PIC16C65A-20I/L - 8-Bit 20MHz OTP MCU 7KB EPROM 44-PLCC | Microchip
N.º da peça: PIC16C65A-20I/L ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.18 | $7,18 |
| 10 | $6.84 | $68,40 |
| 100 | $6.12 | $612,00 |
| 500 | $5.41 | $2.705,00 |
| 1.000 | $4.78 | $4.780,00 |
PIC16C65A-20I/L Visão geral
A PIC microcontroller is a Harvard-architecture RISC device that integrates a CPU, non-volatile program memory, RAM, and peripherals (timers, ADC, USART, I/O) into a single chip. PIC microcontrollers sit within the broader category of microcontrollers -> microcomputers -> semiconductors, and the PIC16C sub-family specifically targets low-power, high-throughput embedded control with 35 single-word instructions, single-cycle execution (except branches which take two cycles), and a fully static design.
Key features of the PIC16C65A-20I/L include a wide operating voltage range of 2.5 V to 6.0 V, low power consumption of 15 uA typical at 5 V / 4 MHz and 1 uA typical at 3 V / 32 kHz, and an integrated peripheral set with timers, capture/compare/PWM modules, a synchronous/asynchronous serial port (USART/SCI), and a parallel slave port. The wide operating voltage supports both 3.3 V and 5 V system designs, while the OTP memory is one-time programmable for low-cost, high-volume production.
The architecture uses a 14-bit instruction word with an 8-bit data path and a 35-instruction RISC core, enabling deterministic single-cycle execution (200 ns per instruction at 20 MHz). The fully static design supports DC operation down to 0 Hz, useful for clock-synchronous power-saving modes.
Typical applications include industrial automation controllers, motor control front-ends, embedded instrumentation, and legacy equipment retrofits. The 33 I/O pins and parallel slave port allow direct interface to external memories, keypads, displays, and analog front-ends. The wide 2.5 V to 6.0 V supply range also suits battery-powered and automotive 12 V-bus systems with simple regulators.
When designing with this device, account for OTP memory limitations: once programmed, the firmware cannot be changed. For prototyping or field-updatable firmware, prefer the flash-based PIC16F877A in the same 44-pin PLCC footprint. Always validate interrupt latency and branch-cycle timing against the 200 ns instruction budget for time-critical routines.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para PIC16C65A-20I/L — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16C65A-20I/L (mesmo formato e footprint) — diferindo em Program Memory Size, Operating Temperature, Mounting Type, Core Architecture, Package.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16C65B-20I/L
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$8.4 / unidade
Ver ficha técnica →PIC16C66-20I/L
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16C67-20I/L
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$6.75 / unidade
Ver ficha técnica →PIC16F877A-I/L
✅ Drop-In✓ Em estoque
$7.12 / unidade
Ver ficha técnica →PIC16C64A-20I/L
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.1 / unidade
Ver ficha técnica →PIC16C65A-20I/L Classificações máximas e características elétricas
| Core Architecture | PIC 8-bit RISC (Harvard) |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 7 KB (4K x 14 words) |
| RAM Size | 192 bytes |
| Frequência máxima de clock | 20 MHz |
| Instruction Cycle Time | 200 ns (at 20 MHz) |
