PIC16F884-E/ML - 8-Bit 20MHz 7KB Flash MCU 44-QFN | Microchip
N.º da peça: PIC16F884-E/ML ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $3.92 | $3,92 |
| 10 | $3.53 | $35,30 |
| 100 | $3.13 | $313,00 |
| 500 | $2.74 | $1.370,00 |
| 1.000 | $2.43 | $2.430,00 |
PIC16F884-E/ML Visão geral
A microcontroller (MCU) is a single-chip computer containing a CPU, memory (Flash/RAM/EEPROM), and programmable peripherals. The PIC16F family is Microchip's mid-range 8-bit architecture offering a balance of code density, peripheral mix, and low power via nanoWatt technology. MCUs sit at the lowest tier of the embedded computing hierarchy: transistor -> logic gate -> CPU core -> microcontroller -> embedded system -> IoT/edge device. The PIC16F884 belongs to the 28/40/44-pin enhanced flash-based 8-bit CMOS family with nanowatt technology.
Key features include self-programmability for bootloader-style field updates, 10-bit A/D converter with up to 14 channels, enhanced capture/compare/PWM (ECCP) modules, multiple timers (Timer0/1/2), AUSART serial communication, MSSP for SPI/I2C, and a nanoWatt power management unit with multiple idle/sleep modes that drop quiescent current to the microamp range. The 44-QFN package exposes 36 I/O pins versus 22 in the smaller 28-pin variants, enabling direct drive of larger displays or sensor arrays.
The architecture uses a 14-bit instruction word and Harvard bus (separate program/data paths), giving deterministic single-cycle execution for most instructions except branches. The 20 MHz oscillator yields a 200 ns instruction cycle, sufficient for real-time control loops in motor, lighting, and consumer appliance subsystems. Brown-out reset (BOR), power-on reset (POR), and watchdog timer (WDT) with on-chip oscillator form the standard reliability suite.
Typical applications include home appliances (washing machines, microwave ovens, induction cooktops), industrial control panels, automotive body modules, lighting ballasts and dimmers, remote controls, low-end toys, instrumentation, and sensor hubs. The peripheral mix (ADC, PWM, UART, I2C/SPI) is well-suited to multi-signal acquisition systems.
When designing with this device, allocate the 35 instruction set carefully because 7 KB Flash is constrained for modern protocol stacks (e.g., full Modbus RTU). The 'E' suffix denotes the extended industrial temperature grade (-40C to +125C). Decoupling capacitors must be placed within 5 mm of the QFN ground paddle for thermal and noise integrity.
This page synthesizes distributor pricing, drop-in QFN-44 alternatives, and practical design notes not found in the manufacturer datasheet.
Alternativas drop-in para PIC16F884-E/ML — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC16F884-E/ML (mesmo formato e footprint) — diferindo em Operating Temperature, Package, Core Architecture, Timers, I/O Pins.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC16F884-I/ML
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F884T-I/ML
✅ Drop-In✓ Em estoque
$3.18 / unidade
Ver ficha técnica →PIC16F882-I/ML
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC16F883-I/SS
✅ Drop-In✓ Em estoque
$1.74 / unidade
Ver ficha técnica →PIC16F887-I/ML
✅ Drop-In✓ Em estoque
$3.16 / unidade
Ver ficha técnica →PIC16F886-E/ML
✅ Drop-In✓ Em estoque
$1.71 / unidade
Ver ficha técnica →PIC16F884-E/ML Classificações máximas e características elétricas
| Core Architecture | PIC 8-bit, Harvard bus, 14-bit instruction word |
