PIC24FJ64GB108T-I/PT - 64KB Flash USB MCU 80-TQFP | Microchip
N.º da peça: PIC24FJ64GB108T-I/PT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $7.82 | $7,82 |
| 10 | $7.1 | $71,00 |
| 100 | $6.32 | $632,00 |
| 500 | $5.55 | $2.775,00 |
| 1.000 | $4.92 | $4.920,00 |
PIC24FJ64GB108T-I/PT Visão geral
What is a microcontroller? A microcontroller (MCU) is a single-chip computer that integrates a CPU core, program memory (typically Flash), data memory (RAM), and a rich set of peripherals such as timers, communication interfaces, ADC/DAC modules, and I/O. The PIC24F sits in Microchip's 16-bit MCU hierarchy: PIC24F (low-power, Flash) -> PIC24 (16-bit) -> MCU -> microcontroller -> embedded system-on-chip. This hierarchy places the device firmly in the industrial and consumer embedded space, where deterministic real-time response and rich connectivity are required.
Key features of the PIC24FJ64GB108T-I/PT include its USB 2.0 full-speed On-The-Go (OTG) transceiver, three I2C peripherals, three SPI peripherals, four UART modules, and 23 independent timers. The 17-bit by 16-bit hardware multiplier and 16-bit hardware divider accelerate DSP-class math without software overhead, and the C-compiler-optimized architecture (MPLAB XC16) ensures code density. Standby current under 100 nA makes it well-suited for battery-powered designs, while the broad peripheral set reduces bill-of-materials cost.
Typical applications span USB peripherals (HID, CDC, MSD, audio class), low-power wireless sensor nodes, industrial data loggers, and human-interface panels. The combination of USB-OTG, ample RAM (16KB) for buffering, and low standby current also suits portable medical instruments and USB charging/host controllers.
When designing with this part, engineers should leverage MPLAB X IDE and the MPLAB Snap or PICkit 4 for programming/debugging via the 6-pin ICSP interface, and consult the device datasheet for USB bus-powering topologies (self-powered vs bus-powered). The 80-pin TQFP provides ample I/O but requires careful PCB escape routing; a 4-layer board is recommended for USB signal integrity.
Alternativas drop-in para PIC24FJ64GB108T-I/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC24FJ64GB108T-I/PT (mesmo formato e footprint) — diferindo em Package, MSL Level, Timers, I/O Pins, Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC24FJ64GB108-I/PT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ128GB108-I/PT
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ128GB110-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.78 / unidade
Ver ficha técnica →PIC24FJ256GB108-I/PT
✅ Drop-In✓ Em estoque
$5.42 / unidade
Ver ficha técnica →PIC24FJ64GA108T-I/PT
✅ Drop-In✓ Em estoque
$3.99 / unidade
Ver ficha técnica →PIC24FJ64GB106T-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.86 / unidade
Ver ficha técnica →PIC24FJ64GB108T-I/PT Classificações máximas e características elétricas
| Architecture | PIC24F (16-bit modified Harvard) |
| Core Size | 16-bit |
| Program Memory (Flash) | 64 KB (22K x 24) |
| RAM | 16 KB |
| Maximum CPU Speed | 32 MHz (16 MIPS) |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Temperatura de operação | -40 C to +85 C (Industrial) |
| Encapsulamento | 80-pin TQFP (PT), 12x12 mm |
| Tipo de montagem | Surface Mount |
| I/O Pins | 65 |
| USB Interface | USB 2.0 Full-Speed with On-The-Go (OTG) |
| I2C Peripherals | 3 |
| SPI Peripherals | 3 |
| UART Modules | 4 |
| Timers | 23 (16-bit and 32-bit) |
| Hardware Multiplier | 17-bit x 16-bit (single cycle) |
| Hardware Divider | 16-bit / 16-bit |
| Internal Oscillator | 8 MHz with 4x PLL and multiple divide options |
| Standby Current | <100 nA (typical, per datasheet) |
| Nível MSL | 3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
| Programming/Debug | ICSP via MPLAB Snap / PICkit 4 |
| Compiler Support | MPLAB XC16 (C), MPASM (assembly) |
Configuração de pinos do PIC24FJ64GB108T-I/PT
