PIC24FJ64GB004-I/PT - 64KB Flash 16-bit MCU with USB OTG | Microchip
N.º da peça: PIC24FJ64GB004-I/PT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.62 | $5,62 |
| 10 | $5.1 | $51,00 |
| 100 | $4.32 | $432,00 |
| 500 | $3.79 | $1.895,00 |
| 1.000 | $3.3 | $3.300,00 |
PIC24FJ64GB004-I/PT Visão geral
A 16-bit microcontroller (MCU) is a programmable processor that uses a 16-bit data path and instructions, sitting in the embedded hierarchy between 8-bit MCUs (PIC16, AVR, STM8) and 32-bit Cortex-M parts. The PIC24FJ family targets low-power and USB-connected embedded designs that benefit from higher code density and richer peripherals than 8-bit devices, but where a Cortex-M0+/M4 is over-budget on cost or power.
Key features include an on-chip USB 2.0 full-speed OTG transceiver with internal pull-up/pull-down resistors, a 10-bit A/D converter with 13 input channels, four UART, two SPI, two I2C peripherals, five 16-bit timers, and a real-time clock calendar with RTCC alarm. The XLP technology delivers deep sleep currents in the sub-microamp range with multiple power-managed operating modes, making it suited for battery or USB-powered applications.
Architecturally, the PIC24FJ64GB004-I/PT uses a modified Harvard 16-bit core with hardware multiply/divide in a single cycle, a 22K x 24-bit Flash word organization, and a Peripheral Pin Select engine that allows most digital peripherals to be remapped onto alternate pins - a key advantage for board layout versus fixed-pin MCUs. The integrated USB OTG transceiver removes the need for an external TUSB121x PHY, saving 2 to 4 components and avoiding 90-ohm differential trace impedance challenges on dense boards.
Typical applications include USB HID peripherals such as keyboards and custom input devices, USB-to-UART bridge dongles, low-power sensor data loggers with USB charging, medical point-of-care instruments, and consumer accessories requiring USB OTG host or device roles. Its small 44-TQFP footprint and on-chip USB simplify designs that need firmware-updatable USB functionality without an external PHY.
When designing with this part, prioritize the PPS assignment early in the schematic to avoid later re-spins, place a 12 MHz external crystal within 5 mm of OSC1/OSC2 with proper ground guard traces, and follow Microchip's USB hardware design guidelines for the 90-ohm differential D+/D- pair. For lowest sleep current, configure unused peripherals to OFF in firmware and use the deep sleep rather than idle mode.
Alternativas drop-in para PIC24FJ64GB004-I/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC24FJ64GB004-I/PT (mesmo formato e footprint) — diferindo em Package, Program Memory (Flash), Core Architecture, Timers, ADC.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC24FJ32GB004-I/PT
✅ Drop-In✓ Em estoque
$3.72 / unidade
Ver ficha técnica →PIC24FJ64GB002-I/SP
✅ Drop-In✓ Em estoque
$3.05 / unidade
Ver ficha técnica →PIC24FJ128GB004-I/PT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC24FJ64GB004T-I/PT
✅ Drop-In✓ Em estoque
$1.95 / unidade
Ver ficha técnica →PIC24FJ64GB004-I/PTVAO
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ64GB004-I/PT Classificações máximas e características elétricas
| Series | PIC24F XLP |
| Core | PIC24 16-bit |
| Program Memory (Flash) | 64 KB (22K x 24-bit words) |
