PIC17C43T-25I/PQ - 8-bit 25MHz OTP MCU 8KB EPROM | Microchip
N.º da peça: PIC17C43T-25I/PQ ✗ Fim de vida| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $22.5 | $22,50 |
| 10 | $20.25 | $202,50 |
| 100 | $18 | $1.800,00 |
| 500 | $15.75 | $7.875,00 |
| 1.000 | $13.5 | $13.500,00 |
PIC17C43T-25I/PQ Visão geral
An MCU (microcontroller) is a single-chip computer that combines a CPU core, program and data memory, peripherals, and I/O on one die. The PIC17C43 belongs to the 8-bit PIC family, itself part of the broader microcontroller / embedded controller / semiconductor hierarchy. Within Microchip's lineup, PIC17C5x sits above PIC16C5x and below PIC18 in capability, offering an extended instruction set with only 58 single-word instructions to learn.
Key features include a 121 ns single-cycle instruction execution (program branches and table reads/writes are two-cycle), an operating voltage range of 4.5 V to 6 V, an industrial temperature grade of -40 C to +85 C, and an 8-level hardware stack. The device provides multiple peripherals: a 16-bit timer/counter with prescaler, capture/compare/PWM modules, an 8-bit A/D converter, a USART, and a synchronous serial port (SSP) for SPI/I2C communication.
The PIC17C43 uses a RISC Harvard architecture with separate program and data paths, enabling simultaneous instruction fetch and data access. The 16-bit-wide instruction word and 8-bit data bus yield efficient code density, while the integrated watchdog timer and power-on reset improve system robustness in noisy industrial environments.
Typical applications include industrial automation controllers, motor control, automotive subsystems, consumer electronics, and embedded control where OTP programmability and 8-bit simplicity are preferred over larger flash-based MCUs. Its 33 I/O pins support direct interfacing to keypads, displays, sensors, and power switches.
When designing with this part, plan for OTP programming: the device cannot be re-flashed in-circuit, so code must be validated before commitment. An erasable CERDIP variant (JW package) exists for development. Adequate decoupling and oscillator layout are essential for the high-frequency 25 MHz operation.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para PIC17C43T-25I/PQ — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC17C43T-25I/PQ (mesmo formato e footprint) — diferindo em Package, Program Memory Size, Operating Temperature Range, Mounting Type, Program Memory Type.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC17C43T-25/PQ
✅ Drop-In✓ Em estoque
$8.1 / unidade
Ver ficha técnica →PIC17C43-16I/PQ
✅ Drop-In✓ Em estoque
$4.82 / unidade
Ver ficha técnica →PIC17C43-16E/P
✅ Drop-In✓ Em estoque
$8.4 / unidade
Ver ficha técnica →PIC17C42A-25/PT
✅ Drop-In✓ Em estoque
$5.55 / unidade
Ver ficha técnica →PIC17C43T-25E/PT
✅ Drop-In✓ Em estoque
$10.65 / unidade
Ver ficha técnica →PIC17CR43T-25I/PQ
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC17C43T-25I/PQ Classificações máximas e características elétricas
| Core Architecture | PIC 8-bit RISC |
| Family | PIC17C |
| Program Memory Type | OTP EPROM |
| Program Memory Size | 8 KB (4K x 16) |
| Data RAM | 454 bytes |
| Frequência máxima de clock | 25 MHz |
| Instruction Cycle Time | 121 ns (single cycle) |
| Throughput | 8.25 MIPS |
| Supply Voltage (Vcc) | 4.5 V to 6 V |
| I/O Pins | 33 |
| Timers | 16-bit timer/counter with prescaler |
| A/D Converter | 8-bit, multi-channel |
| Communication Peripherals | USART, SSP (SPI/I2C) |
| Faixa de temperatura de operação | -40 C to +85 C (Industrial) |
| Encapsulamento | 44-MQFP (PQ, 10x10 mm) |
| Tipo de montagem | Surface Mount |
| Instruction Set | 58 single-word instructions |
| Hardware Stack | 8-level |
| Watchdog Timer | Yes |
| Status RoHS | unknown |
Configuração de pinos do PIC17C43T-25I/PQ
| Pino 1 | MCLR — Master Clear (reset) input, active low |
| Pino 2 | RA0 — PORTA bit 0 (digital I/O or analog input) |
| Pino 3 | RA1 — PORTA bit 1 (digital I/O or analog input) |
| Pino 4 | RA2 — PORTA bit 2 (digital I/O or analog input) |