| Pino 1 | RP15/C1IN-/AN15/PMD15/CN15/RB15 — Remappable peripheral / analog input / PMP data |
| Pino 2 | RP14/C1IN+/AN14/PMD14/CN14/RB14 — Remappable peripheral / analog input / PMP data |
| Pino 3 | RP13/AN13/PMD13/CN13/RB13 — Remappable peripheral / analog input |
| Pino 4 | RP12/AN12/PMD12/CN12/RB12 — Remappable peripheral / analog input |
| Pino 5 | RP11/AN11/PMD11/CN11/RB11 — Remappable peripheral / analog input |
| Pino 6 | RP10/AN10/PMD10/CN10/RB10 — Remappable peripheral / analog input |
| Pino 7 | RP9/AN9/PMD9/CN9/RB9 — Remappable peripheral / analog input |
| Pino 8 | RP8/AN8/PMD8/CN8/RB8 — Remappable peripheral / analog input |
| Pino 9 | RP7/AN7/PMD7/CN7/RB7 — Remappable peripheral / analog input |
| Pino 10 | RP6/AN6/PMD6/CN6/RB6 — Remappable peripheral / analog input |
| Pino 11 | RP5/AN5/PMD5/CN5/RB5 — Remappable peripheral / analog input |
| Pino 12 | RP4/AN4/PMD4/CN4/RB4 — Remappable peripheral / analog input |
| Pino 13 | RP3/AN3/PMD3/CN3/RB3 — Remappable peripheral / analog input |
| Pino 14 | RP2/AN2/PMD2/CN2/RB2 — Remappable peripheral / analog input |
| Pino 15 | RP1/AN1/PMD1/CN1/RB1 — Remappable peripheral / analog input |
| Pino 16 | RP0/AN0/PMD0/CN0/RB0 — Remappable peripheral / analog input |
| Pino 17 | VDD — Positive supply voltage (2.0 V to 3.6 V) |
| Pino 18 | VCAP — External filter capacitor for internal core voltage regulator |
| Pino 19 | VSS — Ground reference |
| Pino 20 | OSC1/RA0 — Oscillator crystal input / general I/O |
| Pino 21 | OSC2/RA1 — Oscillator crystal output / general I/O |
| Pino 22 | SOSCO/RPC0/RA2 — Secondary oscillator output / general I/O |
| Pino 23 | SOSCI/RPC1/RA3 — Secondary oscillator input / general I/O |
| Pino 24 | D- — USB D- data line (full-speed) |
| Pino 25 | D+ — USB D+ data line (full-speed) |
| Pino 26 | VBUS — USB VBUS detect input |
| Pino 27 | VUSB3V3 — USB internal 3.3 V regulator output (decoupling) |
| Pino 28 | RA4 — General I/O |
| Pino 29 | RA5 — General I/O |
| Pino 30 | RA6 — General I/O |
| Pino 31 | RA7 — General I/O |
| Pino 32 | RC2 — General I/O |
| Pino 33 | RC3 — General I/O |
| Pino 34 | RC4 — General I/O |
| Pino 35 | RC5 — General I/O |
| Pino 36 | RD0 — General I/O |
| Pino 37 | RD1 — General I/O |
| Pino 38 | RD2 — General I/O |
| Pino 39 | RD3 — General I/O |
| Pino 40 | RD4 — General I/O |
| Pino 41 | RD5 — General I/O |
| Pino 42 | RD6 — General I/O |
| Pino 43 | RD7 — General I/O |
| Pino 44 | RF0 — General I/O |
| Pino 45 | RF1 — General I/O |
| Pino 46 | RF2 — General I/O |
| Pino 47 | RF3 — General I/O |
| Pino 48 | RF4 — General I/O |
| Pino 49 | RF5 — General I/O |
| Pino 50 | RF6 — General I/O |
| Pino 51 | RF7 — General I/O |
| Pino 52 | RG0 — General I/O |
| Pino 53 | RG1 — General I/O |
| Pino 54 | RG2 — General I/O |
| Pino 55 | RG3 — General I/O |
| Pino 56 | RG6 — General I/O |
| Pino 57 | RG7 — General I/O |
| Pino 58 | RG8 — General I/O |
| Pino 59 | RG9 — General I/O |
| Pino 60 | RG12 — General I/O |
| Pino 61 | RG13 — General I/O |
| Pino 62 | RG14 — General I/O |
| Pino 63 | RG15 — General I/O |
| Pino 64 | RE0 — General I/O |
| Pino 65 | RE1 — General I/O |
| Pino 66 | RE2 — General I/O |
| Pino 67 | RE3 — General I/O |
| Pino 68 | RE4 — General I/O |
| Pino 69 | RE5 — General I/O |
| Pino 70 | RE6 — General I/O |
| Pino 71 | RE7 — General I/O |
| Pino 72 | MCLR — Master clear (reset) input, active low |
| Pino 73 | PGEC1/RA8 — ICSP programming clock / general I/O |
| Pino 74 | PGED1/RA9 — ICSP programming data / general I/O |
| Pino 75 | PGEC2/RA10 — ICSP alternate clock / general I/O |
| Pino 76 | PGED2/RA11 — ICSP alternate data / general I/O |
| Pino 77 | RA12 — General I/O |
| Pino 78 | RA13 — General I/O |
| Pino 79 | RA14 — General I/O |
| Pino 80 | RA15 — General I/O |
Aplicações típicas
PIC24FJ64GB108T-I/PT é adequado para 7 aplicaçãos: USB HID Peripherals, USB CDC Serial Bridges, Battery-Powered Data Loggers, Industrial Control Panels, Portable Medical Devices, USB Audio Class Devices, IoT Sensor Edge Nodes.