| CPU Frequency | 20 MHz maximum |
| Instruction Cycle | 200 ns at 20 MHz |
| Program Memory (Flash) | 7 KB (4K x 14 words) |
| Data EEPROM | 256 bytes |
| Data RAM | 368 bytes |
| I/O Pins | 36 (multiplexed with peripherals) |
| A/D Converter | 10-bit, up to 14 channels |
| Timers | Timer0, Timer1, Timer2 |
| CCP/Enhanced CCP | Yes (ECCP) |
| Serial Interfaces | AUSART (UART), MSSP (SPI/I2C) |
| Operating Voltage (VDD) | 2.0 V to 5.5 V |
| Power-Saving Modes | nanoWatt (Idle, Sleep) |
| Temperatura de operação | -40C to +125C (E suffix, industrial extended) |
| Encapsulamento | 44-pin QFN (8x8 mm) with exposed pad |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
| Self-Programming | Yes (in-application via Flash) |
| Brown-Out Reset | Yes (BOR + PWRT) |
| Watchdog Timer | Yes (WDT with dedicated oscillator) |
Configuração de pinos do PIC16F884-E/ML
| Pino 1 | RA6/OSC2/CLKO — OSC2: crystal/oscillator output; CLKO: clock output; RA6: digital I/O |
| Pino 2 | RA7/OSC1/CLKI — OSC1: crystal/oscillator input; CLKI: clock input; RA7: digital I/O |
| Pino 3 | RE3/MCLR/VPP — Master Clear (reset) input / programming voltage; RE3: digital input only |
| Pino 4 | RA0/AN0/ULPWU/C12IN0- — RA0: digital I/O; AN0: ADC channel 0; ULPWU: ultra-low-power wake-up |
| Pino 5 | RA1/AN1/C12IN1- — RA1: digital I/O; AN1: ADC channel 1 |
| Pino 6 | RA2/AN2/VREF-/CVREF/C2IN+ — RA2: digital I/O; AN2: ADC; VREF-: negative ADC reference |
| Pino 7 | RA3/AN3/VREF+/C1IN+ — RA3: digital I/O; AN3: ADC; VREF+: positive ADC reference |
| Pino 8 | RA4/T0CKI/C1OUT — RA4: digital I/O; T0CKI: Timer0 clock input; C1OUT: comparator 1 output |
| Pino 9 | RA5/AN4/SS/C2OUT — RA5: digital I/O; AN4: ADC; SS: SPI slave select |
| Pino 10 | VSS — Ground reference |
| Pino 11 | VDD — Positive supply voltage (2.0 V to 5.5 V) |
| Pino 12 | RB0/AN12/INT — RB0: digital I/O; AN12: ADC; INT: external interrupt |
| Pino 13 | RB1/AN10/C12IN3-/P1C — RB1: digital I/O; AN10: ADC; P1C: PWM output |
| Pino 14 | RB2/AN8/P1B — RB2: digital I/O; AN8: ADC; P1B: PWM output |
| Pino 15 | RB3/AN9/PGM/C12IN2- — RB3: digital I/O; AN9: ADC; PGM: LVP programming enable |
| Pino 16 | RB4/AN11/P1D — RB4: digital I/O; AN11: ADC; P1D: PWM output |
| Pino 17 | RB5/AN13/T1G/P2B — RB5: digital I/O; AN13: ADC; T1G: Timer1 gate; P2B: PWM |
| Pino 18 | RB6/PGC/T1OSI/T1CKI — RB6: digital I/O; PGC: ICSP clock; T1OSI: Timer1 osc input |
| Pino 19 | RB7/PGD/T1OSO/CCP4 — RB7: digital I/O; PGD: ICSP data; CCP4: capture/compare/PWM |
| Pino 20 | VSS — Ground reference (second VSS pin) |
| Pino 21 | VDD — Positive supply (second VDD pin) |
| Pino 22 | RC0/T1OSO/T13CKI — RC0: digital I/O; T1OSO: Timer1 oscillator output |
| Pino 23 | RC1/T1OSI/CCP2 — RC1: digital I/O; T1OSI: Timer1 oscillator input; CCP2: PWM |
| Pino 24 | RC2/CCP1/P2A — RC2: digital I/O; CCP1: capture/compare/PWM 1; P2A: PWM |
| Pino 25 | RC3/SCK/SCL — RC3: digital I/O; SCK/SCL: SPI/I2C clock |
| Pino 26 | RC4/SDI/SDA — RC4: digital I/O; SDI/SDA: SPI data in / I2C data |
| Pino 27 | RC5/SDO — RC5: digital I/O; SDO: SPI data out |
| Pino 28 | RC6/TX/CK — RC6: digital I/O; TX: UART transmit; CK: UART clock |
| Pino 29 | RC7/RX/DT — RC7: digital I/O; RX: UART receive; DT: UART data |
| Pino 30 | RD0 — RD0: digital I/O (Port D) |
| Pino 31 | RD1 — RD1: digital I/O (Port D) |
| Pino 32 | RD2 — RD2: digital I/O (Port D) |
| Pino 33 | RD3 — RD3: digital I/O (Port D) |
| Pino 34 | RD4 — RD4: digital I/O (Port D) |
| Pino 35 | RD5/P1B — RD5: digital I/O; P1B: PWM output (Enhanced CCP) |
