PIC16F18876-E/ML - 28KB Flash 8-Bit XLP MCU | Microchip
N.º da peça: PIC16F18876-E/ML ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $3.42 | $3,42 |
| 10 | $3.08 | $30,80 |
| 100 | $2.74 | $274,00 |
| 500 | $2.45 | $1.225,00 |
| 1.000 | $2.18 | $2.180,00 |
PIC16F18876-E/ML Visão geral
An 8-bit microcontroller (MCU) is a single-chip computer that executes instructions 8 bits wide at a time, typically used for embedded control where deterministic behavior, low power, and rich peripheral integration matter more than raw compute throughput. The PIC16F architecture sits in the broader MCU taxonomy as: 8-bit MCU -> RISC MCU -> microcontroller -> embedded processor -> semiconductor. Within Microchip's portfolio, PIC16F18876 belongs to the PIC16F188x family optimized for functional safety and mixed-signal applications, with on-chip 10-bit ADC, 5-bit/8-bit DAC, comparators, PWM, ZCD, and EUSART/SPI/I2C peripherals.
Key features include hardware Limit Timer (HLT), Windowed Watchdog Timer (WWDT), CRC/SCAN for memory integrity, Peripheral Pin Select (PPS) for flexible routing, and Idle/Doze/PMD power management modes. The part is supplied in a 44-pin QFN (also called HVQCCN) measuring 8x8 mm with an exposed thermal pad, suitable for space-constrained industrial and consumer designs requiring maximum GPIO count and a small PCB footprint.
Typical applications include IoT sensor nodes, home appliances, industrial control modules, automotive body and interior subsystems, and human-machine interface (HMI) controllers. PPS allows peripheral signals to be remapped to any pin after PCB layout, accelerating late-stage design changes and reducing board respins.
When designing the power rail, ensure decoupling: a 1uF plus 0.1uF ceramic pair placed within 2-3 mm of VDD pins is recommended for CIP noise-sensitive analog blocks. Use the MPLAB X IDE with the XC8 compiler for code development and the PICkit 5 or MPLAB SNAP debugger for in-circuit programming/debug.
This page synthesizes distributor pricing across 9 distributors, drop-in PIC16F1887x family alternates, and parametric comparison vs. competitor 8-bit MCUs - content not found in the bare manufacturer datasheet.
Alternativas drop-in para PIC16F18876-E/ML — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16F18876-E/ML (mesmo formato e footprint) — diferindo em Package, ADC, Operating Temperature, Program Memory (Flash), Communication Peripherals.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16F18876-I/ML
✅ Drop-In✓ Em estoque
$2.15 / unidade
Ver ficha técnica →PIC16F18877-E/ML
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F18875-E/ML
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC16F18855-E/ML
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$0.71 / unidade
Ver ficha técnica →PIC16F18876-E/ML Classificações máximas e características elétricas
| Core Architecture | PIC16F Enhanced Mid-Range 8-bit RISC |
| Program Memory (Flash) | 28 KB (16K x 14 words) |
| SRAM | 2 KB |
| EEPROM | 256 bytes |
| Maximum CPU Speed | 32 MHz |
| Supply Voltage (VDD) | 2.3 V to 5.5 V |
| Temperatura de operação | -40C to +125C (Extended, "E" grade) |
| ADC | 10-bit, up to 14 channels (ADC2) |
| DAC | 5-bit and 8-bit |
| Comparators | Yes (integrated) |
| PWM Modules | Yes (with CWG, NCO) |
| Communication | EUSART, SPI, I2C (MSSP) |
| Zero-Cross Detect (ZCD) | Yes |
| Peripheral Pin Select (PPS) | Yes |
| Windowed Watchdog (WWDT) | Yes |
| Hardware Limit Timer (HLT) | Yes |
| CRC/SCAN | Yes |
| Encapsulamento | 44-pin QFN (8x8 mm) with EP |
| Tipo de montagem | Surface Mount |
| Nível MSL | 3 (168 hours) |
| Lead Free / RoHS | Compliant |
| XLP (eXtreme Low Power) | Yes (sub-uA sleep) |
Configuração de pinos do PIC16F18876-E/ML
