PCA9673D - 16-Bit I2C GPIO Expander | NXP Semiconductors
N.º da peça: PCA9673D ✓ AtivoPCA9673D Visão geral
An I/O expander is a peripheral interface IC that increases the number of general-purpose input or output lines available to a host processor. It sits within the embedded-control hierarchy as an I2C peripheral, allowing a microcontroller or application processor to control or monitor external signals over the two-wire bus instead of requiring one host GPIO for every external line. The PCA9673D therefore belongs to the interface IC family rather than the microcontroller or GPIO-controller families.
Its principal features include 16 remotely controlled I/O lines, a 1 MHz I2C clock rate, compatibility with Fast-mode Plus operation, and dedicated interrupt and reset functions. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V system environments when the host, pull-up network, and external loads are designed for the corresponding voltage. The 24-pin SOIC format supports conventional surface-mount assembly and PCB routing.
The PCA9673D is intended for systems in which a controller needs additional digital interface points. I2C address control, register-based configuration, and the interrupt output can reduce direct host-controller pin usage while providing a structured way to monitor external events. Because bus capacitance, pull-up resistance, voltage levels, and output timing influence reliable operation, the device should be used with a power supply and I2C network that remain within the manufacturer's stated limits.
Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, test equipment, and compact embedded products that need more digital lines than the host controller provides. Its interrupt function is especially useful when an external change must wake or notify the host, while the reset function supports coordinated initialization of the expansion interface and attached circuitry.
PCB layout should keep the I2C wiring short and route the SCL and SDA nets away from high-current switching edges. Confirm pull-up values for the intended bus voltage and frequency, provide suitable decoupling at the supply pins, and review the 24-pin pin-description table in the manufacturer datasheet before assigning every signal. The package drawing and pin names should be checked against the selected assembly footprint.
This page consolidates the verified device specifications, ordering information, package details, replacement constraints, and practical implementation guidance into a design-oriented resource. It also distinguishes the documented PCA9673D configuration from order-code variants and explains which compatibility claims must be confirmed at the pin, voltage, and timing level before substitution.
Alternativas drop-in para PCA9673D — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
PCA9673D,118
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCA9673D,112
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PCA9673D Especificações
| Device Type | Remote 16-bit I/O expander |
| Number of I/O Lines | 16 lines |
| Host Interface | I2C two-wire bidirectional bus |
| I2C Mode | Fast-mode Plus |
| Maximum I2C Clock Frequency | 1 MHz |
| Supply Voltage Range | 2.3 V to 5.5 V |
| Número de pinos | 24 pins |
| Encapsulamento | 24-SOIC, 0.295 inch body width, 7.50 mm width |
| Interrupt Function | Supported |
| Reset Function | Supported |
| Tipo de montagem | Surface mount |
Guia de Configuração de Pinos do PCA9673D 24-soic, 0.295 inch body width, 7.50 mm width
Configuração de pinos para PCA9673D (pacote 24-soic, 0.295 inch body width, 7.50 mm width). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para PCA9673D.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PCA9673D é adequado para 6 aplicaçãos: Industrial Control and Relay Interface, Sensor Hub and Condition Monitoring, Programmable Logic Controller Expansion, Test and Measurement Equipment, LED and Display Control Interface, Secure and Surveillance Peripheral Interface.
Industrial Control and Relay Interface
The PCA9673D fits industrial control assemblies that need numerous low-rate digital command or status signals without consuming every GPIO on the host controller. Its 16 I/O lines can connect to relay-control logic, status indicators, mode selectors, and discrete sensor interfaces, while the 1 MHz Fast-mode Plus I2C link updates those functions efficiently. The device also provides reset and interrupt functions for coordinated initialization and event notification. Designers should partition the 16 lines according to output-drive and input-voltage requirements, use a common ground between the controller and interface board, and select pull-ups for the actual bus voltage. The 24-SOIC package simplifies conventional surface-mount assembly but requires attention to the 7.50 mm body-width footprint.
Recomendado
Sensor Hub and Condition Monitoring
The PCA9673D is useful in sensor-hub and condition-monitoring equipment where multiple digital thresholds, alarm inputs, and configuration signals must be connected to a microcontroller over a shared bus. The documented 16-line capacity allows one device to consolidate discrete I/O, and the 1 MHz I2C rate supports timely register access when several sensors and actuators share the bus. An interrupt output can notify the host when a monitored condition changes, reducing the need for continuous status polling. The supply range of 2.3 V to 5.5 V supports low-voltage and legacy 5 V sensor arrangements, but each attached circuit must remain within that range. Pull-up selection, bus capacitance, isolation boundaries, and grounding should be reviewed before connecting long sensor cables.