| Pino 36 | RD6/P1C — RD6: digital I/O; P1C: PWM output |
| Pino 37 | RD7/P1D — RD7: digital I/O; P1D: PWM output |
| Pino 38 | VSS — Ground reference (third VSS pin) |
| Pino 39 | VDD — Positive supply (third VDD pin) |
| Pino 40 | RE0/RD — RE0: digital I/O; RD: parallel port read strobe (PSP) |
| Pino 41 | RE1/WR — RE1: digital I/O; WR: parallel port write strobe (PSP) |
| Pino 42 | RE2/CS — RE2: digital I/O; CS: parallel port chip select (PSP) |
| Pino 43 | AVSS — Analog ground reference (tie to VSS) |
| Pino 44 | AVDD — Analog positive supply (tie to VDD) |
Aplicações típicas
PIC16F884-E/ML é adequado para 6 aplicaçãos: Home Appliance Control, Industrial Sensor Hub, LED Lighting Controller, Automotive Body Module, Remote Control and HMI, Consumer Electronics and Toys.
Home Appliance Control
The PIC16F884-E/ML fits washing-machine, microwave, and induction-cooktop control boards because its 36 I/O pins directly drive 7-segment displays, keypad matrices, relay coils, and triac zero-cross circuits. The 7 KB Flash holds full state-machine code including sensor calibration, fault handling, and BLE/UART modules. The 10-bit ADC with 14 channels reads temperature, humidity, and load-current feedback; the ECCP module generates PWM for motor speed and inverter control. nanoWatt sleep modes reduce standby to microamp range for energy-star compliance.
Recomendado
Industrial Sensor Hub
The PIC16F884-E/ML suits multi-sensor industrial nodes because its AUSART plus MSSP (SPI/I2C) bus controllers interface simultaneously with digital temperature sensors, pressure transducers, and accelerometers. The 10-bit ADC digitizes analog channels from 4-20 mA loops or thermistor bridges. With -40C to +125C operation, the E-grade survives factory-floor thermal stress. Self-programming Flash allows secure over-the-air firmware updates via Modbus RTU on RS-485. The 256-byte EEPROM stores calibration constants and node IDs without external storage.
Recomendado
LED Lighting Controller
The PIC16F884-E/ML drives LED ballasts and dimmers via its ECCP PWM module, which generates frequency-adjustable, duty-cycle-controlled PWM with hardware dead-band control for half-bridge drivers. The 36 I/O pins drive multiple channels of constant-current LED drivers (e.g., TLC5940) in SPI daisy-chain or directly switch MOSFETs with PWM. The 10-bit ADC reads ambient light sensors for closed-loop dimming. Low-power nanoWatt modes enable battery-powered wireless lighting controls.
Recomendado
Automotive Body Module
The PIC16F884-E/ML powers body-control modules for door locks, window lifters, mirror adjusters, and interior lighting. Its -40C to +125C extended temperature range meets AEC-Q100 Grade 1 zones (cabin/body), and its ECCP with hardware PWM simplifies driving brushed DC motors via H-bridges. LIN bus connectivity is implemented via AUSART plus an external LIN transceiver. The 256-byte EEPROM retains learned positions and fault logs even when battery is disconnected.
Recomendado
Remote Control and HMI
The PIC16F884-E/ML is well-suited to IR/RF remote controls and small human-machine interfaces because its 36 I/O pins scan 6x6 keypad matrices and drive LCDs or OLEDs via SPI. The AUSART links to RF transceivers (e.g., nRF24L01) for wireless control, while nanoWatt sleep modes extend battery life to years on coin cells. The 7 KB Flash holds complex gesture-recognition or voice-command firmware with on-the-fly updates via bootloader.
