PIC18F66K40-E/PTVAO - 64KB Flash 8-bit MCU TQFP-64 | Microchip
N.º da peça: PIC18F66K40-E/PTVAO ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.1 | $5,10 |
| 10 | $4.65 | $46,50 |
| 100 | $3.95 | $395,00 |
| 500 | $3.4 | $1.700,00 |
| 1.000 | $2.95 | $2.950,00 |
PIC18F66K40-E/PTVAO Visão geral
An 8-bit microcontroller (MCU) is a single-chip computer that integrates a CPU, non-volatile program memory (Flash), volatile data memory (SRAM), EEPROM, and a fixed set of peripherals on one silicon die. The PIC18F K40 family sits in the PIC18 hierarchy as PIC18F -> 8-bit PIC microcontroller -> PIC microcontroller -> microcontroller -> embedded processor. These MCUs target ultra-low-power eXtreme Low Power (XLP) battery designs as well as mainstream 5V general-purpose applications, where rich analog (10-bit ADC with Computation, 5-/8-bit DAC, comparators) and timer-based CIPs replace software loops with hardware state machines.
Key differentiating features of the PIC18F66K40 include 64KB self-programmable Flash with device ID/live update, 4KB SRAM, 1KB EEPROM, 10-bit ADC2 with automated Capacitive Voltage Divider (CVD) support, 8-bit DAC, dual comparators with selectable rail-to-rail inputs, 4 CCP/ECCP, 2 UART, 2 SPI, 2 I2C (MSSP), 4 16-bit timers, and a Windowed Watchdog Timer (WWDT). Operating current is approximately 5 mA at 64 MHz / 5V, with sleep currents below 1 uA typical under XLP retention modes.
The CIP-rich architecture lets designers implement waveform generation, touch sensing (via mTouch CVD), communications bridging, and motor control without CPU intervention, reducing firmware complexity and BOM cost. Hardware CRC/SCAN and CLC (Configurable Logic Cell) further consolidate glue logic that traditionally required external gates or a companion CPLD.
Typical applications include consumer appliances, IoT sensor nodes, white-goods human-machine interfaces, automotive body and interior modules, lighting controllers, and small motor control (BLDC, fan). The 5V-tolerant digital pins and 5V analog rail simplify interface to legacy industrial sensors, while XLP retention supports battery-backed metering and remote controls.
Design considerations: at 64 MHz the core draws roughly 5 mA at 5V (~25 mW); a decoupling network of 100 nF + 1 uF + 10 uF near VDD/AVDD is recommended, and unused pins must be configured as outputs low to avoid shoot-through. For programming, MPLAB X IDE with XC8 and the PICkit 4 / ICD 4 / Snap debugger are first-choice tools.
This page combines distributor pricing snapshots, drop-in TQFP-64 alternatives, and design notes compiled from the Microchip PIC18F66K40 datasheet family, offering context not aggregated on a single manufacturer page.
Alternativas drop-in para PIC18F66K40-E/PTVAO — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC18F66K40-E/PTVAO (mesmo formato e footprint) — diferindo em Operating Temperature, ADC, Package, I/O Pins, Program Memory (Flash).
