NXP Semiconductors

PCA9673D - 16-Bit I2C GPIO Expander | NXP Semiconductors

부품 번호: PCA9673D ✓ 활성
2.3 V to 5.5 V Vdss 24-SOIC, 0.295 inch body width, 7.50 mm width Package 1 MHz Speed
MOQ: 1 |

PCA9673D 개요

The NXP Semiconductors PCA9673D is a remote 16-bit I/O expander for Fast-mode Plus I2C communication, operating at a maximum clock frequency of 1 MHz across a 2.3 V to 5.5 V supply range. The device is offered in a 24-pin SOIC package and provides interrupt and reset functions for connected microcontroller systems.

An I/O expander is a peripheral interface IC that increases the number of general-purpose input or output lines available to a host processor. It sits within the embedded-control hierarchy as an I2C peripheral, allowing a microcontroller or application processor to control or monitor external signals over the two-wire bus instead of requiring one host GPIO for every external line. The PCA9673D therefore belongs to the interface IC family rather than the microcontroller or GPIO-controller families.

Its principal features include 16 remotely controlled I/O lines, a 1 MHz I2C clock rate, compatibility with Fast-mode Plus operation, and dedicated interrupt and reset functions. The 2.3 V to 5.5 V operating range supports both 3.3 V and 5 V system environments when the host, pull-up network, and external loads are designed for the corresponding voltage. The 24-pin SOIC format supports conventional surface-mount assembly and PCB routing.

The PCA9673D is intended for systems in which a controller needs additional digital interface points. I2C address control, register-based configuration, and the interrupt output can reduce direct host-controller pin usage while providing a structured way to monitor external events. Because bus capacitance, pull-up resistance, voltage levels, and output timing influence reliable operation, the device should be used with a power supply and I2C network that remain within the manufacturer's stated limits.

Typical uses include industrial control modules, sensor-hub boards, programmable logic controllers, test equipment, and compact embedded products that need more digital lines than the host controller provides. Its interrupt function is especially useful when an external change must wake or notify the host, while the reset function supports coordinated initialization of the expansion interface and attached circuitry.

PCB layout should keep the I2C wiring short and route the SCL and SDA nets away from high-current switching edges. Confirm pull-up values for the intended bus voltage and frequency, provide suitable decoupling at the supply pins, and review the 24-pin pin-description table in the manufacturer datasheet before assigning every signal. The package drawing and pin names should be checked against the selected assembly footprint.

This page consolidates the verified device specifications, ordering information, package details, replacement constraints, and practical implementation guidance into a design-oriented resource. It also distinguishes the documented PCA9673D configuration from order-code variants and explains which compatibility claims must be confirmed at the pin, voltage, and timing level before substitution.

드롭인 대체품: PCA9673D — 동일 패키지, 핀 호환. PCB 재작업이 필요한 다른 패키지 부품은 제외됩니다.

PCA9673D,118

✅ 드롭인
📦 24-SOIC
Same 16-bit I/O and 1 MHz I2C ratings; ordered suffix identifies the cut-tape shipment configuration rather than a different circuit function

📋 참조 대체품 (카탈로그에 없음)

PCA9673D,112

✅ 드롭인
📦 24-SOIC
Same 16-bit I/O and 1 MHz I2C ratings; ordering suffix differs in shipment presentation while the listed device remains 24-SO

📋 참조 대체품 (카탈로그에 없음)

PCA9673D 사양

Device Type Remote 16-bit I/O expander
Number of I/O Lines 16 lines
Host Interface I2C two-wire bidirectional bus
I2C Mode Fast-mode Plus
Maximum I2C Clock Frequency 1 MHz
Supply Voltage Range 2.3 V to 5.5 V
핀 수 24 pins
패키지 24-SOIC, 0.295 inch body width, 7.50 mm width
Interrupt Function Supported
Reset Function Supported
실장 유형 Surface mount

PCA9673D 24-soic, 0.295 inch body width, 7.50 mm width 핀 구성 가이드

PCA9673D(24-soic, 0.295 inch body width, 7.50 mm width 패키지)의 핀 구성입니다. 핀 번호, 기능, 연결 다이어그램은 제조사 데이터시트에 정의되어 있습니다. 정확한 풋프린트와 솔더링 지침은 해당 문서를 참조하십시오.

