PIC24FJ64GB106-I/PT - 16-Bit 64KB Flash USB OTG MCU | Microchip
N.º da peça: PIC24FJ64GB106-I/PT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $5.3 | $5,30 |
| 10 | $4.77 | $47,70 |
| 100 | $4.24 | $424,00 |
| 500 | $3.71 | $1.855,00 |
| 1.000 | $3.18 | $3.180,00 |
PIC24FJ64GB106-I/PT Visão geral
Background: A microcontroller (MCU) is a single-chip computer that integrates a CPU core, non-volatile program memory (Flash), volatile data memory (RAM), and programmable I/O peripherals. The PIC24F family uses a 16-bit modified Harvard RISC architecture with instruction pipelining, sitting in the hierarchy of "microcontroller -> embedded processor -> semiconductor IC". The PIC24FJ64GB106 adds native USB 2.0 On-The-Go (OTG) hardware, eliminating the need for an external USB transceiver or PHY.
Key features include 64KB Flash program memory (22K x 24 words), 16KB SRAM, 64KB device ROM-less operation, up to 32 MHz operation (16 MIPS at 3.3V), and a rich peripheral mix: 3x I2C, 3x SPI, 4x UART, 23 independent timers, a 10-bit ADC with 500 ksps, and USB OTG with dedicated DMA. The "-I" suffix indicates the industrial temperature grade (-40C to +85C), and "/PT" indicates the 64-pin TQFP package. eXtreme Low Power (XLP) technology delivers standby currents below 100 nA, enabling battery-friendly designs.
Technical depth: The PIC24FJ64GB106 implements a hardware USB OTG controller with internal transceiver, charge pump, and voltage regulator, supporting both device and host roles. The 16-bit CPU features a 16x16 hardware multiplier and a 32x16 hardware divider in one instruction cycle. Multiple power management modes (Run, Doze, Sleep, Deep Sleep) and on-chip LDO simplify battery-powered designs. JTAG/ICSP boundary scan is included for test and programming.
Typical applications: USB peripherals (HID, CDC, mass storage, audio class), low-power sensor hubs with USB logging, embedded web servers with TCP/IP stacks, capacitive touch keypads, and industrial control nodes. The integrated USB and large RAM make it suitable for USB device classes that require buffer memory (16KB) for protocol handling.
Design consideration: The 64-pin TQFP package requires 1.0 mm PCB land pattern and provides generous I/O for parallel buses and multiple serial interfaces. Place the 22 nF Vcap decoupling capacitor as close as possible to the dedicated Vcap pin (pin 56 in this package), since the internal core regulator requires this external capacitor for stability.
This page synthesizes distributor pricing, same-brand and cross-brand drop-in alternatives in the same 64-TQFP footprint, and practical design notes not found in the manufacturer datasheet alone.
Alternativas drop-in para PIC24FJ64GB106-I/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC24FJ64GB106-I/PT (mesmo formato e footprint) — diferindo em Package, ADC, Timers, Program Memory (Flash), Core Architecture.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC24FJ128GB106-I/PT
✅ Drop-In✓ Em estoque
$4.54 / unidade
Ver ficha técnica →PIC24FJ256GB106-I/PT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ64GB004-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.3 / unidade
Ver ficha técnica →PIC24FJ64GB110-I/PT
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
PIC24FJ128GB110-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.78 / unidade
Ver ficha técnica →PIC24FJ256GB110-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$5.62 / unidade
Ver ficha técnica →PIC24FJ64GB106-I/PT Classificações máximas e características elétricas
| Core | PIC24F (16-bit RISC) |
| Program Memory (Flash) | 64 KB (22K x 24 words) |
| RAM | 16 KB |
| CPU Speed | Up to 32 MHz (16 MIPS at 3.3V) |
| Operating Voltage | 2.0 V to 3.6 V |
| USB | USB 2.0 OTG (Host/Device/OTG) with internal transceiver |
| I2C | 3 |
| SPI | 3 |
| UART | 4 |
| Timers (16-bit) | 5 + 2x 32-bit |
| Total Timers (independent) | 23 |
| ADC | 10-bit, 500 ksps, up to 16 channels |
| GPIOs | 52 |
| Temperatura de operação | -40C to +85C (Industrial) |