Recomendado
Consumer Electronics and Toys
The PIC16F884-E/ML drives cost-sensitive consumer devices, electronic toys, and educational kits because its sub-$3 unit price at 1k quantities keeps BOM costs low while delivering 5 MIPS performance. The 7 KB Flash supports interactive sound playback, multi-channel servo control for robotics, and I2C/SPI sensor expansion. The 36 I/O pins drive RGB LED matrices, haptic feedback motors, and small TFT displays. Self-programming Flash enables end-user firmware updates via USB/UART bridges.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC16F884-E/ML — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC16F884-I/ML | PIC16F884T-I/ML | PIC16F882-I/ML | PIC16F883-I/SS | PIC16F887-I/ML | PIC16F886-E/ML |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-QFN (8x8) | 44-QFN (8x8) - same | 44-QFN (8x8) - same | 44-QFN (8x8) - same | 44-QFN (8x8) - same | 44-QFN (8x8) - same | 44-QFN (8x8) - same |
| Flash Memory | 7 KB | 7 KB | 7 KB | 3.5 KB | 4 KB | 14 KB | 14 KB |
| Data RAM | 368 bytes | 368 bytes | 368 bytes | 128 bytes | 192 bytes | 368 bytes | 368 bytes |
| EEPROM | 256 bytes | 256 bytes | 256 bytes | 128 bytes | 256 bytes | 256 bytes | 256 bytes |
| I/O Pins | 36 | 36 | 36 | 24 | 24-36 | 36 | 28 |
| CPU Frequency | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Temperature Grade | -40C to +125C (E) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) | -40C to +85C (I) | -40C to +125C (E) |
| Price (qty 1, USD) | 3.92 | approx 3.50 | approx 3.50 | approx 3.00 | approx 3.20 | approx 4.20 | approx 4.10 |
Principais diferenciais
- Highest Flash memory in mid-range PIC16F88x family with E temperature grade (vs PIC16F883-I/SS)
- Most I/O pins available in 44-QFN package for direct sensor/relay drive (vs PIC16F882-I/ML)
- Lower price than higher-memory siblings while keeping same 44-QFN footprint (vs PIC16F887-I/ML)
- E temperature grade in 44-QFN package with 36 I/O and ECCP (vs PIC16F886-E/ML)
Notas de projeto
The 44-QFN (8x8 mm) package has a central exposed thermal pad (EP) on its underside that must be soldered to a PCB land of at least the same dimensions and tied to a clean ground plane. Use a via array (typically 9 to 25 vias, 0.3 mm drill, 0.5 mm pitch) under the EP to carry heat into inner ground planes and reduce junction-to-ambient thermal resistance. Missing or incomplete EP soldering raises junction temperature by 30C or more, potentially causing thermal-shutdown-like behavior under high CPU load.
Place a 100 nF decoupling capacitor within 3 mm of each VDD pin (the PIC16F884 has three VDD pins at 11, 21, 39) and a single 10 uF bulk capacitor near the package. The AVDD and AVSS pins (44 and 43) supply the ADC core - isolate AVDD with a ferrite bead from VDD, and decouple AVSS to AGND with 100 nF + 10 uF. Failure to isolate analog supply increases ADC noise by 2-4 LSB at 10-bit resolution, degrading sensor readings.
MCLR (pin 3) is a mandatory reset input. Tie it to VDD through a 10 kohm pull-up resistor and add a 100 nF capacitor to ground for noise immunity. Floating MCLR causes random resets in electrically noisy environments (relay boards, motor drives). When using the internal oscillator instead of an external crystal, configure the CONFIG register FOSC bits correctly and disconnect OSC1/OSC2 - otherwise the unconnected oscillator pins pick up EMI and destabilize the system clock.
The MSSP peripheral for I2C communication requires external pull-up resistors on SDA/SCL lines (typically 4.7 kohm at 100 kHz, 2.2 kohm at 400 kHz). The PIC16F884's I/O pins are not true open-drain - configure them as open-drain via the ODCON register when using I2C mode. For SPI, keep trace lengths under 50 mm and route the SCK signal away from analog inputs to avoid clock-feedthrough into ADC readings.
Informações de conformidade
RoHS/REACH compliant per Microchip product page. Not AEC-Q100 qualified, but the -40C to +125C extended temperature range supports many AEC-Q100 Grade 0/1 use cases indirectly. Microchip maintains QS-9000 quality certification for the PIC16F family.
