PI7C9X1170ACLEX - I2C/SPI to UART Bridge | Diodes
MPN: PI7C9X1170ACLEX ✓ Hoạt độngPI7C9X1170ACLEX Tóm tắt
An I2C-to-UART bridge is a protocol-conversion interface IC within the broader hierarchy of interface integrated circuits, serial controllers, and semiconductors. Its purpose is to transfer commands or data across incompatible serial interfaces while buffering traffic through dedicated FIFOs. The PI7C9X1170ACLEX combines an I2C controller, an SPI interface, and a UART interface in one package, reducing the need for separate discrete interface components.
Key features include 64-byte TX and RX FIFOs, support for Standard-mode and Fast-mode I2C-bus operation, and a 1.62 V to 3.63 V operating-voltage range. These features make the controller useful where a host processor needs a compact, low-voltage serial bridge. The 24-terminal TSSOP package supports surface-mount PCB assembly and is available in a 3000-piece tape-and-reel format.
The bridge architecture separates upstream I2C or SPI transactions from UART output through internal buffering. The FIFOs help accommodate short periods of mismatch between host-side request rates and UART data consumption. Exact baud-rate options, electrical timing limits, pin assignments, and supported clock configurations should be confirmed in the manufacturer datasheet before finalizing a high-speed interface design.
Typical applications include embedded-system service interfaces, industrial controllers, programmable logic device configuration, memory-programming systems, instrument-control boards, and host-to-peripheral data links. In each case, the controller allows an embedded processor to communicate through UART while using I2C or SPI as the control-side bus.
PCB design should preserve short, clean routes between the bridge and its host connector or processor. Keep UART signal routing away from high-speed clock and SPI nets, provide clean ground returns, and verify logic levels against every connected device. The 1.62 V to 3.63 V supply range also makes input- and output-level compatibility a central system-design check.
This product page consolidates the device interface, package, voltage, FIFO, and sourcing details with practical replacement and PCB guidance. It supports engineers comparing the PI7C9X1170ACLEX with same-footprint controller options while keeping the selection focused on verified pin and parameter compatibility.
Bộ thay thế dễ dàng lắp đặt cho PI7C9X1170ACLEX — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
PI7C9X1170ACLE
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
PI7C9X1170ACLEX Tỷ lệ tối đa & tính chất điện
| Device Type | 1 I2C-bus/SPI-to-UART bridge controller |
| Supply Voltage Range | 1.62 V to 3.63 V |
| I2C Interface | 1 Standard-mode and Fast-mode I2C-bus interface |
| SPI Interface | 1 serial peripheral interface |
| UART Interface | 1 UART interface |
| Transmit FIFO | 64 bytes |
| Receive FIFO | 64 bytes |
| Operating Temperature Grade | Industrial grade |
| Hộp | 24-pin TSSOP |
| Terminal Shape | Gull wing |
| Package Body Width | 4.40 mm |
| Lead Pitch | 0.65 mm |
| Kiểu lắp đặt | Surface mount |
| Shipping Format | Tape and reel |
| Standard Reel Quantity | 3000 pieces |
Hướng dẫn cấu hình chân PI7C9X1170ACLEX 4.40 mm
Cấu hình chân cho PI7C9X1170ACLEX (4.40 mm gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho PI7C9X1170ACLEX.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
PI7C9X1170ACLEX phù hợp cho 6 Áp dụngs: Embedded Processor Service Interfaces, Programmable Logic Device Configuration, Industrial Controller Communication, Memory Programming and Test Systems, Instrument and Measurement Control, IoT and Smart-Device Gateways.
Embedded Processor Service Interfaces
The PI7C9X1170ACLEX fits an embedded processor that must expose configuration or maintenance data through a UART connector while using I2C or SPI internally. The host-side bus can command the bridge, and the 64-byte transmit and receive FIFOs buffer data on both sides of the protocol conversion. Its 1.62 V to 3.63 V operating range suits low-voltage systems, while the 24-pin TSSOP reduces board area. Confirm signal-level compatibility with the processor and connector electronics, and size the host protocol around the documented FIFO and timing limits.
