Diodes Incorporated

PI7C9X1170ACLEX - I2C/SPI to UART Bridge | Diodes

N.º da peça: PI7C9X1170ACLEX ✓ Ativo
1.62 V to 3.63 V Vdss 24-pin TSSOP Package
MOQ: 1 |

PI7C9X1170ACLEX Visão geral

Diodes Incorporated PI7C9X1170ACLEX is an I2C-bus/SPI-to-UART bridge controller with 64-byte transmit and receive FIFOs, supplied in a 24-pin TSSOP package. It operates from 1.62 V to 3.63 V and supports industrial-temperature applications. The device provides a bridge between serial protocols used by embedded processors and peripheral controllers.

An I2C-to-UART bridge is a protocol-conversion interface IC within the broader hierarchy of interface integrated circuits, serial controllers, and semiconductors. Its purpose is to transfer commands or data across incompatible serial interfaces while buffering traffic through dedicated FIFOs. The PI7C9X1170ACLEX combines an I2C controller, an SPI interface, and a UART interface in one package, reducing the need for separate discrete interface components.

Key features include 64-byte TX and RX FIFOs, support for Standard-mode and Fast-mode I2C-bus operation, and a 1.62 V to 3.63 V operating-voltage range. These features make the controller useful where a host processor needs a compact, low-voltage serial bridge. The 24-terminal TSSOP package supports surface-mount PCB assembly and is available in a 3000-piece tape-and-reel format.

The bridge architecture separates upstream I2C or SPI transactions from UART output through internal buffering. The FIFOs help accommodate short periods of mismatch between host-side request rates and UART data consumption. Exact baud-rate options, electrical timing limits, pin assignments, and supported clock configurations should be confirmed in the manufacturer datasheet before finalizing a high-speed interface design.

Typical applications include embedded-system service interfaces, industrial controllers, programmable logic device configuration, memory-programming systems, instrument-control boards, and host-to-peripheral data links. In each case, the controller allows an embedded processor to communicate through UART while using I2C or SPI as the control-side bus.

PCB design should preserve short, clean routes between the bridge and its host connector or processor. Keep UART signal routing away from high-speed clock and SPI nets, provide clean ground returns, and verify logic levels against every connected device. The 1.62 V to 3.63 V supply range also makes input- and output-level compatibility a central system-design check.

This product page consolidates the device interface, package, voltage, FIFO, and sourcing details with practical replacement and PCB guidance. It supports engineers comparing the PI7C9X1170ACLEX with same-footprint controller options while keeping the selection focused on verified pin and parameter compatibility.

Alternativas drop-in para PI7C9X1170ACLEX — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.

PI7C9X1170ACLE

✅ Drop-In
📦 24-TSSOP
Same 24-pin TSSOP I2C/SPI-to-UART controller package; ordering-suffix temperature-grade details require confirmation

📋 Alternativa de referência (fora do catálogo)

PI7C9X1170ACLEX Classificações máximas e características elétricas

Device Type 1 I2C-bus/SPI-to-UART bridge controller
Supply Voltage Range 1.62 V to 3.63 V
I2C Interface 1 Standard-mode and Fast-mode I2C-bus interface
SPI Interface 1 serial peripheral interface
UART Interface 1 UART interface
Transmit FIFO 64 bytes
Receive FIFO 64 bytes
Operating Temperature Grade Industrial grade
Encapsulamento 24-pin TSSOP
Terminal Shape Gull wing
Package Body Width 4.40 mm
Lead Pitch 0.65 mm
Tipo de montagem Surface mount
Shipping Format Tape and reel
Standard Reel Quantity 3000 pieces

Guia de Configuração de Pinos do PI7C9X1170ACLEX 4.40 mm

Configuração de pinos para PI7C9X1170ACLEX (pacote 4.40 mm). Este dispositivo de potência possui terminais de gate, drain e source. Para pacotes não polarizados, consulte o datasheet do fabricante para a orientação exata do pino 1 e detalhes do footprint. Aplicações comuns incluem projeto de fontes de alimentação, acionamento de motores e comutação de cargas.

Diagrama de pinagem do pacote 4.40 mm para PI7C9X1170ACLEX

Nenhum dado detalhado de pinagem disponível para PI7C9X1170ACLEX.

Consulte a ficha técnica para a configuração completa dos pinos.

Aplicações típicas

PI7C9X1170ACLEX é adequado para 6 aplicaçãos: Embedded Processor Service Interfaces, Programmable Logic Device Configuration, Industrial Controller Communication, Memory Programming and Test Systems, Instrument and Measurement Control, IoT and Smart-Device Gateways.