| Encapsulamento | 64-pin TQFP (PT) 10x10 mm |
| Tipo de montagem | Surface Mount |
| Nível MSL | 3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
| Lead-Free | Yes |
Configuração de pinos do PIC24FJ64GB106-I/PT
| Pino 1 | RP0/CN0/RB0 — Remappable peripheral pin / interrupt-on-change / GPIO RB0 |
| Pino 2 | RP1/CN1/RB1 — Remappable peripheral pin / interrupt-on-change / GPIO RB1 |
| Pino 3 | RP2/CN2/RB2 — Remappable peripheral pin / interrupt-on-change / GPIO RB2 |
| Pino 4 | RP3/CN3/RB3 — Remappable peripheral pin / interrupt-on-change / GPIO RB3 |
| Pino 5 | RP4/CN4/RB4 — Remappable peripheral pin / interrupt-on-change / GPIO RB4 |
| Pino 6 | RP5/CN5/RB5 — Remappable peripheral pin / interrupt-on-change / GPIO RB5 |
| Pino 7 | RP6/CN6/RB6 — Remappable peripheral pin / interrupt-on-change / GPIO RB6 |
| Pino 8 | RP7/CN7/RB7 — Remappable peripheral pin / interrupt-on-change / GPIO RB7 |
| Pino 9 | RP8/CN8/RB8 — Remappable peripheral pin / interrupt-on-change / GPIO RB8 |
| Pino 10 | RP9/CN9/RB9 — Remappable peripheral pin / interrupt-on-change / GPIO RB9 |
| Pino 11 | VSS — Ground reference |
| Pino 12 | VDD — Positive supply voltage (2.0V to 3.6V) |
| Pino 13 | RP10/CN10/RB10 — Remappable peripheral pin / interrupt-on-change / GPIO RB10 |
| Pino 14 | RP11/CN11/RB11 — Remappable peripheral pin / interrupt-on-change / GPIO RB11 |
| Pino 15 | RP12/CN12/RB12 — Remappable peripheral pin / interrupt-on-change / GPIO RB12 |
| Pino 16 | RP13/CN13/RB13 — Remappable peripheral pin / interrupt-on-change / GPIO RB13 |
| Pino 17 | RP14/CN14/RB14 — Remappable peripheral pin / interrupt-on-change / GPIO RB14 |
| Pino 18 | RP15/CN15/RB15 — Remappable peripheral pin / interrupt-on-change / GPIO RB15 |
| Pino 19 | VSS — Ground reference |
| Pino 20 | VDD — Positive supply voltage (2.0V to 3.6V) |
| Pino 21 | RA0/AN0 — GPIO RA0 / analog input AN0 |
| Pino 22 | RA1/AN1 — GPIO RA1 / analog input AN1 |
| Pino 23 | RA2/AN2 — GPIO RA2 / analog input AN2 |
| Pino 24 | RA3/AN3 — GPIO RA3 / analog input AN3 |
| Pino 25 | RA4/AN4 — GPIO RA4 / analog input AN4 |
| Pino 26 | RA5/AN5 — GPIO RA5 / analog input AN5 |
| Pino 27 | RA6/AN6 — GPIO RA6 / analog input AN6 |
| Pino 28 | RA7/AN7 — GPIO RA7 / analog input AN7 |
| Pino 29 | RC1 — GPIO RC1 |
| Pino 30 | RC2 — GPIO RC2 |
| Pino 31 | RC3 — GPIO RC3 |
| Pino 32 | RC4 — GPIO RC4 |
| Pino 33 | RD0 — GPIO RD0 |
| Pino 34 | RD1 — GPIO RD1 |
| Pino 35 | RD2 — GPIO RD2 |
| Pino 36 | RD3 — GPIO RD3 |
| Pino 37 | RD4 — GPIO RD4 |
| Pino 38 | RD5 — GPIO RD5 |
| Pino 39 | RD6 — GPIO RD6 |
| Pino 40 | RD7 — GPIO RD7 |
| Pino 41 | RD8 — GPIO RD8 |
| Pino 42 | RD9 — GPIO RD9 |
| Pino 43 | RD10 — GPIO RD10 |
| Pino 44 | RD11 — GPIO RD11 |
| Pino 45 | RD12 — GPIO RD12 |
| Pino 46 | RD13 — GPIO RD13 |
| Pino 47 | RD14 — GPIO RD14 |
| Pino 48 | RD15 — GPIO RD15 |
| Pino 49 | RC12 — GPIO RC12 |
| Pino 50 | RC13 — GPIO RC13 |
| Pino 51 | RC14 — GPIO RC14 |
| Pino 52 | RC15 — GPIO RC15 |
| Pino 53 | VSS — Ground reference |
| Pino 54 | VDD — Positive supply voltage (2.0V to 3.6V) |
| Pino 55 | ENVREG — Enable for internal USB voltage regulator (tie to VDD or float per config) |
| Pino 56 | VCAP — Internal 1.8V core LDO output - connect 22 nF low-ESR ceramic to ground |
| Pino 57 | D+ — USB D+ differential data line |
| Pino 58 | D- — USB D- differential data line |
| Pino 59 | VBUS — USB VBUS sensing input (5V tolerant) |
| Pino 60 | VUSB3V3 — USB 3.3V internal regulator output |
| Pino 61 | OSC1/CLKI — Crystal oscillator input or external clock input |
| Pino 62 | OSC2/CLKO — Crystal oscillator output or clock output |
| Pino 63 | MCLR — Master clear (reset) input, active low |
| Pino 64 | RA15 — GPIO RA15 |
Aplicações típicas
PIC24FJ64GB106-I/PT é adequado para 6 aplicaçãos: USB HID Peripheral (Keyboard / Mouse / Custom HID), USB Mass Storage Data Logger, Industrial Sensor Hub with USB Diagnostics Port, Capacitive Touch Keypad with USB Output, Embedded Web Server with TCP/IP over USB RNDIS, Battery-Powered Portable USB Device.