| Pino 5 | RA3 — PORTA bit 3 (digital I/O or analog input) |
| Pino 6 | RA4 — PORTA bit 4 (digital I/O) |
| Pino 7 | RA5 — PORTA bit 5 (digital I/O) |
| Pino 8 | RE0 — PORTE bit 0 (digital I/O or analog input) |
| Pino 9 | RE1 — PORTE bit 1 (digital I/O or analog input) |
| Pino 10 | RE2 — PORTE bit 2 (digital I/O or analog input) |
| Pino 11 | Vdd — Positive supply voltage (4.5V-6V) |
| Pino 12 | Vss — Ground |
| Pino 13 | OSC1 — Oscillator input (crystal or external clock) |
| Pino 14 | OSC2 — Oscillator output (crystal) |
| Pino 15 | RC0 — PORTC bit 0 (digital I/O or USART TX/CK) |
| Pino 16 | RC1 — PORTC bit 1 (digital I/O or USART RX/DT) |
| Pino 17 | RC2 — PORTC bit 2 (digital I/O or CCP1) |
| Pino 18 | RC3 — PORTC bit 3 (digital I/O or SSP SCL/SCLK) |
| Pino 19 | RD0 — PORTD bit 0 (digital I/O) |
| Pino 20 | RD1 — PORTD bit 1 (digital I/O) |
| Pino 21 | RD2 — PORTD bit 2 (digital I/O) |
| Pino 22 | RD3 — PORTD bit 3 (digital I/O) |
| Pino 23 | RC4 — PORTC bit 4 (digital I/O or SSP SDA/SDI) |
| Pino 24 | RC5 — PORTC bit 5 (digital I/O or SSP SDO) |
| Pino 25 | RC6 — PORTC bit 6 (digital I/O) |
| Pino 26 | RC7 — PORTC bit 7 (digital I/O) |
| Pino 27 | RD4 — PORTD bit 4 (digital I/O) |
| Pino 28 | RD5 — PORTD bit 5 (digital I/O) |
| Pino 29 | RD6 — PORTD bit 6 (digital I/O) |
| Pino 30 | RD7 — PORTD bit 7 (digital I/O) |
| Pino 31 | Vss — Ground |
| Pino 32 | Vdd — Positive supply voltage (4.5V-6V) |
| Pino 33 | RB0 — PORTB bit 0 (digital I/O with interrupt-on-change) |
| Pino 34 | RB1 — PORTB bit 1 (digital I/O with interrupt-on-change) |
| Pino 35 | RB2 — PORTB bit 2 (digital I/O with interrupt-on-change) |
| Pino 36 | RB3 — PORTB bit 3 (digital I/O with interrupt-on-change) |
| Pino 37 | RB4 — PORTB bit 4 (digital I/O with interrupt-on-change) |
| Pino 38 | RB5 — PORTB bit 5 (digital I/O with interrupt-on-change) |
| Pino 39 | RB6 — PORTB bit 6 (digital I/O with interrupt-on-change) |
| Pino 40 | RB7 — PORTB bit 7 (digital I/O with interrupt-on-change) |
| Pino 41 | NC — Not connected |
| Pino 42 | NC — Not connected |
| Pino 43 | NC — Not connected |
| Pino 44 | NC — Not connected |
Aplicações típicas
PIC17C43T-25I/PQ é adequado para 6 aplicaçãos: Industrial Automation Controllers, Motor Control and PWM Drive, Automotive Subsystem Controllers, Consumer Electronics User Interfaces, Smart Sensor and Instrumentation Hubs, Embedded Control and Educational Platforms.
Industrial Automation Controllers
The PIC17C43T-25I/PQ suits industrial PLC and controller boards where deterministic 8-bit performance and rugged 5 V operation are required. Its 25 MHz clock yields 121 ns instruction execution for fast scan times in ladder-logic emulation, while the 33 I/O pins drive relays, opto-isolators, and indicator LEDs directly. Industrial -40 to +85 C operation tolerates factory-floor thermal stress, and 454 bytes RAM support small protocol stacks. The OTP EPROM holds verified control firmware without in-field reprogrammability risk.
Recomendado
Motor Control and PWM Drive
The PIC17C43T-25I/PQ drives DC and stepper motors via its Capture/Compare/PWM (CCP) module and 16-bit timer, generating precision PWM up to 25 MHz timer tick. Its 8-bit ADC samples current and back-EMF feedback for closed-loop speed control, while 33 I/O lines connect to H-bridge drivers and encoder inputs. Industrial temperature grade and 5 V tolerance suit harsh motor enclosures. Engineers can implement trapezoidal commutation in software, leveraging the 121 ns instruction cycle for low-latency control loops.
Recomendado
Automotive Subsystem Controllers
The PIC17C43T-25I/PQ powers automotive body and chassis subsystems such as lighting controllers, HVAC flaps, and accessory multiplexers, leveraging its wide 5 V tolerance and 33 digital I/O. The integrated USART and SSP support LIN-style or SPI communication with BCM/ECU masters, while the 8-bit ADC reads thermistor and position sensors. Although not AEC-Q100 qualified, the industrial temperature grade meets many interior cabin requirements. Its OTP memory locks calibration constants, preventing end-user modification.