🔧

Embedded Processor Service Interfaces

The PI7C9X1170ACLEX fits an embedded processor that must expose configuration or maintenance data through a UART connector while using I2C or SPI internally. The host-side bus can command the bridge, and the 64-byte transmit and receive FIFOs buffer data on both sides of the protocol conversion. Its 1.62 V to 3.63 V operating range suits low-voltage systems, while the 24-pin TSSOP reduces board area. Confirm signal-level compatibility with the processor and connector electronics, and size the host protocol around the documented FIFO and timing limits.

🖥️

Programmable Logic Device Configuration

The PI7C9X1170ACLEX can serve as the serial interface between a control processor and a programmable logic device or configuration controller. I2C or SPI provides a compact host connection, while UART carries the data stream expected by the target device. Separate 64-byte TX and RX FIFOs help accommodate asynchronous command and response traffic. The 1.62 V to 3.63 V supply range supports compact embedded systems, but the board designer must match all logic levels and verify configuration timing against the target device.

🏭

Industrial Controller Communication

PI7C9X1170ACLEX is suitable for industrial controller boards that need to bridge a board-level I2C or SPI management bus to a legacy UART peripheral. Its industrial temperature-grade ordering designation supports equipment intended for controlled industrial environments. The 64-byte transmit and receive FIFOs are useful when the controller processes commands irregularly but the UART peripheral requires a continuous byte stream. The design must provide a stable low-voltage supply, common grounding, and logic-level compatibility across the I2C, SPI, and UART domains.

⚡

Memory Programming and Test Systems

The PI7C9X1170ACLEX can bridge a system controller to a programming fixture that communicates through UART while configuration data originates from an I2C or SPI source. Buffered transfer reduces the risk that temporary host-side processing delays interrupt the data stream. The 24-pin TSSOP footprint supports compact interface sections on automated test equipment. Before implementation, confirm the supported UART baud rates, I2C mode, SPI timing, reset behavior, and maximum frame handling requirements in the manufacturer datasheet for the target production volume.

🔧

Instrument and Measurement Control

A PI7C9X1170ACLEX-based interface can connect a compact control board to an instrument peripheral that exposes a UART service port while accepting setup commands through I2C or SPI. This mixed-protocol arrangement is useful in laboratory equipment where an internal embedded processor communicates through a convenient serial bus but legacy subsystems remain UART-based. The 64-byte TX and RX FIFOs accommodate command-response traffic, and the 1.62 V to 3.63 V range fits modern low-voltage logic. Keep sensitive analog routing separate from UART and SPI traces.

🧩

IoT and Smart-Device Gateways

The PI7C9X1170ACLEX can act as a protocol bridge within a compact IoT gateway or smart-device controller. A sensor or radio subsystem connected through I2C or SPI can exchange data with a host-facing UART module without requiring a separate bridge IC for each interface combination. The 24-pin TSSOP conserves board area, and the 64-byte FIFOs support bursty sensor or command traffic. Use the manufacturer timing data to establish polling behavior, and ensure the UART link's logic levels and baud rate match the selected wireless or host module.