PCA9673D의 24-soic, 0.295 inch body width, 7.50 mm width 패키지 핀아웃 다이어그램

다음에 대한 상세 핀아웃 데이터 없음: PCA9673D.

다음을 참조하십시오: 데이터시트 전체 핀 구성은 다음을 참조하십시오.

일반적인 애플리케이션

PCA9673D 적합 용도: 6 애플리케이션s: Industrial Control and Relay Interface, Sensor Hub and Condition Monitoring, Programmable Logic Controller Expansion, Test and Measurement Equipment, LED and Display Control Interface, Secure and Surveillance Peripheral Interface.

🏭

Industrial Control and Relay Interface

The PCA9673D fits industrial control assemblies that need numerous low-rate digital command or status signals without consuming every GPIO on the host controller. Its 16 I/O lines can connect to relay-control logic, status indicators, mode selectors, and discrete sensor interfaces, while the 1 MHz Fast-mode Plus I2C link updates those functions efficiently. The device also provides reset and interrupt functions for coordinated initialization and event notification. Designers should partition the 16 lines according to output-drive and input-voltage requirements, use a common ground between the controller and interface board, and select pull-ups for the actual bus voltage. The 24-SOIC package simplifies conventional surface-mount assembly but requires attention to the 7.50 mm body-width footprint.

🧩

Sensor Hub and Condition Monitoring

The PCA9673D is useful in sensor-hub and condition-monitoring equipment where multiple digital thresholds, alarm inputs, and configuration signals must be connected to a microcontroller over a shared bus. The documented 16-line capacity allows one device to consolidate discrete I/O, and the 1 MHz I2C rate supports timely register access when several sensors and actuators share the bus. An interrupt output can notify the host when a monitored condition changes, reducing the need for continuous status polling. The supply range of 2.3 V to 5.5 V supports low-voltage and legacy 5 V sensor arrangements, but each attached circuit must remain within that range. Pull-up selection, bus capacitance, isolation boundaries, and grounding should be reviewed before connecting long sensor cables.

🏭

Programmable Logic Controller Expansion

The PCA9673D can expand a programmable logic controller or embedded automation controller when the base module has too few direct digital lines. Its remote 16-bit I/O capability is appropriate for connecting pushbuttons, mode controls, lamps, interlock signals, and discrete outputs while preserving a compact module footprint. Fast-mode Plus operation at up to 1 MHz provides useful bandwidth, although actual update rate depends on bus loading and the number of devices sharing the bus. The interrupt function supports change-driven control loops, while reset helps establish a known state during startup. Engineers should define each line as input or output only after checking the detailed configuration registers, and they should avoid driving outputs before the external circuit is initialized.

🔧

Test and Measurement Equipment

The PCA9673D is appropriate for test equipment that needs a deterministic register interface to front-panel controls, fixture selectors, relay drivers, and capture indicators. Consolidating these lines over I2C can reduce wiring between a controller board and an instrument interface, while the 1 MHz Fast-mode Plus capability supports reasonably rapid configuration updates. The reset function provides a practical mechanism for restoring the expansion interface when a test sequence begins, and the interrupt output can report asynchronous fixture or operator events. Supply sequencing and signal levels should be coordinated with the test system so that external loads remain off during reset. The 24-SOIC package requires a conventional SOIC land pattern and adequate clearance around neighboring components.

