupt event behavior differs.
Check every attached load against the port current and logic-level limits before enabling a port as an output. A low-voltage expander may not directly drive a relay, high-current LED, or long external line even though its output is described as push-pull. Use suitable drivers, transistors, isolation, and flyback protection where required. Because port behavior during power-up matters in systems with external connectors, establish safe default states in the host startup sequence and design external hardware so an inactive or high-impedance state cannot create a hazard.
تعمیل کی معلومات
The verified manufacturer overview identifies the PCA9554 as an industrial-temperature I/O expander but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status. AEC-Q100 is not applicable because this is a general-purpose interface IC rather than an automotive-qualified device.