PEF20525FV1.3 - Serial Comm Controller SEROCCO-H | Infineon
N.º da peça: PEF20525FV1.3 ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $18.75 | $18,75 |
| 10 | $16.92 | $169,20 |
| 100 | $14.55 | $1.455,00 |
| 500 | $12.8 | $6.400,00 |
| 1.000 | $11.2 | $11.200,00 |
PEF20525FV1.3 Visão geral
A Telecom IC (also called a network controller or serial communications controller) is a specialized integrated circuit that offloads data link layer protocol processing from a host CPU. It sits between the physical layer transceiver and the host processor, implementing framing, CRC, and channel management for synchronous serial links. In the system hierarchy, it belongs to the interface IC / network controller & processor category of integrated circuits, enabling deterministic serial data flow in equipment such as ISDN terminal adapters, xDSL modems, and T/E-carrier interface cards.
Key features of the PEF20525FV1.3 include two independent serial channels with full-duplex operation, integrated PPP/HDLC framing support, hardware-assisted bit processing for low host CPU overhead, and flexible clocking for T-carrier and E-carrier telecom standards. The device also offers DMA-friendly host interface options and comprehensive interrupt/status reporting, allowing tight integration with embedded host processors.
The SEROCCO-H architecture combines dedicated hardware engines for HDLC/PPP framing, CRC generation and checking, and serial channel arbitration. This offloads heavy protocol processing from the host CPU, allowing the host to focus on higher-layer networking tasks. The dual-channel design enables simultaneous handling of two independent serial links, which is valuable for routers, gateways, and multi-port communication equipment.
Typical applications include ISDN terminal adapters, xDSL modems, T1/E1 interface cards, frame relay equipment, and embedded telecom modules for factory or industrial networking. The wide protocol support and dual-channel capability make it suitable for any application requiring deterministic serial data link processing.
When designing with the PEF20525FV1.3, ensure proper decoupling near the supply pins and follow Infineon's reference layout for the PG-TQFP-100-3 package. The host interface should be configured according to the chosen bus width and endianness to minimize glue complexity. Designers should also verify the latest firmware/driver support matrix from Infineon for their specific host processor family.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para PEF20525FV1.3 — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PEF20525FV1.1
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PEF20525FV1.2
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PEF20525FV1.3 Especificações
| Product Type | Telecom IC / Serial Communication Controller |
| Series | SEROCCO-H |
| Função | Serial Optimized Communications Controller |
| Number of Serial Channels | 2 (independent, full-duplex) |
| Protocol Support | PPP / HDLC |
| Encapsulamento | PG-TQFP-100-3 (100-pin TQFP) |
| Tipo de montagem | Surface Mount |
| Interface | Parallel host bus (DMA-friendly) |
| Operating Mode | Full-duplex serial data link |
| Application Domain | Telecom / Networking |
| Architecture | Dedicated HDLC/PPP hardware engines |
| Contagem de pinos | 100 |
| Status RoHS | Compliant |
| Lead-Free | Yes |
Guia de Configuração de Pinos do PEF20525FV1.3 pg-tqfp-100-3 (100-pin tqfp)
Configuração de pinos para PEF20525FV1.3 (pacote pg-tqfp-100-3 (100-pin tqfp)). A numeração dos pinos, funções e diagramas de conexão estão definidos no datasheet do fabricante. Consulte-o para o footprint exato e diretrizes de soldagem.
Nenhum dado detalhado de pinagem disponível para PEF20525FV1.3.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PEF20525FV1.3 é adequado para 7 aplicaçãos: ISDN Terminal Adapter, xDSL Modem / CPE, T1/E1 Interface Card, Frame Relay Router, Industrial Serial Gateway, Embedded Telecom Module, VoIP Gateway / Media Gateway.
ISDN Terminal Adapter
The PEF20525FV1.3's dual independent serial channels and integrated PPP/HDLC hardware engines make it well suited for ISDN terminal adapters that must terminate two B-channels simultaneously. Placing the device between the ISDN transceiver and the host CPU offloads bit-level framing and CRC computation, freeing the host for higher-layer PPP and IP processing. Compared with a software stack, the hardware offload reduces interrupt load and improves sustained throughput on both B-channels.
Recomendado
xDSL Modem / CPE
In xDSL customer premises equipment, the PEF20525FV1.3 handles the PPP/HDLC link layer required by PPPoE and PPPoA framing between the DSL modem chipset and the host processor. Its dual-channel capability allows the device to terminate both a primary data channel and a secondary management channel concurrently. The PG-TQFP-100-3 surface-mount package integrates cleanly into the dense PCB layout typical of xDSL CPE designs.