Được đề xuất
Programmable Logic Device Configuration
The PI7C9X1170ACLEX can serve as the serial interface between a control processor and a programmable logic device or configuration controller. I2C or SPI provides a compact host connection, while UART carries the data stream expected by the target device. Separate 64-byte TX and RX FIFOs help accommodate asynchronous command and response traffic. The 1.62 V to 3.63 V supply range supports compact embedded systems, but the board designer must match all logic levels and verify configuration timing against the target device.
Được đề xuất
Industrial Controller Communication
PI7C9X1170ACLEX is suitable for industrial controller boards that need to bridge a board-level I2C or SPI management bus to a legacy UART peripheral. Its industrial temperature-grade ordering designation supports equipment intended for controlled industrial environments. The 64-byte transmit and receive FIFOs are useful when the controller processes commands irregularly but the UART peripheral requires a continuous byte stream. The design must provide a stable low-voltage supply, common grounding, and logic-level compatibility across the I2C, SPI, and UART domains.
Được đề xuất
Memory Programming and Test Systems
The PI7C9X1170ACLEX can bridge a system controller to a programming fixture that communicates through UART while configuration data originates from an I2C or SPI source. Buffered transfer reduces the risk that temporary host-side processing delays interrupt the data stream. The 24-pin TSSOP footprint supports compact interface sections on automated test equipment. Before implementation, confirm the supported UART baud rates, I2C mode, SPI timing, reset behavior, and maximum frame handling requirements in the manufacturer datasheet for the target production volume.
Được đề xuất
Instrument and Measurement Control
A PI7C9X1170ACLEX-based interface can connect a compact control board to an instrument peripheral that exposes a UART service port while accepting setup commands through I2C or SPI. This mixed-protocol arrangement is useful in laboratory equipment where an internal embedded processor communicates through a convenient serial bus but legacy subsystems remain UART-based. The 64-byte TX and RX FIFOs accommodate command-response traffic, and the 1.62 V to 3.63 V range fits modern low-voltage logic. Keep sensitive analog routing separate from UART and SPI traces.
Được đề xuất
IoT and Smart-Device Gateways
The PI7C9X1170ACLEX can act as a protocol bridge within a compact IoT gateway or smart-device controller. A sensor or radio subsystem connected through I2C or SPI can exchange data with a host-facing UART module without requiring a separate bridge IC for each interface combination. The 24-pin TSSOP conserves board area, and the 64-byte FIFOs support bursty sensor or command traffic. Use the manufacturer timing data to establish polling behavior, and ensure the UART link's logic levels and baud rate match the selected wireless or host module.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho PI7C9X1170ACLEX — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | PI7C9X1170ACLE |
|---|---|---|
| Brand | Diodes Incorporated | Diodes Incorporated |
| Package | 24-TSSOP | 24-TSSOP - same |
| Device Function | I2C/SPI-to-UART bridge controller | I2C/SPI-to-UART bridge controller |
Bảo phân biệt quan trọng
- Provides both transmit and receive buffering in one bridge controller (vsPI7C9X1170ACLE)
- Combines three serial protocols in a 24-pin interface IC (vsPI7C9X1170ABLEX)
- Supports a 1.62 V to 3.63 V operating range (vsPI7C9X1170ACLE)
Ghi chú thiết kế
Route the I2C SDA and SCL lines, SPI signals, and UART data as a compact serial interface group while keeping them away from switching nodes and analog inputs. Provide a continuous ground reference beneath the device and return high-speed or high-current traces to a quiet ground region. The 24-pin TSSOP uses a 0.65 mm lead pitch, so follow the manufacturer land pattern and inspect the assembled board for solder bridges between adjacent leads.
Design the PI7C9X1170ACLEX supply for the full 1.62 V to 3.63 V operating range and ensure every connected I2C, SPI, and UART device uses compatible logic levels. Place local supply-decoupling capacitance at the power pins and keep the return path short. Mixed-voltage systems may require level translation on the UART or SPI side if their input and output thresholds do not overlap the bridge's logic specification.
Do not treat the PI7C9X1170ABLEX as a drop-in alternative because it has 16 pins rather than 24. The PI7C9X1170ACLE is the documented 24-pin candidate, but its suffix-specific temperature and qualification requirements must still be confirmed. Also verify FIFO depth, baud-rate support, reset behavior, and interface timing against the manufacturer datasheet rather than relying only on the shared bridge-controller description.
Thông tin tuân thủ
The interface controller is an industrial-temperature-grade product, but no AEC-Q100 qualification statement is documented. RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the manufacturer.