Recomendado
Programmable Logic Controller Expansion
The PCA9673D can expand a programmable logic controller or embedded automation controller when the base module has too few direct digital lines. Its remote 16-bit I/O capability is appropriate for connecting pushbuttons, mode controls, lamps, interlock signals, and discrete outputs while preserving a compact module footprint. Fast-mode Plus operation at up to 1 MHz provides useful bandwidth, although actual update rate depends on bus loading and the number of devices sharing the bus. The interrupt function supports change-driven control loops, while reset helps establish a known state during startup. Engineers should define each line as input or output only after checking the detailed configuration registers, and they should avoid driving outputs before the external circuit is initialized.
Recomendado
Test and Measurement Equipment
The PCA9673D is appropriate for test equipment that needs a deterministic register interface to front-panel controls, fixture selectors, relay drivers, and capture indicators. Consolidating these lines over I2C can reduce wiring between a controller board and an instrument interface, while the 1 MHz Fast-mode Plus capability supports reasonably rapid configuration updates. The reset function provides a practical mechanism for restoring the expansion interface when a test sequence begins, and the interrupt output can report asynchronous fixture or operator events. Supply sequencing and signal levels should be coordinated with the test system so that external loads remain off during reset. The 24-SOIC package requires a conventional SOIC land pattern and adequate clearance around neighboring components.
Recomendado
LED and Display Control Interface
The PCA9673D can serve as the remote digital interface between a controller and grouped display or LED-driver boards. Instead of connecting every enable, mode, or segment-control signal directly to a microcontroller, the 16 lines can be managed through the I2C register interface at up to 1 MHz. This arrangement is especially useful in compact panels where connector pins and board area are constrained. Interrupt handling can report button or panel events, and reset can help coordinate panel initialization. The 2.3 V to 5.5 V device range supports both common logic levels, but the selected LED drivers, level shifters, and pull-ups must match the panel's voltage and current requirements. Confirm output timing and drive limits in the detailed electrical tables before connecting high-current loads directly.
Recomendado
Secure and Surveillance Peripheral Interface
The PCA9673D can extend a surveillance or access-control controller with digital lines for door contacts, request-to-exit buttons, alarm inputs, indicator outputs, and other peripheral signals. Remote I/O reduces the number of direct host GPIO connections and helps organize a multi-board installation around I2C. The interrupt output can alert the controller to a change on an external line, while reset supports controlled startup of the peripheral interface. Security equipment may use longer cable runs and electrically noisy relays, so designers should incorporate appropriate protection and isolation without exceeding the 2.3 V to 5.5 V supply limits. Bus pull-ups, grounding, shielding, and the location of the interrupt trace should be evaluated for the final mechanical and wiring environment.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PCA9673D — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PCA9673D,118 | PCA9673D,112 |
|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 24-SOIC | 24-SOIC | 24-SOIC |
| Number of I/O Lines | 16 lines | 16 lines | 16 lines |
| Host Interface | I2C | I2C | I2C |
| Maximum Clock Frequency | 1 MHz | 1 MHz | 1 MHz |
| Supply Voltage Range | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V |
| I2C Mode | Fast-mode Plus | Fast-mode Plus | Fast-mode Plus |
| Interrupt and Reset | Supported | Supported | Supported |
| Ordering and Shipment Presentation | Base PCA9673D designation | ,118 ordering code associated with cut tape | ,112 ordering code with 24-SO listing |
Principais diferenciais
- Provides 16 remote digital lines through a single I2C peripheral (vs PCA9673D,118)
- Supports Fast-mode Plus operation across a broad supply range (vs PCA9673D,112)
- Combines interrupt and reset functions in the remote I/O interface (vs PCA9673D,118)
Notas de projeto
Route SCL and SDA as short, continuous traces between the host controller and PCA9673D, and place the pull-up network near the bus master according to the system topology. Avoid stubs, test pads that add unnecessary capacitance, and routing through switching-power regions. Confirm the actual board-level capacitance against the Fast-mode Plus timing budget before operating the bus at the documented 1 MHz maximum.
Design the 2.3 V to 5.5 V supply rail to remain within the PCA9673D operating range under startup, reset, and load transients. Place local decoupling close to the supply and ground pins, with a short return path to the ground reference. If the expander controls relays, LEDs, or other switching loads, separate their supply paths from the I2C and logic rails to prevent transient coupling.
Do not assign PCB nets solely from the device ordering code. Confirm the 24-SOIC footprint, pin-one orientation, individual pin names, input or output direction, and active levels using the manufacturer pin-description and pinout tables. A base MPN, a cut-tape suffix, and a shipment-code suffix can describe the same electrical device while carrying different assembly or ordering requirements.
Review rise-time and fall-time behavior at the intended bus frequency rather than treating 1 MHz as a guaranteed system operating point. Pull-up strength affects rise time, while excessive capacitance slows transitions. Place the PCA9673D close enough to the host for a clean segment, use a continuous ground reference, and avoid crossing the I2C pair with noisy power or relay-routing boundaries.
Informações de conformidade
No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement is included in the retrieved device information. AEC-Q100 is marked not applicable because this catalog device is not identified as an automotive-qualified variant.