| Supply Voltage Range | 2.5 V to 6.0 V |
| Typical Supply Current | 15 uA at 5 V / 4 MHz |
| Low-Power Supply Current | 1 uA typical at 3 V / 32 kHz |
| Number of I/O Pins | 33 |
| Instruction Set Size | 35 single-word instructions |
| Faixa de temperatura de operação | -40 C to +85 C (Industrial) |
| Encapsulamento | 44-pin PLCC (16.59 x 16.59 mm) |
| Tipo de montagem | Surface Mount |
Configuração de pinos do PIC16C65A-20I/L
| Pino 1 | RA2/AN2/VREF- — PORTA bit 2 / Analog input 2 / Voltage reference negative |
| Pino 2 | RA3/AN3/VREF+ — PORTA bit 3 / Analog input 3 / Voltage reference positive |
| Pino 3 | RA4/T0CKI — PORTA bit 4 / Timer0 clock input |
| Pino 4 | RA5/SS/AN4 — PORTA bit 5 / SPI slave select / Analog input 4 |
| Pino 5 | RE0/RD/AN5 — PORTE bit 0 / Parallel slave port read / Analog input 5 |
| Pino 6 | RE1/WR/AN6 — PORTE bit 1 / Parallel slave port write / Analog input 6 |
| Pino 7 | RE2/CS/AN7 — PORTE bit 2 / Parallel slave port chip select / Analog input 7 |
| Pino 8 | OSC1/CLKIN — Oscillator crystal input / external clock input |
| Pino 9 | OSC2/CLKOUT — Oscillator crystal output / clock output |
| Pino 10 | RC0/T1OSO/T1CKI — PORTC bit 0 / Timer1 oscillator output / Timer1 clock input |
| Pino 11 | RC1/T1OSI/CCP2 — PORTC bit 1 / Timer1 oscillator input / Capture Compare PWM 2 |
| Pino 12 | RC2/CCP1 — PORTC bit 2 / Capture Compare PWM 1 |
| Pino 13 | RC3/SCK/SCL — PORTC bit 3 / SPI clock / I2C clock |
| Pino 14 | RC4/SDI/SDA — PORTC bit 4 / SPI data in / I2C data |
| Pino 15 | RC5/SDO — PORTC bit 5 / SPI data out |
| Pino 16 | RC6/TX/CK — PORTC bit 6 / USART transmit / USART clock |
| Pino 17 | RC7/RX/DT — PORTC bit 7 / USART receive / USART data |
| Pino 18 | VSS — Ground reference |
| Pino 19 | VDD — Positive supply voltage (2.5 V to 6.0 V) |
| Pino 20 | RB0/INT — PORTB bit 0 / External interrupt input |
| Pino 21 | RB1 — PORTB bit 1 |
| Pino 22 | RB2 — PORTB bit 2 |
| Pino 23 | RB3/PGM — PORTB bit 3 / Low-voltage programming input |
| Pino 24 | RB4 — PORTB bit 4 |
| Pino 25 | RB5 — PORTB bit 5 |
| Pino 26 | RB6/PGC — PORTB bit 6 / ICSP clock |
| Pino 27 | RB7/PGD — PORTB bit 7 / ICSP data |
| Pino 28 | RD0/PSP0 — PORTD bit 0 / Parallel slave port bit 0 |
| Pino 29 | RD1/PSP1 — PORTD bit 1 / Parallel slave port bit 1 |
| Pino 30 | RD2/PSP2 — PORTD bit 2 / Parallel slave port bit 2 |
| Pino 31 | RD3/PSP3 — PORTD bit 3 / Parallel slave port bit 3 |
| Pino 32 | RD4/PSP4 — PORTD bit 4 / Parallel slave port bit 4 |
| Pino 33 | RD5/PSP5 — PORTD bit 5 / Parallel slave port bit 5 |
| Pino 34 | RD6/PSP6 — PORTD bit 6 / Parallel slave port bit 6 |
| Pino 35 | RD7/PSP7 — PORTD bit 7 / Parallel slave port bit 7 |
| Pino 36 | VSS — Ground reference |
| Pino 37 | VDD — Positive supply voltage (2.5 V to 6.0 V) |
| Pino 38 | RA0/AN0 — PORTA bit 0 / Analog input 0 |
| Pino 39 | RA1/AN1 — PORTA bit 1 / Analog input 1 |
| Pino 40 | MCLR/VPP — Master clear reset / Programming voltage input |
| Pino 41 | NC — Not connected (per datasheet) |
| Pino 42 | NC — Not connected (per datasheet) |
| Pino 43 | NC — Not connected (per datasheet) |
| Pino 44 | NC — Not connected (per datasheet) |
Aplicações típicas
PIC16C65A-20I/L é adequado para 6 aplicaçãos: Industrial Automation Controllers, Motor Control Front-Ends, Embedded Instrumentation and Data Loggers, Legacy Equipment Retrofits, Automotive 12 V Bus Embedded Modules, HMI Keypad and Display Controllers.