What is PI7C9X1170ACLEX?
The Diodes Incorporated PI7C9X1170ACLEX is an I2C-bus/SPI-to-UART bridge controller with 64-byte transmit and receive FIFOs. According to the manufacturer datasheet, its I2C interface complies with Standard-mode and Fast-mode I2C-bus specifications. The controller operates from 1.62 V to 3.63 V and is packaged in a 24-pin TSSOP for surface-mount assembly.
Where can I download the PI7C9X1170ACLEX datasheet PDF?
The PI7C9X1170ACLEX datasheet PDF is available from the manufacturer-linked document at the datasheet URL on this page. It is the appropriate document for confirming the complete 24-pin assignment, electrical characteristics, timing limits, FIFO behavior, and recommended application circuit. Use the pin-description table in that datasheet when assigning PCB tracks and connector signals.
Where can I find the PI7C9X1170ACLEX pinout?
The PI7C9X1170ACLEX uses a 24-pin TSSOP package, and its complete pin assignment is defined in the manufacturer datasheet. Locate the 24-pin package drawing and pin-description table in that document, then match pin numbers to the TSSOP-24 footprint. The package uses 0.65 mm lead pitch, so PCB design should follow the land pattern specified for the exact ordering code.
What are the key specifications of PI7C9X1170ACLEX that engineers should know?
The PI7C9X1170ACLEX combines I2C-bus, SPI, and UART interfaces in a 24-pin TSSOP package. Its principal specifications include a 1.62 V to 3.63 V operating range, Standard-mode and Fast-mode I2C compliance, and separate 64-byte transmit and receive FIFOs. According to the manufacturer datasheet, the I2C side uses SDA and SCL, while the UART and SPI interfaces provide the alternate serial communication paths.
Is PI7C9X1170ACLEX suitable for low-voltage embedded systems?
The PI7C9X1170ACLEX is suitable for low-voltage embedded systems operating within 1.62 V to 3.63 V. Its integrated I2C/SPI-to-UART bridge eliminates the need for separate controllers when a host must access a UART peripheral through I2C or SPI. Confirm that every connected device uses compatible signal levels and that the selected I2C operating mode satisfies the system timing requirements.
What can replace PI7C9X1170ACLEX?
The PI7C9X1170ACLE is the closest documented same-footprint replacement candidate for the PI7C9X1170ACLEX because it is also a Diodes Incorporated 24-pin TSSOP I2C/SPI-to-UART bridge controller. Its ordering suffix differs, so temperature-grade and qualification requirements should be checked before substitution. The PI7C9X1170ABLEX is not pin-compatible because it uses a 16-pin TSSOP package.
Is PI7C9X1170ACLEX the same as PI7C9X1170ACLE?
The PI7C9X1170ACLEX and PI7C9X1170ACLE share the same 24-pin TSSOP format and are identified as I2C/SPI-to-UART bridge controllers. They are not confirmed as identical in every environmental or ordering characteristic because the suffix distinction must be checked against the manufacturer ordering guide. Verify pin definitions, temperature grade, lifecycle status, and production configuration before approving either part as a substitute.
Where can I buy PI7C9X1170ACLEX online?
The PI7C9X1170ACLEX can be requested through the Request a Quote form on this page. The form is the appropriate route for checking availability, order quantity, and lead time for the exact 24-pin TSSOP ordering code. Specify PI7C9X1170ACLEX exactly and confirm the 3000-piece tape-and-reel format when preparing the requisition.
What is the price of PI7C9X1170ACLEX?
The current commercial price for PI7C9X1170ACLEX should be obtained through the Request a Quote form on this page. Submit the exact MPN, required quantity, and preferred tape-and-reel packaging for a current quotation. The structured pricing system will account for market availability and quantity breaks without embedding a stale price in the technical content.
What is the lead time for PI7C9X1170ACLEX?
The current lead time for PI7C9X1170ACLEX should be confirmed through the Request a Quote form on this page. Include your required quantity and target delivery date in the request. The manufacturer offers the exact MPN in a 24-pin TSSOP tape-and-reel format, and the quotation workflow can establish current production and scheduling availability.
Is PI7C9X1170ACLEX in stock?
Current PI7C9X1170ACLEX stock should be checked through the Request a Quote form on this page. Provide the required quantity, shipment destination, and preferred delivery schedule so the order can be matched to available inventory. The exact MPN and its 24-pin TSSOP configuration should be stated in the request to avoid confusion with the 16-pin PI7C9X1170ABLEX.
PI7C9X1170ACLEX vs PI7C9X1170ACLE - which is better?
Both PI7C9X1170ACLEX and PI7C9X1170ACLE are documented as Diodes Incorporated 24-pin TSSOP I2C/SPI-to-UART bridge controllers, making them the relevant comparison pair for footprint reuse. Choose the exact ordering code whose temperature grade and qualification match the product requirements. Do not substitute PI7C9X1170ABLEX because that device has 16 pins rather than 24.
What is the difference between PI7C9X1170ACLEX and PI7C9X1170ABLEX?
The PI7C9X1170ACLEX uses a 24-pin TSSOP package, while the PI7C9X1170ABLEX uses a 16-pin TSSOP package. Both belong to the PI7C9X1170 controller family and provide I2C/SPI-to-UART bridging, but their pin counts differ. The 16-pin device is therefore not a drop-in replacement and requires a different PCB footprint and pin assignment.
When should I choose PI7C9X1170ACLEX over PI7C9X1170ACLE?
Choose PI7C9X1170ACLEX when the finished equipment requires the exact industrial-grade ordering configuration associated with that suffix. Choose PI7C9X1170ACLE only after its temperature range, qualification, and ordering details have been confirmed against the design requirements. Both use the 24-pin TSSOP footprint, making the suffix specification—not the package outline—the decisive compatibility check.
Does PI7C9X1170ACLEX comply with RoHS and REACH?
The PI7C9X1170ACLEX RoHS and REACH status should be confirmed from the current manufacturer product declaration or material-compliance documentation. Those compliance statements are not printed in the manufacturer datasheet passage available on this page. Request the applicable declaration before release, particularly when the product is used in industrial equipment subject to customer-specific environmental requirements.