Recomendado
T1/E1 Interface Card
For T1/E1 interface cards used in enterprise routers and PBXs, the PEF20525FV1.3 provides two independent serial channels aligned with T1/E1 framing requirements. Its hardware HDLC engine handles bit stuffing and CRC with deterministic latency, critical for telecom timing budgets. The PG-TQFP-100-3 package supports the thermal and mechanical requirements of multi-port line cards where several instances can populate a single board.
Recomendado
Frame Relay Router
The PEF20525FV1.3's PPP/HDLC support is also applicable to legacy frame relay equipment and routers that require HDLC-based link layer termination. The device's dual channels permit termination of two frame relay PVCs on a single IC, reducing board area and BOM cost. Its DMA-friendly host interface integrates with embedded networking processors to deliver deterministic throughput under heavy PVC load.
Recomendado
Industrial Serial Gateway
Industrial serial gateways that bridge legacy synchronous serial equipment into modern Ethernet networks benefit from the PEF20525FV1.3's hardware HDLC/PPP offload and dual-channel design. The device provides reliable, deterministic serial link termination that is immune to host CPU loading variations, important in industrial automation environments where timing jitter is unacceptable.
Recomendado
Embedded Telecom Module
Embedded telecom modules (router-on-a-module, mezzanine route cards) leverage the PEF20525FV1.3 to provide two independent serial data link terminations in a small footprint. The PG-TQFP-100-3 package supports the compact module dimensions while exposing parallel host bus pins for direct attachment to a host carrier board. The hardware PPP/HDLC acceleration enables consistent throughput regardless of host processor capability.
Recomendado
VoIP Gateway / Media Gateway
In VoIP gateway and media gateway designs, the PEF20525FV1.3 terminates the PSTN-side serial link (T1/E1 or BRI) while the host processor handles VoIP packetization and signaling. The device's hardware HDLC engine supports PRI/BRI link-layer channels, while the dual-channel capability accommodates primary rate T1/E1 or multiple BRI interfaces. This separation of concerns simplifies firmware development and improves voice quality by offloading critical real-time tasks.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PEF20525FV1.3 — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PEF20525FV1.1 | PEF20525FV1.2 |
|---|---|---|---|
| Brand | Infineon Technologies | Infineon Technologies | Infineon Technologies |
| Package | PG-TQFP-100-3 | PG-TQFP-100-3 - same | PG-TQFP-100-3 - same |
| Firmware Revision | V1.3 | V1.1 (earlier) | V1.2 (earlier) |
| Number of Serial Channels | 2 | 2 | 2 |
| Protocol Support | PPP / HDLC | PPP / HDLC | PPP / HDLC |
| Host Interface | Parallel host bus (DMA-friendly) | Parallel host bus (DMA-friendly) | Parallel host bus (DMA-friendly) |
| Mounting Type | Surface Mount | Surface Mount | Surface Mount |
| RoHS Compliance | Compliant | Compliant | Compliant |
| Series | SEROCCO-H | SEROCCO-H | SEROCCO-H |
Principais diferenciais
- Dual-channel hardware PPP/HDLC offload in a single IC (vs PEF20525FV1.1)
- SEROCCO-H family with mature Infineon telecom ecosystem (vs Generic software PPP on host CPU)
- DMA-friendly parallel host interface (vs Serial-controlled serial comm ICs)
Notas de projeto
The PEF20525FV1.3 requires a clean 3.3 V supply rail for its core and I/O. Place a 100 nF decoupling capacitor close to each supply pin group, plus a 10 uF bulk capacitor near the IC. Avoid sharing the supply with high-current switching regulators - use a ferrite bead or LDO to isolate the telecom IC from noisy digital rails. Ground returns should be low-impedance to prevent logic noise coupling into the serial channels.
The PG-TQFP-100-3 package requires a 0.50 mm pitch footprint with proper thermal pad soldering per JEDEC J-STD-020 reflow guidelines. Route serial channel differential pairs with matched lengths and 100 ohm differential impedance if applicable. Keep clock traces short and isolated from the host bus to minimize crosstalk. Provide a continuous ground plane beneath the device to reduce EMI radiation.
Do not assume any cross-brand drop-in equivalent exists for the PEF20525FV1.3 - the SEROCCO-H architecture is unique to Infineon. If you must replace this part, evaluate within-family variants (PEF20525FV1.1, PEF20525FV1.2) or migrate to the next-generation SEROCCO family with a host-side software update. Verify firmware revision compatibility with your host driver before swapping revisions in production.
Informações de conformidade
RoHS compliant per Infineon product declaration and distributor listings. Not AEC-Q100 qualified - this is a commercial/industrial telecom IC. Lead-free assembly supported.