Recomendado
Consumer Electronics User Interfaces
The PIC17C43T-25I/PQ implements consumer user-interface controllers for appliances, toys, and small appliances that need 33 I/O to drive keypads, 7-segment displays, and LED indicators. The 8 KB OTP holds graphical menu logic and timing routines, and the 8-bit ADC reads touch or potentiometer inputs. Industrial temperature tolerance supports kitchen and laundry environments where heat and humidity challenge commercial-grade parts. Program memory density allows full keypad scanning plus sensor fusion in firmware.
Recomendado
Smart Sensor and Instrumentation Hubs
The PIC17C43T-25I/PQ serves as a sensor hub in instrumentation, multiplexing analog inputs through its 8-bit ADC and forwarding digital data via USART or SPI to a host processor. Its 454 bytes RAM buffer sensor packets before transmission, and the 25 MHz throughput ensures responsive data acquisition at sub-millisecond intervals. The watchdog timer and brown-out reset improve field reliability for unattended sensor installations. Industrial temperature grade and 5 V operation suit process-control analog front ends.
Recomendado
Embedded Control and Educational Platforms
The PIC17C43T-25I/PQ remains useful for educational and legacy embedded designs because of its simple 58-instruction set, RISC architecture, and rich peripheral documentation. With 33 I/O, an 8-bit ADC, USART, and SSP, students can learn timers, interrupts, PWM, and serial protocols on a single chip. The 8 KB OTP holds moderately-sized C or assembly projects, and the 44-MQFP package exposes all pins on standard breakout boards. Recommended PIC18F migration target: PIC18F4220 for new curricula.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC17C43T-25I/PQ — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC17C43T-25/PQ | PIC17C43-16I/PQ | PIC17C42A-25/PT | PIC17CR43T-25I/PQ |
|---|---|---|---|---|---|
| Package | 44-MQFP (10x10 mm) | 44-MQFP (10x10 mm) - same | 44-MQFP (10x10 mm) - same | 44-TQFP | 44-MQFP (10x10 mm) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Maximum Clock Frequency | 25 MHz | 25 MHz | 16 MHz (-36%) | 25 MHz | 25 MHz |
| Program Memory | 8 KB OTP EPROM | 8 KB OTP EPROM | 8 KB OTP EPROM | 4 KB OTP EPROM (-50%) | 4K words Mask ROM |
| Temperature Grade | Industrial -40 to +85 C | Commercial 0 to +70 C | Industrial -40 to +85 C | Commercial 0 to +70 C | Industrial -40 to +85 C |
| I/O Pins | 33 | 33 | 33 | 33 | 33 |
| Program Memory Type | OTP EPROM | OTP EPROM | OTP EPROM | OTP EPROM | Mask ROM (factory programmed) |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Principais diferenciais
- Higher clock speed at same package (vs PIC17C43-16I/PQ)
- Industrial temperature vs commercial (vs PIC17C43T-25/PQ)
- Reprogrammable upgrade path (vs PIC17CR43T-25I/PQ)
Notas de projeto
Estimated: the PIC17C43T-25I/PQ draws up to ~50 mA active at 25 MHz from a 5 V rail, plus I/O sink currents. Place a 100 nF ceramic decoupling capacitor close to each Vdd pin (pins 11 and 32 in the 44-MQFP) and a bulk 10 uF tantalum or aluminum capacitor at the regulator output. Ground returns must use a low-impedance pour connecting both Vss pins (12 and 31). Inductive loads on outputs require flyback diodes and, for relays, separate Vdd rails to prevent MCU reset from supply transients.
Place the 25 MHz crystal or resonator within 5 mm of OSC1 (pin 13) and OSC2 (pin 14) with short, equal-length traces and a ground guard ring to minimize EMI coupling. Keep high-speed digital traces away from the analog ADC inputs (PORTA/PORTE) and add a 100 nF cap on AVdd if the ADC is used. The 44-MQFP package benefits from thermal vias under the die-attach pad area to spread heat during sustained I/O switching at 25 MHz.
The PIC17C43T-25I/PQ uses OTP EPROM: code cannot be erased or rewritten in-circuit. Validate firmware on a JW-windowed CERDIP variant (PIC17C43T-25/JW) or use MPLAB simulator before committing to OTP programming. Brown-out detection and watchdog timer must be enabled in configuration bits to recover from power transients. MCLR (pin 1) requires a 10 kohm pull-up to Vdd; floating MCLR can cause spurious resets. Exceeding 6 V on Vdd permanently damages the device.
Informações de conformidade
RoHS, REACH, lead-free, and halogen-free status not stated in the Verified Web Data for PIC17C43T-25I/PQ; marked 'unknown' until confirmed via manufacturer documentation. Part is not AEC-Q100 qualified - automotive designs should validate or migrate to PIC18F-based parts.