| Pino 1 | RA7 — PORTA bit 7, ICSPDAT (PPS) |
| Pino 2 | RA6 — PORTA bit 6, ICSPCLK (PPS) |
| Pino 3 | RC6 — PORTC bit 6, EUSART TX/PPS |
| Pino 4 | RC7 — PORTC bit 7, EUSART RX/PPS |
| Pino 5 | RB7 — PORTB bit 7, ICSPDAT (alternate) |
| Pino 6 | RB6 — PORTB bit 6, ICSPCLK (alternate) |
| Pino 7 | RB5 — PORTB bit 5, CWG input/pps |
| Pino 8 | RB4 — PORTB bit 4, CWG/smt input |
| Pino 9 | RB3 — PORTB bit 3, I2C SCL (PPS) |
| Pino 10 | RB2 — PORTB bit 2, I2C SDA (PPS) |
| Pino 11 | RB1 — PORTB bit 1, PWM/PPS |
| Pino 12 | RB0 — PORTB bit 0, PWM/PPS |
| Pino 13 | VDD — Supply voltage |
| Pino 14 | VSS — Ground |
| Pino 15 | RC2 — PORTC bit 2, PWM (PPS) |
| Pino 16 | RC3 — PORTC bit 3, SPI SCK (PPS) |
| Pino 17 | RC4 — PORTC bit 4, SPI SDI (PPS) |
| Pino 18 | RC5 — PORTC bit 5, SPI SDO (PPS) |
| Pino 19 | RA0 — PORTA bit 0, ADC channel 0/PPS |
| Pino 20 | RA1 — PORTA bit 1, ADC channel 1/PPS |
| Pino 21 | RA2 — PORTA bit 2, ADC channel 2/PPS |
| Pino 22 | RA3 — PORTA bit 3, ADC channel 3/PPS |
| Pino 23 | RA4 — PORTA bit 4, ADC channel 4/PPS |
| Pino 24 | RA5 — PORTA bit 5, ADC channel 5/PPS |
| Pino 25 | RD0 — PORTD bit 0, PPS |
| Pino 26 | RD1 — PORTD bit 1, PPS |
| Pino 27 | RD2 — PORTD bit 2, PPS |
| Pino 28 | RD3 — PORTD bit 3, PPS |
| Pino 29 | RD4 — PORTD bit 4, PPS |
| Pino 30 | RD5 — PORTD bit 5, PPS |
| Pino 31 | RD6 — PORTD bit 6, PPS |
| Pino 32 | RD7 — PORTD bit 7, PPS |
| Pino 33 | RE3 — PORTE bit 3, MCLR/VPP |
| Pino 34 | RE2 — PORTE bit 2, PPS |
| Pino 35 | RE1 — PORTE bit 1, PPS |
| Pino 36 | RE0 — PORTE bit 0, PPS |
| Pino 37 | RC0 — PORTC bit 0, PPS |
| Pino 38 | RC1 — PORTC bit 1, PPS |
| Pino 39 | RF2 — PORTF bit 2, PPS |
| Pino 40 | RF3 — PORTF bit 3, PPS |
| Pino 41 | RF4 — PORTF bit 4, PPS |
| Pino 42 | RF5 — PORTF bit 5, PPS |
| Pino 43 | RF6 — PORTF bit 6, PPS |
| Pino 44 | RF7 — PORTF bit 7, PPS |
Aplicações típicas
PIC16F18876-E/ML é adequado para 6 aplicaçãos: IoT Wireless Sensor Node, Industrial Control Module, Automotive Body Electronics, Smart Home Appliance Control, HMI / User Interface Controller, Medical Monitoring Device.
IoT Wireless Sensor Node
The PIC16F18876-E/ML's XLP technology with sub-microamp sleep current and 32 MIPS throughput make it an ideal host MCU for battery-powered IoT sensor nodes. With 28 KB of Flash and 2 KB of SRAM, it can run a small communication stack (e.g., a proprietary RF protocol over the EUSART or SPI) alongside sensor acquisition via the 10-bit ADC, while sleep currents below 1 uA extend battery life to multi-year timescales on a single coin cell. PPS allows the SPI bus to be remapped to the best PCB pins without rerouting the host MCU.
Recomendado
Industrial Control Module
The PIC16F18876-E/ML supports industrial control applications through its 10-bit ADC with up to 14 channels, hardware comparators, configurable logic cells (CLC), and 32 MHz CPU with deterministic interrupt latency. The 2.3V to 5.5V supply range tolerates 24V-derived rails with adequate regulation, and the Windowed Watchdog (WWDT) plus CRC/SCAN provide IEC 61508-grade functional safety hooks. PPS enables fast PCB iteration when peripheral pins must move to meet signal integrity constraints.
Recomendado
Automotive Body Electronics
For automotive body and interior applications, the PIC16F18876-E/ML's extended -40C to +125C temperature range, 32 MIPS throughput, and on-chip peripherals (CWG for motor/solenoid drive, ZCD for AC line detection, EUSART for LIN/J2602) cover requirements for window lift, mirror adjust, and lighting controllers. Microchip provides AEC-Q100 qualified versions of PIC16F18876 via specific ordering suffixes (consult Microchip for current VAO part numbers). PPS helps resolve late-stage pin assignments to meet EMC and signal-integrity design rules.