USB HID Peripherals
The PIC24FJ64GB108T-I/PT is an ideal host MCU for USB Human Interface Device (HID) peripherals such as keyboards, mice, game controllers, and custom HID-class input devices. Its integrated USB 2.0 full-speed OTG transceiver eliminates the need for an external PHY, reducing BOM cost and PCB area. With 16 KB of RAM and 64 KB Flash, the device can implement full HID report descriptors, consumer-control pages, and composite device stacks without external memory. Engineers can leverage Microchip's MLA USB stack and the MPLAB Code Configurator to generate HID class drivers quickly. The 32 MHz / 16 MIPS core provides sufficient throughput for USB polling at 1 kHz with margin for button debouncing and LED driving.
Recomendado
USB CDC Serial Bridges
For USB-to-UART bridge applications, the PIC24FJ64GB108T-I/PT integrates USB device, UART, and a fast 16-bit core that supports up to 921.6 kbps serial data rates alongside USB full-speed enumeration. The four UART modules enable multi-port USB-to-serial adapters or industrial gateway designs where multiple RS-232/RS-485 channels must be exposed to a host PC. With 65 GPIO available and industrial temperature rating (-40 C to +85 C), the part fits in factory-floor equipment and outdoor installations. Microchip's CDC class driver provides plug-and-play behavior on Windows, macOS, and Linux without additional driver installation.
Recomendado
Battery-Powered Data Loggers
The PIC24FJ64GB108T-I/PT excels in battery-powered data logging applications where its sub-100 nA standby current enables multi-year battery life when duty-cycled. The 16 KB RAM provides substantial buffer space for sensor samples before batch upload via USB, and the 23 timers support precise wake/sleep scheduling without external RTC chips. Engineers can use the on-chip 10-bit ADC with multiple channels to sample temperature, humidity, pressure, or analog sensor signals at intervals of seconds to hours. The 3.3 V VDD range is compatible with lithium coin-cell and primary battery chemistries when used with a boost regulator.
Recomendado
Industrial Control Panels
The PIC24FJ64GB108T-I/PT drives industrial control panels that combine USB configuration ports, multiple serial fieldbuses (RS-232, RS-485), and segmented LCD or LED indicators. Its 4x UART modules can simultaneously handle Modbus RTU on RS-485, a debug UART, and two inter-MCU communication channels. The 65 GPIO support keypad scanning, LCD data bus, status LEDs, and isolated digital I/O via opto-couplers. The -40 C to +85 C industrial temperature range and Microchip's long-term product longevity program make this MCU a fit for factory automation where 10-15 year product lifecycles are required.
Recomendado
Portable Medical Devices
For portable medical devices such as pulse oximeters, glucose meters, and handheld ultrasound probes, the PIC24FJ64GB108T-I/PT offers a compact 80-pin TQFP solution with USB device or USB-OTG connectivity for charging and data transfer to a host PC or tablet. The low standby current extends battery life between charges, while the 16 MIPS performance supports real-time DSP filtering of bio-sensor signals. The 16 KB RAM enables substantial sample buffering, and the hardware multiplier accelerates FIR/IIR filter calculations. USB-OTG support allows the medical device to act as both a device (charging) and host (reading from a USB accessory).
Recomendado
USB Audio Class Devices
The PIC24FJ64GB108T-I/PT implements USB audio class 1.0 devices such as USB microphones, USB speakers, and USB headsets, leveraging its USB full-speed peripheral and 16 MIPS performance for sample rates up to 48 kHz. The three SPI peripherals can drive external audio DACs and ADCs, while the 16 KB RAM supports audio sample buffering with minimal software overhead. The eXtreme Low Power architecture is advantageous for battery-powered USB headsets where the MCU can sleep during silence and wake on USB SOF tokens. Microchip's USB audio class stack provides a drop-in firmware framework for quick product development.