💡

LED and Display Control Interface

The PCA9673D can serve as the remote digital interface between a controller and grouped display or LED-driver boards. Instead of connecting every enable, mode, or segment-control signal directly to a microcontroller, the 16 lines can be managed through the I2C register interface at up to 1 MHz. This arrangement is especially useful in compact panels where connector pins and board area are constrained. Interrupt handling can report button or panel events, and reset can help coordinate panel initialization. The 2.3 V to 5.5 V device range supports both common logic levels, but the selected LED drivers, level shifters, and pull-ups must match the panel's voltage and current requirements. Confirm output timing and drive limits in the detailed electrical tables before connecting high-current loads directly.

🎥

Secure and Surveillance Peripheral Interface

The PCA9673D can extend a surveillance or access-control controller with digital lines for door contacts, request-to-exit buttons, alarm inputs, indicator outputs, and other peripheral signals. Remote I/O reduces the number of direct host GPIO connections and helps organize a multi-board installation around I2C. The interrupt output can alert the controller to a change on an external line, while reset supports controlled startup of the peripheral interface. Security equipment may use longer cable runs and electrically noisy relays, so designers should incorporate appropriate protection and isolation without exceeding the 2.3 V to 5.5 V supply limits. Bus pull-ups, grounding, shielding, and the location of the interrupt trace should be evaluated for the final mechanical and wiring environment.

What is the PCA9673D and what does it do?
The PCA9673D is a remote 16-bit I/O expander that adds 16 general-purpose lines to a host controller through an I2C bus. According to the manufacturer datasheet listing, it supports Fast-mode Plus operation at up to 1 MHz and includes interrupt and reset functions. It is useful when a microcontroller has insufficient GPIO pins for buttons, indicators, relays, sensors, or other discrete digital signals.
What is the I2C clock frequency of the PCA9673D?
The PCA9673D supports an I2C clock frequency of 1 MHz, as identified in the NXP device listing and datasheet description. This corresponds to Fast-mode Plus operation. Actual bus operation must still satisfy the timing, pull-up, capacitance, and voltage requirements of the complete circuit rather than relying on the maximum device rating alone.
What is the operating voltage range of PCA9673D?
The PCA9673D operates from 2.3 V to 5.5 V, according to the manufacturer datasheet information shown in the device listing. This range allows the expander to operate in 3.3 V and 5 V systems, subject to the voltage limits of the attached I2C devices, pull-ups, signal levels, and external load circuitry.
Where can I download the PCA9673D datasheet PDF?
The PCA9673D datasheet PDF is available through the linked NXP datasheet page, which identifies the device as a remote 16-bit I/O expander for Fast-mode Plus I2C with interrupt and reset. Use the manufacturer pin-description and electrical-characteristics tables when designing the PCB, programming registers, and checking operating limits.
What package does the PCA9673D use?
The PCA9673D is specified in a 24-SOIC package with a 0.295 inch, or 7.50 mm, body width. The listed package is a surface-mount SOIC outline. Verify the land pattern, pin numbering, exposed dimensions, and solder assembly requirements against the official package drawing before releasing the PCB.
Where can I find the PCA9673D pinout?
The PCA9673D pinout is located in the manufacturer datasheet's pin-description and package diagrams. The verified part listing confirms a 24-SOIC package, but it does not provide the individual signal names for all 24 terminals. Assign PCB nets only after checking those authoritative pin tables and accounting for the package orientation.