USB HID Peripheral (Keyboard / Mouse / Custom HID)
The PIC24FJ64GB106-I/PT is a natural fit for USB HID devices because its integrated USB 2.0 OTG controller eliminates the external PHY and provides hardware DMA channels that offload packet handling from the CPU. The 16KB on-chip RAM comfortably buffers HID report queues and class-specific descriptors without external memory, and the 32 MHz core runs HID stacks with low latency. The Microchip MLA / MCHPFSUSB stack ships ready-to-use HID, CDC, MSD, and audio class examples. Power consumption is dominated by the USB bus (VBUS detection), allowing bus-powered HID designs without local regulation. The 64-pin TQFP gives 52 GPIOs for matrix-scanned keypads, indicator LEDs, and rotary encoders.
Recomendado
USB Mass Storage Data Logger
For USB mass storage class (MSC) loggers that write sensor data to a USB flash drive, the PIC24FJ64GB106-I/PT offers 16KB RAM to buffer writes and 64KB Flash for the file system and application code. The integrated OTG host capability allows the MCU to act as a USB host and mount FAT-formatted flash drives without an external PHY. eXtreme Low Power (XLP) technology with sub-100 nA standby current lets the logger sleep between sensor acquisitions, extending battery life in remote deployments. The 10-bit 500 ksps ADC supports up to 16 analog channels for environmental or industrial telemetry. The 64-pin TQFP provides ample I/O for SD card fall-back, user buttons, and status LEDs.
Recomendado
Industrial Sensor Hub with USB Diagnostics Port
The PIC24FJ64GB106-I/PT suits industrial sensor hubs that expose USB diagnostics (CDC class) to host PCs while running sensor acquisition on local GPIOs and SPI/I2C buses. The MCU provides 3x SPI and 3x I2C for connecting sensors and 4x UARTs for legacy industrial protocols (RS-232/RS-485). Industrial -40C to +85C temperature rating covers factory-floor deployment. The 23 timers (5x 16-bit + 2x 32-bit + RTCC) handle precise sampling intervals and pulse counting for flow meters or encoders. The integrated 10-bit ADC at 500 ksps handles analog sensor reads. A USB diagnostic port enables field firmware upgrades and real-time data visualization without a separate programmer.
Recomendado
Capacitive Touch Keypad with USB Output
The PIC24FJ64GB106-I/PT integrates capacitive touch sensing hardware (mTouch / CTMU) and USB output in a single chip, eliminating the need for a separate touch controller and USB bridge. Per Microchip documentation, the Charge Time Measurement Unit (CTMU) converts capacitance to digital counts, and mTouch libraries run on the 32 MHz MIPS core. The 64-pin TQFP gives enough GPIOs for 12-16 touch electrodes plus indicator LEDs. The Microchip MLA USB stack ships a HID-class touch demo. Low-power sleep with CTMU wake-on-touch extends battery life in remote or portable keypads, while USB bus power eliminates local batteries entirely.
Recomendado
Embedded Web Server with TCP/IP over USB RNDIS
For low-cost embedded web servers, the PIC24FJ64GB106-I/PT can present itself as a USB RNDIS Ethernet device to a host PC, allowing browser-based configuration of headless equipment. The 16KB RAM accommodates a lightweight TCP/IP stack (Microchip MLA TCP/IP) and HTTP response buffers, while 64KB Flash holds HTML pages and CGI scripts. The 32 MHz MIPS core services HTTP requests with low latency. Per Microchip documentation, MLA includes RNDIS and CDC-ECM examples that compile for this part. Industrial -40C to +85C operation enables building automation and HVAC equipment with web management interfaces.