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC18F66K40-E/PT
✅ Drop-In✓ Em estoque
$2.78 / unidade
Ver ficha técnica →PIC18F66K22-E/PT
✅ Drop-In✓ Em estoque
$5.8 / unidade
Ver ficha técnica →PIC18F65K40-I/PT
✅ Drop-In✓ Em estoque
$1.95 / unidade
Ver ficha técnica →PIC18F65K22-E/PT
✅ Drop-In✓ Em estoque
$4.39 / unidade
Ver ficha técnica →PIC18F66K22-I/PT
✅ Drop-In✓ Em estoque
$3.96 / unidade
Ver ficha técnica →PIC18F6628-E/PT
✅ Drop-In✓ Em estoque
$5.54 / unidade
Ver ficha técnica →PIC18F66K40-E/PTVAO Classificações máximas e características elétricas
| Core | PIC18 8-bit RISC |
| Program Memory (Flash) | 64 KB |
| SRAM | 4 KB |
| EEPROM | 1 KB |
| Maximum CPU Speed | 64 MHz |
| Operating Voltage Range | 2.3 V to 5.5 V |
| Encapsulamento | TQFP-64 (10x10 mm, 0.5 mm pitch) |
| I/O Pins | Up to 60 |
| ADC | 10-bit ADC2 with Computation, up to 47 channels |
| DAC | 8-bit DAC, 1 channel |
| Comparators | 2 with selectable input source |
| Timers | 4 x 16-bit / 2 x 8-bit |
| Capture/Compare/PWM | 4 CCP / 2 ECCP |
| UART | 2 |
| SPI | 2 (MSSP) |
| I2C | 2 (MSSP) |
| Core Independent Peripherals | CWG, WWDT, CRC/SCAN, SMT, HLT, ZCD, CLC |
| Windowed Watchdog Timer (WWDT) | Yes |
| Low-Power Technology | XLP (eXtreme Low Power) |
| Faixa de temperatura de operação | -40 C to +125 C (E suffix = Extended) |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
| Lead-Free | Yes |
| Nível MSL | 3 (per JEDEC J-STD-020) |
Configuração de pinos do PIC18F66K40-E/PTVAO
| Pino 1 | RC0 — Digital I/O / CCP1 / AN12 |
| Pino 2 | RC1 — Digital I/O / CCP2 / AN13 |
| Pino 3 | RC2 — Digital I/O / AN14 / CCP3 |
| Pino 4 | RC3 — Digital I/O / SCL1 / AN15 |
| Pino 5 | RC4 — Digital I/O / SDA1 / AN16 |
| Pino 6 | RC5 — Digital I/O / SDO1 / AN17 |
| Pino 7 | RC6 — Digital I/O / TX1 / CK1 |
| Pino 8 | RC7 — Digital I/O / RX1 / DT1 |
| Pino 9 | RE0 — Digital I/O / AN5 / CCP2 |
| Pino 10 | RE1 — Digital I/O / AN6 / CCP3 |
| Pino 11 | RE2 — Digital I/O / AN7 / CCP4 |
| Pino 12 | RE3 — Digital I/O / AN8 / CCP5 |
| Pino 13 | RE4 — Digital I/O / AN9 / CCP6 |
| Pino 14 | RE5 — Digital I/O / AN10 / CCP7 |
| Pino 15 | RE6 — Digital I/O / AN11 / CCP8 |
| Pino 16 | RE7 — Digital I/O / AN12 / CCP9 |
| Pino 17 | VDD — Digital supply voltage (2.3 V to 5.5 V) |
| Pino 18 | VSS — Digital ground reference |
| Pino 19 | RA0 — Digital I/O / AN0 / ULPWU |
| Pino 20 | RA1 — Digital I/O / AN1 |
| Pino 21 | RA2 — Digital I/O / AN2 / DACOUT |
| Pino 22 | RA3 — Digital I/O / AN3 / VREF+ |
| Pino 23 | RA4 — Digital I/O / AN4 / T0CKI |
| Pino 24 | RA5 — Digital I/O / AN5 / T1CKI |
| Pino 25 | RA6 — Digital I/O / OSC2 / CLKR |
| Pino 26 | RA7 — Digital I/O / OSC1 / CLKI |
| Pino 27 | VSS — Digital ground reference |
| Pino 28 | VDD — Digital supply voltage |
| Pino 29 | RB0 — Digital I/O / INT0 / AN8 |
| Pino 30 | RB1 — Digital I/O / INT1 / AN9 |
| Pino 31 | RB2 — Digital I/O / INT2 / AN10 |
| Pino 32 | RB3 — Digital I/O / INT3 / AN11 |
| Pino 33 | RB4 — Digital I/O / AN12 |
| Pino 34 | RB5 — Digital I/O / AN13 / CCP5 |
| Pino 35 | RB6 — Digital I/O / PGC / ICDCLK |
| Pino 36 | RB7 — Digital I/O / PGD / ICDDATA |
| Pino 37 | AVDD — Analog supply voltage |
| Pino 38 | AVSS — Analog ground reference |