Recomendado
IoT Sensor Edge Nodes
The PIC24FJ64GB108T-I/PT serves as an edge MCU in IoT sensor nodes that communicate with a host gateway over USB or via local UART/SPI peripherals to a wireless module. With 64 KB Flash and 16 KB RAM, the device can host application logic, a small TCP/IP stack over USB-ECM (Ethernet Control Model), and sensor fusion algorithms. The 4x UART modules enable simultaneous connection to a Wi-Fi or LoRa module, a debug console, and two wired sensor buses. The industrial temperature rating supports outdoor and industrial IoT deployments.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC24FJ64GB108T-I/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC24FJ64GB108-I/PT | PIC24FJ128GB108-I/PT | PIC24FJ256GB108-I/PT | PIC24FJ64GA108T-I/PT |
|---|---|---|---|---|---|
| Package | TQFP-80 (PT) | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same | TQFP-80 (PT) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 64 KB | 64 KB | 128 KB (+100%) | 256 KB (+300%) | 64 KB |
| RAM | 16 KB | 16 KB | 16 KB | 16 KB | 16 KB |
| CPU Speed | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS | 32 MHz / 16 MIPS |
| USB Interface | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | None (USB absent) |
| I/O Pins | 65 | 65 | 65 | 65 | 65 |
| Operating Temperature | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) | -40 C to +85 C (Industrial) |
Principais diferenciais
- Integrated USB 2.0 Full-Speed OTG with on-chip transceiver (vs PIC24FJ64GA108T-I/PT)
- Larger RAM for buffering on the same die (vs PIC24FJ64GB106T-I/PT)
- 23 timers including 32-bit options for flexible PWM/capture (vs PIC24FJ64GA010T-I/PT)
Notas de projeto
Estimated: The PIC24FJ64GB108T-I/PT's VDD range of 2.0 V to 3.6 V requires a 3.3 V LDO or buck regulator upstream. For USB bus-powered designs, a 5 V to 3.3 V LDO such as Microchip's MCP1700 or MCP1727 is typical. Place 1uF and 0.1 uF decoupling capacitors as close as possible to each VDD/VSS pair on the TQFP-80, with a bulk 10uF tantalum or ceramic on the main 3.3 V rail. The VUSB3V3 pin (USB transceiver internal regulator output) requires a 0.01uF decoupling cap and should not be used to power external circuits.
USB signal integrity is critical for full-speed (12 Mbps) compliance. Route the D+ and D- traces as a 90-ohm differential pair with matched length (within 150 mil), keep them short, and place a common-mode choke or ferrite bead near the connector. A 4-layer PCB with a dedicated ground plane is strongly recommended; 2-layer boards can pass USB compliance if carefully laid out with ground returns under the D+/D- traces. The VBUS pin requires a 1uF decoupling capacitor and a divider network (or direct connection) to the 5 V USB input for VBUS detection.
Do not omit the VCAP pin decoupling capacitor (typically 10uF ceramic) on pin 18; without it the internal core voltage regulator will not start reliably and the part will appear non-functional. The MCLR pin (pin 72) must be pulled up to VDD via a 10 kohm resistor and have a 100 nF decoupling cap to ground for noise immunity. The ICSP programming pins (PGEC1/PGED1, pins 73/74) are shared with general I/O and should be reserved for programming/debug access in production designs. Forgetting to enable the PLL or wrong oscillator configuration in firmware is a common startup failure mode.
The TQFP-80 (PT) package has a theta_JA of approximately 50 C/W when mounted on a standard 4-layer JEDEC test board. Estimated: at maximum CPU activity (32 MHz, all peripherals active, USB transmitting continuously), the device draws around 30 mA at 3.3 V, dissipating approximately 100 mW. This yields a junction temperature rise of only 5 C above ambient, so no heatsink is required even at industrial 85 C ambient. However, in enclosed industrial enclosures with no airflow, derate the maximum ambient by 10-15 C to maintain margin.
Informações de conformidade
RoHS and REACH compliant per Microchip product page. Industrial temperature grade (-40 C to +85 C). Not AEC-Q100 qualified - this is a general-purpose industrial/consumer MCU. Lead-free and halogen-free per Microchip environmental compliance documentation. MSL Level 3 per JEDEC J-STD-020.