| RAM | 8 KB |
| Maximum CPU Speed | 32 MHz (8 MIPS) |
| Tensão de alimentação | 3.0 V to 3.6 V |
| Temperatura de operação | -40 C to +85 C (Industrial) |
| Encapsulamento | 44-pin TQFP (PT), 10x10 mm |
| Digital I/O Pins | 33 |
| USB Interface | USB 2.0 Full-Speed OTG, on-chip transceiver |
| ADC | 10-bit, 13 channels |
| UART | 4 |
| SPI | 2 |
| I2C | 2 |
| Timers | 5 x 16-bit |
| Peripheral Pin Select (PPS) | Yes |
| Low-Power Technology | nanoWatt XLP |
| RTCC | Yes |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
Configuração de pinos do PIC24FJ64GB004-I/PT
| Pino 1 | RB0/AN0/CN2/PGED3 — GPIO/ADC/ICSP data |
| Pino 2 | RB1/AN1/CN3/PGEC3 — GPIO/ADC/ICSP clock |
| Pino 3 | RB2/AN2/CN4 — GPIO/ADC |
| Pino 4 | RB3/AN3/CN5 — GPIO/ADC |
| Pino 5 | RA0/AN17 — GPIO/ADC |
| Pino 6 | RA1/AN18 — GPIO/ADC |
| Pino 7 | RA2/AN19 — GPIO/ADC |
| Pino 8 | RA3/AN20 — GPIO/ADC |
| Pino 9 | RA4/AN21 — GPIO/ADC |
| Pino 10 | VSS — Ground |
| Pino 11 | VDD — Supply 3.0-3.6 V |
| Pino 12 | RA5/AN22 — GPIO/ADC |
| Pino 13 | RA6/AN23 — GPIO/ADC/OSC2 |
| Pino 14 | RA7/OSC1 — GPIO/crystal oscillator input |
| Pino 15 | RC0 — GPIO/PPS |
| Pino 16 | RC1 — GPIO/PPS |
| Pino 17 | RC2 — GPIO/PPS |
| Pino 18 | RC3 — GPIO/PPS |
| Pino 19 | RC4 — GPIO/PPS |
| Pino 20 | RC5 — GPIO/PPS |
| Pino 21 | RC6 — GPIO/PPS |
| Pino 22 | RC7 — GPIO/PPS |
| Pino 23 | RC8 — GPIO/PPS |
| Pino 24 | D- — USB data minus |
| Pino 25 | D+ — USB data plus |
| Pino 26 | VBUS — USB VBUS detect |
| Pino 27 | VSS — Ground |
| Pino 28 | VDD — Supply 3.0-3.6 V |
| Pino 29 | RD0 — GPIO/PPS |
| Pino 30 | RD1 — GPIO/PPS |
| Pino 31 | RD2 — GPIO/PPS |
| Pino 32 | RD3 — GPIO/PPS |
| Pino 33 | RD4 — GPIO/PPS |
| Pino 34 | RD5 — GPIO/PPS |
| Pino 35 | RD6 — GPIO/PPS |
| Pino 36 | RD7 — GPIO/PPS |
| Pino 37 | RB4/AN4 — GPIO/ADC |
| Pino 38 | RB5/AN5 — GPIO/ADC |
| Pino 39 | RB6/AN6/PGEC2 — GPIO/ADC/ICSP |
| Pino 40 | RB7/AN7/PGED2 — GPIO/ADC/ICSP |
| Pino 41 | RB8/AN8 — GPIO/ADC |
| Pino 42 | RB9/AN9 — GPIO/ADC |
| Pino 43 | RB10/AN10 — GPIO/ADC |
| Pino 44 | RB11/AN11 — GPIO/ADC |
Aplicações típicas
PIC24FJ64GB004-I/PT é adequado para 6 aplicaçãos: USB HID Peripheral (Keyboard / Mouse / Custom Input), USB-to-UART Bridge Dongle, Low-Power Sensor Data Logger with USB Charging, Medical Point-of-Care Instrument, USB OTG Consumer Accessory, Industrial USB Sensor Module.
USB HID Peripheral (Keyboard / Mouse / Custom Input)
The PIC24FJ64GB004-I/PT is ideally matched to USB HID peripheral designs: its integrated USB 2.0 full-speed transceiver removes an external PHY, 4 UARTs and 2 SPIs drive matrix scanning, 5 x 16-bit timers handle debounce, and nanoWatt XLP supports long battery life. Placed as the only MCU on a small PCB with a 12 MHz crystal and USB-C connector; the on-chip PHY and 8 KB RAM let the firmware run a full HID stack plus macro keycode buffers without external memory.
Recomendado
USB-to-UART Bridge Dongle
For USB-to-UART bridge dongles the PIC24FJ64GB004-I/PT provides a single-chip solution: USB device on one side, 4 hardware UARTs on the other, plus 64 KB Flash for protocol conversion code. Using the on-chip USB transceiver eliminates an external FTDI-style bridge IC, dropping BOM cost and PCB area; PPS lets the UART pins be remapped to match the connector pinout without re-spinning the board.