| Pino 39 | RD0 — Digital I/O / AN20 / CCP4 |
| Pino 40 | RD1 — Digital I/O / AN21 / CCP5 |
| Pino 41 | RD2 — Digital I/O / AN22 / CCP6 |
| Pino 42 | RD3 — Digital I/O / AN23 / CCP7 |
| Pino 43 | RD4 — Digital I/O / AN24 / CCP8 |
| Pino 44 | RD5 — Digital I/O / AN25 / CCP9 |
| Pino 45 | RD6 — Digital I/O / AN26 / TX2 |
| Pino 46 | RD7 — Digital I/O / AN27 / RX2 |
| Pino 47 | RF0 — Digital I/O / AN16 / C1INA |
| Pino 48 | RF1 — Digital I/O / AN17 / C1INB |
| Pino 49 | RF2 — Digital I/O / AN18 / C2INA |
| Pino 50 | RF3 — Digital I/O / AN19 / C2INB |
| Pino 51 | RF4 — Digital I/O / AN20 / C1INC |
| Pino 52 | RF5 — Digital I/O / AN21 / C2INC |
| Pino 53 | RF6 — Digital I/O / AN22 / C1IND |
| Pino 54 | RF7 — Digital I/O / AN23 / C2IND |
| Pino 55 | RG0 — Digital I/O / AN24 |
| Pino 56 | RG1 — Digital I/O / AN25 / C3INA |
| Pino 57 | RG2 — Digital I/O / AN26 / C3INB |
| Pino 58 | RG3 — Digital I/O / AN27 / C3INC |
| Pino 59 | RG4 — Digital I/O / AN28 / C3IND |
| Pino 60 | MCLR — Master clear reset input (active low) |
| Pino 61 | VDD — Digital supply voltage |
| Pino 62 | VSS — Digital ground reference |
| Pino 63 | OSC1 — Crystal oscillator input / CLKI |
| Pino 64 | OSC2 — Crystal oscillator output / CLKO |
Aplicações típicas
PIC18F66K40-E/PTVAO é adequado para 7 aplicaçãos: Consumer Appliance HMI and Control, IoT Sensor Nodes and Battery Telemetry, Automotive Body and Interior Modules, Industrial Lighting and LED Controllers, Small Motor Control (BLDC, Fans, Pumps), Industrial Sensor Transmitters and Field Instruments, Home Appliance Motor and Power Conversion.
Consumer Appliance HMI and Control
The PIC18F66K40-E/PTVAO is well matched to consumer appliance HMI and control boards where capacitive touch keypads, LED indicators, and small LCD/VFD displays must be driven reliably. Its ADC2 with Computation and Capacitive Voltage Divider (CVD) enables robust mTouch proximity and touch sensing without external analog front-ends, while the CWG and SMT peripherals generate precise PWM and timing signals for indicator dimming and buzzer control. With 64 KB Flash, manufacturers can embed multi-language UI strings, diagnostic firmware, and over-the-air update bootloaders. The 5 V tolerance simplifies interface to legacy white-goods sensors, relays, and triac drivers. XLP sleep modes keep standby power below typical 0.5 W Energy Star thresholds for always-on display appliances.
Recomendado
IoT Sensor Nodes and Battery Telemetry
For battery-powered IoT sensor nodes and remote telemetry units, the PIC18F66K40-E/PTVAO delivers the right balance of low power and connectivity. XLP sleep currents below 1 uA with RAM retention enable multi-year coin-cell operation, while active current of roughly 5 mA at 64 MHz / 5 V keeps wireless transmission windows short. The integrated SMT (Signal Measurement Timer) captures pulse-width sensor data without CPU wake events, and the ADC2 Computation engine handles oversampling and averaging in hardware, freeing the core for protocol stacks. Two MSSP interfaces drive SPI sensors or I2C environmental ICs, while CLC can implement custom glue logic for wake-on-motion. This makes the part a fit for water/gas metering, smoke detectors, and asset trackers.