Industrial Automation Controllers
The PIC16C65A-20I/L's industrial temperature grade (-40 C to +85 C), wide 2.5 V to 6.0 V supply range, and 33 I/O pins make it ideal for industrial automation controllers interfacing sensors, actuators, and HMI panels. With 20 MHz RISC core delivering 5 MIPS, the device handles PID loops, sequencing logic, and Modbus/serial communication within PLCs and machine controllers. The OTP memory secures proprietary control algorithms from external read-back, while 192 bytes RAM supports data buffering. Place decoupling capacitors (100 nF + 10 uF) close to VDD/VSS pins; use the USART module for RS-232/RS-485 links to remote I/O. The PLCC-44 socket allows field replacement without soldering. Compared to modern ARM Cortex-M0 MCUs, the PIC16C65A-20I/L consumes only 15 uA at 5 V / 4 MHz, extending battery-backed sensor node operation.
Recomendado
Motor Control Front-Ends
The PIC16C65A-20I/L provides capture/compare/PWM (CCP) modules and a 20 MHz instruction cycle time (200 ns) suitable for motor control front-ends driving brushed DC, stepper, or BLDC motors via external MOSFET drivers. The 33 I/O pins can drive direction/Enable lines, Hall-effect sensor inputs, and quadrature encoder feedback. With 7 KB OTP program memory, complete field-oriented control or trapezoidal commutation routines fit comfortably. The wide 2.5 V to 6.0 V supply accepts 5 V regulator rails typical of industrial 24 V bus systems. Note: PWM frequency is limited by the 8-bit timer resolution at 20 MHz - use the CCP module in PWM mode with prescaler for motor-drive switching frequencies of 10-20 kHz. Pair with IR2104 gate drivers for half-bridge control.
Recomendado
Embedded Instrumentation and Data Loggers
With 7 KB OTP program memory, 192 bytes RAM, and an integrated USART, the PIC16C65A-20I/L forms the core of embedded instrumentation such as digital panel meters, environmental monitors, and portable data loggers. The 15 uA typical supply current at 5 V / 4 MHz and 1 uA at 3 V / 32 kHz enables battery-backed operation with months of standby life. Connect external 12-bit ADC chips via SPI or I2C for precision measurement of temperature, pressure, or flow sensors. The parallel slave port allows direct interface to LCD modules or external data memory. Use the 33 I/O pins for keypad scanning, alarm outputs, and indicator LEDs. OTP memory secures calibration coefficients and proprietary measurement algorithms from reverse engineering.
Recomendado
Legacy Equipment Retrofits
The PIC16C65A-20I/L is well-suited as a drop-in replacement for obsolete PIC16C65-20/P or PIC16C65-20I/L parts in legacy industrial equipment, instrumentation, and aerospace systems where PCB redesign is not feasible. Its 44-pin PLCC footprint and pin-compatible PIC16C6x architecture allow direct socketed replacement with the latest silicon revision. The OTP memory ensures firmware compatibility with original control code, while the 20 MHz clock matches existing timing budgets. Industrial temperature grade (-40 C to +85 C) accommodates factory-floor thermal environments. Always verify peripheral pin assignments against the legacy schematic before substitution. Microchip's PIC16C65B-20I/L revision is preferred when available for errata fixes.
Recomendado
Automotive 12 V Bus Embedded Modules
With its wide 2.5 V to 6.0 V operating supply range and industrial temperature grade, the PIC16C65A-20I/L can be deployed in automotive 12 V bus embedded modules when paired with a 5 V regulator such as the LM7805. The 33 I/O pins interface with sensors, solenoids, indicator LEDs, and CAN/LIN transceivers for body control, instrument cluster peripherals, and HVAC actuators. The 20 MHz RISC core delivers deterministic 200 ns instruction cycles for time-critical signal sampling. OTP memory secures proprietary calibration data. The 44-pin PLCC package, however, is not automotive-qualified (no AEC-Q100) - this is an industrial-grade part, so automotive deployments require additional qualification. For new automotive designs, prefer PIC18F or dsPIC AEC-Q100-qualified parts.