Recomendado
Low-Power Sensor Data Logger with USB Charging
The PIC24FJ64GB004-I/PT is well suited to battery-powered data loggers that need periodic USB connectivity for charging and data offload. The 10-bit / 13-channel ADC reads analog sensors, 8 KB RAM stores logged samples, the USB OTG port handles both charging and data transfer, and nanoWatt XLP deep-sleep modes keep quiescent current in the sub-microamp range between samples - extending coin-cell runtime dramatically.
Recomendado
Medical Point-of-Care Instrument
For handheld medical instruments such as glucose meters or pulse oximeters, the PIC24FJ64GB004-I/PT delivers a 16-bit instruction set for precise ADC averaging, USB for clinic PC connectivity, and 64 KB Flash to host a graphical UI plus measurement firmware. The 10-bit ADC with 13 channels reads multiple sensor types in parallel, and the -40 C to +85 C industrial temperature range supports refrigerated reagent storage.
Recomendado
USB OTG Consumer Accessory
For tablets and phones that need OTG accessory roles such as game controllers or HID remotes, the PIC24FJ64GB004-I/PT supports USB host, device, and OTG modes from the same MCU. The on-chip transceiver simplifies the BOM; 33 digital I/O with PPS handle buttons, LEDs, and force-feedback H-bridge control signals; and 32 MHz / 8 MIPS performance is sufficient for HID, mass-storage, or vendor-class firmware stacks.
Recomendado
Industrial USB Sensor Module
The PIC24FJ64GB004-I/PT fits industrial 24 V-to-USB sensor bridge modules where 3.3 V regulated rail and USB connectivity coexist. Its -40 C to +85 C industrial grade tolerates factory-floor temperature swings, the 13-channel ADC reads 4 to 20 mA loops via sense resistors, and the integrated USB OTG transceiver eliminates external PHY ICs that struggle at industrial temperatures. PPS remapping keeps the PCB layout clean.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC24FJ64GB004-I/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC24FJ32GB004-I/PT | PIC24FJ64GB002-I/SP | PIC24FJ128GB004-I/PT | PIC24FJ64GB004T-I/PT |
|---|---|---|---|---|---|
| Package | 44-pin TQFP (PT) | 44-pin TQFP (PT) - same | 28-pin SPDIP (SP) | 44-pin TQFP (PT) - same | 44-pin TQFP (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 32 KB | 64 KB | 128 KB | 64 KB |
| RAM | 8 KB | 4 KB | 8 KB | 8 KB | 8 KB |
| USB OTG Transceiver | Yes (on-chip) | Yes (on-chip) | Yes (on-chip) | Yes (on-chip) | Yes (on-chip) |
| CPU Speed | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS | 32 MHz / 8 MIPS |
| Operating Voltage | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V | 3.0 V to 3.6 V |
| Industrial Temp Grade | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C | -40 C to +85 C |
Principais diferenciais
- Integrated USB 2.0 full-speed OTG transceiver (vs PIC24FJ64GA004-I/PT)
- 2x Flash memory of PIC24FJ32GB004-I/PT in same footprint (vs PIC24FJ32GB004-I/PT)
- nanoWatt XLP deep-sleep for battery applications (vs Generic PIC24F non-XLP MCU)
Notas de projeto
Estimated: route the USB D+ / D- differential pair with 90-ohm controlled impedance, length-matched within 150 mil, and isolated from switching signals by a ground guard trace. Place the VBUS detect pin voltage divider within 5 mm of pin 26 and add 4.7 uF bulk capacitance on VDD pins 11 and 28. Per Microchip USB hardware design guide, USB traces should not cross power or clock edges to maintain USB compliance.
Do not leave DISVREG floating when not using the internal 2.5 V regulator - tie it to VSS for normal 3.3 V operation. All VSS pins (10 and 27) must be connected even if the device appears to function with one floating; incomplete VSS bonding can cause programming failures and erratic ADC readings at low temperatures.
Place the 12 MHz crystal or resonator within 5 mm of OSC1 (pin 14) and OSC2 (pin 13), with short symmetric traces and a ground guard ring. Add 22 pF load capacitors tied to VSS. The ICSP programming pins (PGED3/PGEC3 on RB0/RB1 and PGED2/PGEC2 on RB7/RB6) should be brought to a 0.1 inch header to support in-circuit programming without disturbing the PCB layout.
Informações de conformidade
RoHS and REACH compliant per Microchip product page. Standard PIC24FJ64GB004-I/PT is not AEC-Q100; use PIC24FJ64GB004-I/PTVAO ordering code for automotive/medical grade variants.