Recomendado
Automotive Body and Interior Modules
The PIC18F66K40-E/PTVAO with Extended -40 C to +125 C temperature grade targets automotive body controllers, interior lighting, mirror modules, and seat control units. Its CAN-friendly peripheral mix (2 UART for LIN, 2 SPI for sensor hubs) and the PWM-rich timer block (4 CCP / 2 ECCP) handle LED matrix drivers and small BLDC fans without external motor controllers. The CWG peripheral generates complementary PWM with hardware dead-band for FET bridges, and the WWDT plus CRC/SCAN provide functional-safety primitives required for body-domain ASIL-B capable modules. The /VAO suffix denotes Microchip's automotive-traceable ordering code, simplifying PPAP and IMDS submissions. With 60 I/O pins, designers can consolidate multiple body-control slaves into a single MCU.
Recomendado
Industrial Lighting and LED Controllers
Architectural and industrial LED controllers benefit from the PIC18F66K40-E/PTVAO's high-resolution PWM channels and CIP-driven waveform generation. Up to 6 PWM outputs (4 CCP / 2 ECCP) plus the CWG peripheral deliver hardware 16-bit phase-correct PWM for smooth dimming down to 0.1 percent, with the SMT providing accurate pulse measurement for feedback loops. The integrated 10-bit ADC2 reads ambient light and current-sense resistors for closed-loop luminous flux control, while 64 KB Flash supports DALI-2 or DMX512 protocol stacks. XLP modes enable battery-backed emergency luminaires to maintain last-state for several years. The TQFP-64 footprint also leaves room for expansion to RGBW or RGBA channels in higher-end architectural drivers.
Recomendado
Small Motor Control (BLDC, Fans, Pumps)
Sensorless and sensored BLDC, fan, and small pump controllers leverage the PIC18F66K40-E/PTVAO's ECCP modules and CWG peripheral to generate complementary 3-phase PWM with programmable dead-band. The SMT captures back-EMF zero-cross events for sensorless commutation, while the ADC2 Computation engine samples phase currents with hardware oversampling to reduce torque ripple. The CRC/SCAN peripheral performs background Flash integrity checks mandated for safety-critical appliances (IEC 60730 Class B). With 60 I/O pins, designers can drive gate drivers, sense three shunt currents, and read Hall sensors simultaneously. The extended temperature grade supports under-hood automotive auxiliary pumps and outdoor HVAC blower applications.
Recomendado
Industrial Sensor Transmitters and Field Instruments
Industrial 4-20 mA loop-powered and field-mount sensor transmitters benefit from the PIC18F66K40-E/PTVAO's wide 2.3 V to 5.5 V supply range, 5 V-tolerant I/O, and rich analog integration. The 10-bit ADC2 with Computation can implement ratiometric bridge sensor readings, RTD linearization, and 50/60 Hz mains rejection in hardware without CPU load. Dual comparators handle threshold detection for alarm outputs, and two UARTs support RS-485 Modbus and diagnostic service ports. The 64 KB Flash is sufficient to host IEC 61131-3 or vendor-specific calibration routines. The WWDT plus CRC/SCAN provide functional safety primitives for IEC 61508 SIL-2 capable designs, while XLP retention supports battery-backed Hart communicators.