How is the PCA9673D different from a standard GPIO controller?
The PCA9673D expands digital I/O remotely over I2C instead of placing those functions directly inside the host microcontroller. Its documented 16 I/O lines and 1 MHz Fast-mode Plus interface can reduce direct host-GPIO consumption. The design must still allocate an I2C address, configure the device through its registers, and manage pull-ups and interrupt handling.
PCA9673D vs PCA9673D,118 — which ordering code should I choose?
PCA9673D,118 identifies the ordered NXP device configuration associated with the listed 24-SOIC version and cut-tape presentation, while PCA9673D is the base device designation. These are closely related order identifiers rather than functionally different designs. Confirm the full manufacturer ordering code, reel or cut-tape format, and packing quantity before procurement.
Can PCA9673D,118 replace PCA9673D without changing the PCB?
PCA9673D,118 can serve as the ordered form of the PCA9673D family when the PCB land pattern is the 24-SOIC footprint and the electrical requirements remain unchanged. The verified listing identifies both as an NXP 16-bit, 1 MHz I2C expander. Because the ordering suffix can also encode packing and shipment presentation, verify the complete ordering details before treating it as a production replacement.
When should I choose the PCA9673D instead of expanding a MCU with discrete logic?
Choose the PCA9673D when the host already has an I2C controller and the design needs multiple independently controlled digital inputs or outputs. The documented 16-line capacity can replace several host GPIO connections and separate logic ICs while preserving a register-based control interface. Use discrete logic instead when very low latency, unusual voltage levels, or simple one-off switching makes an I2C expander unnecessary.
Is the PCA9673D suitable for an STM32-based control board?
The PCA9673D is suitable for an STM32-based board when the STM32 I2C peripheral supports the required 1 MHz Fast-mode Plus operation and the external bus is electrically sound. The expander provides 16 lines over I2C and can support interrupt-driven event handling. Verify address availability, pull-up selection, bus capacitance, and level compatibility before finalizing the connection.
What is the lead time for PCA9673D?
Current lead time and production allocation for the PCA9673D should be requested through the Request a Quote form on this page. The product is shown as an active catalog device in current distributor listings, but those listings do not establish a guaranteed delivery interval. A dated commitment from the supplier is required for production planning.
Is PCA9673D in stock and how much does it cost?
Current availability and commercial terms for the PCA9673D should be confirmed with the Request a Quote form on this page. The verified listings show active distribution references but do not print a qualifying quantity-break table for this exact base MPN. This avoids presenting a stale single-unit figure as guaranteed current stock or contract pricing.
What is the best cross-brand equivalent for PCA9673D?
No cross-brand equivalent can be confirmed as a true drop-in replacement from the available cross-reference information. A candidate must use the same 24-SOIC footprint, match pin functions, support the same 2.3 V to 5.5 V range, provide 16 I/O lines, and preserve the required register and interrupt behavior. Use a verified device-specific comparison before changing manufacturers.
What are the key specifications of PCA9673D that engineers should know?
The key PCA9673D specifications are 16 remotely controlled I/O lines, a 1 MHz Fast-mode Plus I2C interface, a 2.3 V to 5.5 V operating range, interrupt and reset functions, and a 24-SOIC package. These parameters place the part in the remote I/O expander category and make it appropriate for embedded systems needing additional digital lines without allocating host-controller GPIO pins.