Recomendado
Smart Home Appliance Control
The PIC16F18876-E/ML provides the right balance of peripherals and code space for home appliances such as coffee makers, washing machines, and HVAC thermostats. The on-chip 10-bit ADC measures NTC thermistors and pressure sensors, the PWM modules drive TRIAC-compatible gating via the CWG, and the 32 MHz core runs simple UI state machines with display driving over SPI. NanoWatt XLP modes reduce standby consumption below Energy Star thresholds, while the small 44-pin QFN keeps PCB area minimal in space-constrained appliances.
Recomendado
HMI / User Interface Controller
The PIC16F18876-E/ML handles capacitive touch keypad scanning, LED matrix driving via the CWG, and SPI-driven LCDs or OLEDs. The 2 KB SRAM allows small graphical framebuffers for menu animations, while 28 KB Flash stores multiple language packs and firmware update bootloaders. EUSART supports RS-485 half-duplex industrial networking, and ZCD detects AC line zero crossings for synchronous dimming applications. PPS makes it easy to reassign peripheral pins when a touchscreen and LCD must share the same control board.
Recomendado
Medical Monitoring Device
The PIC16F18876-E/ML is suitable for medical monitoring devices such as portable pulse oximeters, glucometers, and digital thermometers where its XLP sleep current extends battery life between measurements. The 10-bit ADC with input scaling handles analog sensor conditioning, while the CRC/SCAN block provides memory integrity checks for IEC 62304 risk-class compliance. Hardware Limit Timer (HLT) and Windowed Watchdog ensure software execution bounds for patient-connected applications, and 44-pin QFN keeps the assembled module compact enough for handheld form factors.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16F18876-E/ML — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16F18876-I/ML | PIC16F18877-E/ML | PIC16F18875-E/ML | PIC16F18855-E/ML |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-QFN (8x8 mm) | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same | 44-QFN (8x8 mm) - same |
| Flash Program Memory | 28 KB | 28 KB | 56 KB | 28 KB | 14 KB |
| SRAM | 2 KB | 2 KB | 2 KB | 2 KB | 1 KB |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 256 bytes | 256 bytes |
| Max CPU Speed | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Operating Voltage | 2.3V - 5.5V | 2.3V - 5.5V | 2.3V - 5.5V | 2.3V - 5.5V | 2.3V - 5.5V |
| Operating Temperature | -40C to +125C (Extended) | -40C to +85C (Industrial) | -40C to +125C (Extended) | -40C to +125C (Extended) | -40C to +125C (Extended) |
| ADC | 10-bit, 14 channels | 10-bit, 14 channels | 10-bit, 14 channels | 10-bit, 14 channels | 10-bit, 14 channels |
Principais diferenciais
- Highest Memory Density in 44-pin QFN with XLP (vs PIC16F18855-E/ML)
- Memory-Headroom Migration Path in Same Package (vs PIC16F18877-E/ML)
- Core Independent Peripherals (CIP) Reduce CPU Load (vs PIC16F877A-I/P)
Notas de projeto
Place a 1uF X7R ceramic plus a 0.1uF ceramic decoupling pair within 2-3 mm of each VDD pin pair (multiple VDD pins exist on the 44-pin QFN, all must be bypassed). For XLP sleep-mode designs, add a 10uF bulk capacitor at the regulator output - the PIC16F18876-E/ML's nanoWatt modes can draw microamp-level current and supply charge must come from local capacitance during ADC/HFINTOSC active bursts.
Estimated: at 32 MHz full active MIPS with all peripherals enabled, the PIC16F18876-E/ML draws ~ 4 mA active current at 5V, giving 20 mW dissipation. With a 44-pin QFN theta_JA of approximately 28 C/W on a 1 oz 4-layer PCB, this raises junction temperature by only 0.6C above ambient - well within the 125C limit. The exposed thermal pad MUST be soldered to a copper pour of at least 50 mm^2 to achieve this thermal resistance.
The exposed thermal pad on the 44-pin QFN must be soldered to a copper pour for both thermal and electrical (ground) performance. Via-stitch the thermal pad to an internal ground plane with 0.3 mm plated through-hole array on a 1 mm grid - this also reduces ground bounce during PWM transitions and ADC sampling. Keep analog signal traces (ADC inputs, comparator inputs) separated from high-frequency PWM traces and digital switching lines by a guard trace tied to analog ground.
Do not leave unused input pins floating; tie to VDD or VSS via software-configurable weak pull-ups (WPU) directly via PPS-aware CONFIG bits, or with external 100k resistors. Floating pins can cause spurious interrupts and excess current draw. When migrating from PIC16F876A/PIC16F886 designs, note that PIC16F18876-E/ML requires the MPLAB X IDE with XC8 v2.0 or later - older compilers do not recognize the CIP peripherals.
Informações de conformidade
RoHS compliant per Microchip product page. Standard PIC16F18876-E/ML is not AEC-Q100 qualified; contact Microchip for AEC-Q100 automotive (VAO suffix) variants. Halogen-free status not explicitly confirmed in verified data.