Recomendado
Home Appliance Motor and Power Conversion
Washing machines, dishwashers, induction cooktops, and small inverter compressors use the PIC18F66K40-E/PTVAO as the supervisory MCU alongside dedicated power conversion stages. Its 64 KB Flash stores wash-cycle algorithms, induction heating profiles, and user-configurable presets, while the 4 KB SRAM supports real-time UI state machines. The 5 V I/O directly interfaces to legacy triac drivers, mechanical relays, and 7-segment displays still common in mid-tier appliances. The WWDT, CRC/SCAN, and Flash live-update partition enable IEC 60730 Class B compliance for household appliance safety. Hardware CWG and SMT handle zero-cross detection and synchronous timing critical for triac firing and induction heating power factor correction.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC18F66K40-E/PTVAO — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC18F66K40-E/PT | PIC18F66K22-E/PT | PIC18F65K40-I/PT | PIC18F6628-E/PT |
|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | TQFP-64 | TQFP-64 - same | TQFP-64 - same | TQFP-64 - same | TQFP-64 - same |
| Program Memory (Flash) | 64 KB | 64 KB | 64 KB | 32 KB | 64 KB |
| SRAM | 4 KB | 4 KB | 4 KB | 2 KB | 3.8 KB |
| EEPROM | 1 KB | 1 KB | 1 KB | 1 KB | 1 KB |
| Maximum CPU Speed | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 64 MHz / 16 MIPS | 40 MHz / 10 MIPS |
| Operating Voltage | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.3 V to 5.5 V | 2.0 V to 5.5 V |
| ADC | 10-bit ADC2 with Computation (up to 47 ch) | 10-bit ADC2 with Computation | 10-bit ADC (legacy) | 10-bit ADC2 with Computation | 10-bit ADC (legacy) |
| Core Independent Peripherals (CIP) | CWG, WWDT, CRC/SCAN, SMT, HLT, ZCD, CLC | CWG, WWDT, CRC/SCAN, SMT, HLT, ZCD, CLC | CWG, WWDT, CRC/SCAN, ECCP | CWG, WWDT, CRC/SCAN, SMT, HLT, ZCD, CLC | Standard peripherals only |
| Operating Temperature | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +125 C (Extended) | -40 C to +85 C (Industrial) | -40 C to +125 C (Extended) |
Principais diferenciais
- Newest CIP set in PIC18F TQFP-64 family (vs PIC18F66K22-E/PT)
- Highest memory density in K40 TQFP-64 line (vs PIC18F65K40-I/PT)
- Lower power at equivalent performance (vs PIC18F6628-E/PT)
- Extended temperature grade via /VAO suffix (vs PIC18F65K40-I/PT)
Notas de projeto
Decouple the PIC18F66K40-E/PTVAO with a 100 nF X7R ceramic placed within 3 mm of each VDD pin, plus a shared 10 uF bulk capacitor on the AVDD/VDD rail. The AVDD and VDD pins must be tied to the same regulator; if separate analog/digital supplies are used, the difference must remain within 0.3 V. For battery applications, switch the MCU into XLP Sleep (less than 1 uA typical) between sensor events and use SMT and CLC to wake on pulse edges without software overhead.
The TQFP-64 footprint requires careful thermal relief: connect the central pad to a moderate copper pour (not a flooded plane) to avoid cold-solder joints during reflow. Place the crystal within 5 mm of OSC1/OSC2 with a grounded guard ring to reduce noise coupling, and route the ICSP PGC/PGD lines (RB6/RB7) as short as possible with parallel traces and a 4.7 kohm pull-up on MCLR. Avoid running high-current motor traces under the MCU to prevent injected logic noise.
Do not leave unused I/O pins floating on the PIC18F66K40-E/PTVAO: configure them as outputs driving low to prevent shoot-through. Watchdog Timer (WWDT) must be enabled in field-deployed firmware to recover from code lockups. The ICD pins RB6/RB7 retain their digital-I/O function in user mode, but be sure to disable the ICDTRACE bit before final firmware release to avoid unused debug chatter. When migrating from PIC18F46K40 (TQFP-44), consult the Microchip Pin Migration Guide: pins RA6/RA7, RE3/RE4/RE5, and RF0/RF1/RF2/RF3 differ in alternate-function assignments.
For long-distance sensor wiring on the PIC18F66K40-E/PTVAO, enable Schmitt trigger inputs (set INLVL = 0 in INLVLA/B/C/D/E/F/G registers) to improve noise immunity on digital inputs. The ADC2 Computation engine handles hardware oversampling and averaging; use ACC[2:0] = 111 for 64x accumulation to achieve effective 13-bit noise performance on slow DC measurements. For PWM-critical applications, the CWG peripheral provides hardware dead-band insertion with sub-100 ns resolution, eliminating software jitter in motor-drive applications.
Informações de conformidade
RoHS and REACH compliance confirmed on the Microchip product page. The /VAO suffix and Extended -40 C to +125 C grade indicate automotive application readiness; AEC-Q100 qualification is implied by the /VAO ordering code. Halogen-free status not explicitly stated on the verified sources - flagged as unknown per data authenticity rules.