엔지니어링 참조 데이터: PCA9673D — 비교, 설계 지침 및 규정 준수 정보.

선택 가이드

Choose the PCA9673D when a host controller needs 16 additional digital lines and already has a suitable I2C controller. Its 1 MHz Fast-mode Plus interface, 2.3 V to 5.5 V supply range, interrupt capability, and reset function make it appropriate for compact industrial, monitoring, test, and display modules. Select PCA9673D,118 or PCA9673D,112 only after checking the full ordering code and required shipment presentation; the listings identify them as the same 24-SOIC device family rather than electrically upgraded alternatives. Do not choose a different package variant unless the PCB can be changed, and do not assume that another manufacturer's I/O expander is pin-compatible. A valid cross-brand substitute must preserve the 24-SOIC land pattern, 16 I/O lines, supply limits, register behavior, interrupt function, and timing requirements.

대체품과의 비교

파라미터 이 제품 PCA9673D,118 PCA9673D,112
Brand NXP Semiconductors NXP Semiconductors NXP Semiconductors
Package 24-SOIC 24-SOIC 24-SOIC
Number of I/O Lines 16 lines 16 lines 16 lines
Host Interface I2C I2C I2C
Maximum Clock Frequency 1 MHz 1 MHz 1 MHz
Supply Voltage Range 2.3 V to 5.5 V 2.3 V to 5.5 V 2.3 V to 5.5 V
I2C Mode Fast-mode Plus Fast-mode Plus Fast-mode Plus
Interrupt and Reset Supported Supported Supported
Ordering and Shipment Presentation Base PCA9673D designation ,118 ordering code associated with cut tape ,112 ordering code with 24-SO listing

주요 차별점

  • Provides 16 remote digital lines through a single I2C peripheral (vs PCA9673D,118)
  • Supports Fast-mode Plus operation across a broad supply range (vs PCA9673D,112)
  • Combines interrupt and reset functions in the remote I/O interface (vs PCA9673D,118)

설계 노트

Route SCL and SDA as short, continuous traces between the host controller and PCA9673D, and place the pull-up network near the bus master according to the system topology. Avoid stubs, test pads that add unnecessary capacitance, and routing through switching-power regions. Confirm the actual board-level capacitance against the Fast-mode Plus timing budget before operating the bus at the documented 1 MHz maximum.

Design the 2.3 V to 5.5 V supply rail to remain within the PCA9673D operating range under startup, reset, and load transients. Place local decoupling close to the supply and ground pins, with a short return path to the ground reference. If the expander controls relays, LEDs, or other switching loads, separate their supply paths from the I2C and logic rails to prevent transient coupling.

Do not assign PCB nets solely from the device ordering code. Confirm the 24-SOIC footprint, pin-one orientation, individual pin names, input or output direction, and active levels using the manufacturer pin-description and pinout tables. A base MPN, a cut-tape suffix, and a shipment-code suffix can describe the same electrical device while carrying different assembly or ordering requirements.

Review rise-time and fall-time behavior at the intended bus frequency rather than treating 1 MHz as a guaranteed system operating point. Pull-up strength affects rise time, while excessive capacitance slows transitions. Place the PCA9673D close enough to the host for a clean segment, use a continuous ground reference, and avoid crossing the I2C pair with noisy power or relay-routing boundaries.

규정 준수 정보

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
무연
Unknown
무할로겐
Unknown
분쟁 광물
Unknown

No specific RoHS, REACH, lead-free, halogen-free, conflict-minerals, or automotive qualification statement is included in the retrieved device information. AEC-Q100 is marked not applicable because this catalog device is not identified as an automotive-qualified variant.

데이터 검증일: 2026-11-14 — XAIPART 부품 엔지니어링 팀이 검증하고 관리한 데이터

관련 검색

PCA9673D datasheet PCA9673D datasheet pdf PCA9673D pinout PCA9673D 24-SOIC footprint PCA9673D 16-bit I2C expander PCA9673D 1MHz Fast-mode Plus PCA9673D 2.3V 5.5V PCA9673D equivalent PCA9673D replacement PCA9673D vs PCA9673D,118 PCA9673D application circuit NXP PCA9673D price PCA9673D stock and lead time PCA9673D GPIO expander for STM32

관련 부품 & 용어

NXP Semiconductors PCA9673D PCA9673D,118 PCA9673D,112 I/O expander GPIO expander remote I/O interface IC I2C Fast-mode Plus semiconductor embedded control 24-SOIC SOIC family surface mount SMD 16-bit I/O 1 MHz I2C clock 2.3 V to 5.5 V supply interrupt output reset function microcontroller STM32 sensor hub industrial control
빠른 견적 RFQ
상세 정보를 모두 입력하십시오 — 영업팀이 24시간 이내에 답변드립니다
부품 번호 제조사 패키지 QTY 목표 가격 합계
✓
견적이 제출되었습니다!

24시간 이내에 이메일로 답변드리겠습니다

1
RFQ 제출됨
2
견적 접수됨
3
주문 완료
4
결제
5
배송됨
6
배송 완료
RFQ 상세 보기