Dados de referência de engenharia para PI7C9X1170ACLEX — comparação, orientação de projeto e informações de conformidade.

Guia de seleção

Choose PI7C9X1170ACLEX when a low-voltage embedded design requires one controller to bridge an I2C-bus or SPI host connection to a UART peripheral. Its 64-byte TX and RX FIFOs, 1.62 V to 3.63 V operating range, and 24-pin TSSOP package make it suitable for compact industrial, test, instrumentation, and IoT interface sections. PI7C9X1170ACLE is the closest documented same-footprint candidate when its ordering suffix provides the required temperature grade and qualification. Do not select PI7C9X1170ABLEX as a drop-in replacement because its 16-pin TSSOP package is not compatible with the 24-pin footprint. Before final release, verify the exact pin map, electrical timing, UART baud-rate options, SPI clock limits, FIFO semantics, and logic-level thresholds against the manufacturer datasheet.

Comparação com alternativas

Parâmetro Este produto PI7C9X1170ACLE
Brand Diodes Incorporated Diodes Incorporated
Package 24-TSSOP 24-TSSOP - same
Device Function I2C/SPI-to-UART bridge controller I2C/SPI-to-UART bridge controller

Principais diferenciais

  • Provides both transmit and receive buffering in one bridge controller (vs PI7C9X1170ACLE)
  • Combines three serial protocols in a 24-pin interface IC (vs PI7C9X1170ABLEX)
  • Supports a 1.62 V to 3.63 V operating range (vs PI7C9X1170ACLE)

Notas de projeto

Route the I2C SDA and SCL lines, SPI signals, and UART data as a compact serial interface group while keeping them away from switching nodes and analog inputs. Provide a continuous ground reference beneath the device and return high-speed or high-current traces to a quiet ground region. The 24-pin TSSOP uses a 0.65 mm lead pitch, so follow the manufacturer land pattern and inspect the assembled board for solder bridges between adjacent leads.

Design the PI7C9X1170ACLEX supply for the full 1.62 V to 3.63 V operating range and ensure every connected I2C, SPI, and UART device uses compatible logic levels. Place local supply-decoupling capacitance at the power pins and keep the return path short. Mixed-voltage systems may require level translation on the UART or SPI side if their input and output thresholds do not overlap the bridge's logic specification.

Do not treat the PI7C9X1170ABLEX as a drop-in alternative because it has 16 pins rather than 24. The PI7C9X1170ACLE is the documented 24-pin candidate, but its suffix-specific temperature and qualification requirements must still be confirmed. Also verify FIFO depth, baud-rate support, reset behavior, and interface timing against the manufacturer datasheet rather than relying only on the shared bridge-controller description.

Informações de conformidade

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Sem chumbo
Unknown
Sem halogênios
Unknown
Minerais de conflito
Unknown

The interface controller is an industrial-temperature-grade product, but no AEC-Q100 qualification statement is documented. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer.

Dados verificados em: 2026-11-17 — dados verificados e curados pela equipe de engenharia de componentes da XAIPART

Buscas relacionadas

PI7C9X1170ACLEX datasheet PI7C9X1170ACLEX specifications PI7C9X1170ACLEX pinout PI7C9X1170ACLEX datasheet pdf PI7C9X1170ACLEX equivalent PI7C9X1170ACLEX replacement PI7C9X1170ACLEX cross reference PI7C9X1170ACLEX vs PI7C9X1170ACLE PI7C9X1170ACLEX 24-TSSOP PI7C9X1170ACLEX price PI7C9X1170ACLEX stock Diodes PI7C9X1170ACLEX PI7C9X1170ACLEX I2C SPI UART PI7C9X1170ACLEX 64 byte FIFO

Componentes & termos relacionados

Diodes Incorporated PI7C9X1170ACLEX PI7C9X1170ACLE PI7C9X1170ABLEX I2C bridge controller SPI-to-UART bridge UART interface IC serial interface controller interface integrated circuit semiconductor I2C-bus SPI UART SDA SCL Standard-mode I2C Fast-mode I2C 64-byte TX FIFO 64-byte RX FIFO 1.62 V to 3.63 V 24-pin TSSOP TSSOP package family surface-mount device industrial-grade electronics
RFQ de cotação rápida
Preencha todos os detalhes — nossa equipe de vendas responderá em até 24 horas
Part number Fabricante Encapsulamento QTY Preço-alvo Total
✓
Cotação enviada!

Responderemos seu e-mail em até 24 horas

1
RFQ enviada
2
Cotação recebida
3
Pedido realizado
4
Pagamento
5
Enviado
6
Entregue
Ver detalhes da RFQ