Recomendado
Battery-Powered Portable USB Device
The PIC24FJ64GB106-I/PT fits portable USB devices that draw from a Li-ion or Li-poly cell thanks to eXtreme Low Power (XLP) technology and on-chip LDO. The device operates down to 2.0V, enabling full battery utilization before low-battery cutoff. Sub-100 nA Deep Sleep current extends shelf life and idle time. The integrated USB OTG controller with internal charge pump supports USB device operation directly from VBUS or battery via a boost converter. The 64-pin TQFP gives 52 GPIOs for displays, sensors, and user inputs. The 10-bit ADC at 500 ksps monitors battery voltage and current for accurate fuel gauging.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC24FJ64GB106-I/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC24FJ128GB106-I/PT | PIC24FJ256GB106-I/PT | PIC24FJ64GB004-I/PT | PIC24FJ64GB110-I/PT | PIC24FJ128GB110-I/PT |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 64-pin TQFP (PT) 10x10 mm | 64-pin TQFP (PT) 10x10 mm - same | 64-pin TQFP (PT) 10x10 mm - same | 64-pin TQFP (PT) 10x10 mm - same | 64-pin TQFP (PT) 10x10 mm - same | 64-pin TQFP (PT) 10x10 mm - same |
| Flash | 64 KB | 128 KB (+100%) | 256 KB (+300%) | 64 KB (same) | 64 KB (same) | 128 KB (+100%) |
| RAM | 16 KB | 16 KB (same) | 16 KB (same) | 16 KB (same) | 16 KB (same) | 16 KB (same) |
| USB | USB 2.0 OTG (Host/Device) | USB 2.0 OTG (same) | USB 2.0 OTG (same) | USB 2.0 OTG (same) | USB 2.0 OTG (same) | USB 2.0 OTG (same) |
| CPU Speed | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS (same) | 32 MHz / 16 MIPS (same) | 32 MHz / 16 MIPS (same) | 32 MHz / 16 MIPS (same) | 32 MHz / 16 MIPS (same) |
| Operating Voltage | 2.0V to 3.6V | 2.0V to 3.6V (same) | 2.0V to 3.6V (same) | 2.0V to 3.6V (same) | 2.0V to 3.6V (same) | 2.0V to 3.6V (same) |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) | -40C to +85C (same) |
| UART | 4 | 4 (same) | 4 (same) | 4 (same) | 4 (same) | 4 (same) |
Principais diferenciais
- Higher Flash density with identical 64-TQFP pinout (vs PIC24FJ128GB106-I/PT)
- Largest Flash option in same 64-TQFP package (vs PIC24FJ256GB106-I/PT)
- eXtreme Low Power with sub-100 nA standby (vs PIC24FJ64GA106-I/PT (non-USB variant))
Notas de projeto
The PIC24FJ64GB106-I/PT requires a 22 nF low-ESR ceramic capacitor on the Vcap pin (pin 56) to stabilize the internal 1.8V core LDO. Place the capacitor as close as physically possible to the pin, with short traces and a direct ground return. Use X7R dielectric rated for at least 6.3V (X5R is acceptable). Do not substitute with values below 10 nF or above 33 nF - LDO stability is not guaranteed outside this range. For battery-powered designs, the ENVREG pin must be tied per datasheet recommendations to enable internal USB voltage regulation from VBUS.
USB D+ and D- traces must be routed as a 90-ohm differential pair with matched length (delta under 2 mm). Place the series termination resistor (typically 27-33 ohm on each line, near the MCU side) close to the MCU pins. Keep USB traces away from noisy switching rails and clock traces; if crossing is unavoidable, cross at 90 degrees. The VBUS pin requires a 1uF decoupling cap to ground. Maintain a continuous ground reference beneath the USB pair, ideally as an unbroken polygon on layer 2, to control impedance and provide a return path for common-mode currents.
Common pitfalls with the PIC24FJ64GB106-I/PT include: (1) Forgetting the Vcap capacitor, which prevents the core from running at all; (2) Sharing the USB bus with high-current loads without proper VBUS sensing; (3) Using XT with HFINTOSC settings inconsistently - the USB module requires the primary oscillator (XT or HS) to be active during USB transactions per the datasheet; (4) Exceeding 25 mA per GPIO source/sink without considering the package's total sink budget (200 mA for the device); (5) Programming the device without configuring the JTAG/ICSP pins as analog inputs when JTAG is disabled - this prevents boundary-scan from interfering with the application.
The PIC24FJ64GB106-I/PT draws approximately 25 mA at full CPU speed with USB active, dissipating well under 100 mW even at 3.6V - thermal management is not a concern for this part under normal conditions. However, in enclosed industrial enclosures where ambient approaches +85C, verify that GPIO sink current per pin (25 mA) and total package dissipation limits are not violated. The 64-pin TQFP package is rated for -40C to +85C operation and provides adequate thermal mass for typical embedded applications.
Informações de conformidade
RoHS compliant and lead-free per Microchip product page. Not AEC-Q100 qualified - choose -E/PT grade for automotive applications requiring -40C to +125C. MSL 3 moisture sensitivity per JEDEC J-STD-020. REACH declaration available through Microchip product compliance portal.