Recomendado
HMI Keypad and Display Controllers
The PIC16C65A-20I/L drives HMI panels with 4x4 or larger keypads and character or graphic LCDs through its parallel slave port and 33 I/O pins. With 20 MHz instruction speed, matrix keypad scanning, debouncing, and character display updates occur within microseconds, leaving CPU bandwidth for application logic. Connect HD44780-based character LCDs directly via PORT B and PORT D, or interface with graphic LCDs via the parallel slave port for higher throughput. The USART enables communication with main controllers or remote terminals. OTP memory stores keypad mapping tables and UI state machines, while 192 bytes RAM buffers scanned key events. Industrial temperature grade supports factory HMI panels with extended thermal envelopes. Pair with a MAX232 for RS-232 HMI terminals.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16C65A-20I/L — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16C65B-20I/L | PIC16C66-20I/L | PIC16C67-20I/L | PIC16F877A-I/L | PIC16C64A-20I/L |
|---|---|---|---|---|---|---|
| Package | 44-pin PLCC | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same | 44-pin PLCC - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Program Memory | 7 KB OTP | 7 KB OTP | 14 KB OTP | 14 KB OTP | 14 KB Flash | 3.5 KB OTP |
| Memory Type | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM | Flash | OTP EPROM |
| RAM | 192 bytes | 192 bytes | 368 bytes | 368 bytes | 368 bytes | 128 bytes |
| Maximum Clock | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| I/O Pins | 33 | 33 | 33 | 33 | 33 | 33 |
| Temperature Grade | Industrial (-40 to +85 C) | Industrial | Industrial | Industrial | Industrial | Industrial |
Principais diferenciais
- Wide 2.5 V to 6.0 V supply range (vs PIC16F877A-I/L)
- OTP memory for code security (vs PIC16F877A-I/L)
- Ultra-low standby current (vs PIC16C64A-20I/L)
Notas de projeto
Decouple VDD/VSS pairs (pins 19/18 and 37/36) with a 100 nF ceramic capacitor placed within 5 mm of each pin pair, plus a 10 uF bulk capacitor on the main VDD rail. The PIC16C65A-20I/L has separate analog (VDD/VSS) and digital supply regions - keep analog VDD/VSS clean by routing them separately from switching digital loads. Estimated: at 20 MHz / 5 V the supply current is approximately 15-25 mA depending on peripheral activity; budget accordingly for the LDO or switching regulator upstream.
OTP memory is one-time programmable - firmware bugs cannot be corrected after programming. Use a PIC16F877A-I/L socket-compatible part for development and qualification, then move to PIC16C65A-20I/L for production once firmware is locked. Always preserve a known-good programmed unit as a reference. Verify interrupt vector placement and branch-cycle timing against the 200 ns instruction budget (branches take 400 ns) for time-critical routines.
Place the crystal or ceramic resonator within 10 mm of pins 8 (OSC1) and 9 (OSC2), with ground-plane isolation around the oscillator traces to reduce EMI. Use a MCLR pull-up (typically 10 kohm) on pin 40 to ensure clean reset behavior; the MCLR pin is internally pulled high but external pull-up is required for noisy environments. Route the parallel slave port (PORTD and pins 5/6/7 of PORTE) with matched trace lengths if used for external memory interfacing.
The 20 MHz oscillator generates harmonics up to 100+ MHz; keep clock traces short and guard with ground plane to prevent radiated EMI. Estimated: enable the watchdog timer and brown-out reset (configurable in the CONFIG word) for unattended industrial deployments. If using the ADC, ensure adequate acquisition time (minimum 20 us at 5 V) and bypass AVSS/AVDD with 100 nF + 10 uF caps. The 33 I/O pins source/sink up to 25 mA each (per pin) and 90 mA per port - observe these limits when driving LEDs directly.
Informações de conformidade
RoHS/REACH/lead-free compliance not explicitly stated in verified web data. Not AEC-Q100 qualified - this is an industrial-grade part. For automotive applications, use AEC-Q100-qualified PIC18F or dsPIC variants instead.
