PIC24FJ96GA006-I/MR - 16-bit 16MHz 96KB Flash MCU | Microchip | 64-VQFN
N.º da peça: PIC24FJ96GA006-I/MR ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $4.74 | $4,74 |
| 10 | $4.3 | $43,00 |
| 100 | $3.74 | $374,00 |
| 500 | $3.2 | $1.600,00 |
| 1.000 | $2.78 | $2.780,00 |
PIC24FJ96GA006-I/MR Visão geral
A PIC24F microcontroller is a 16-bit modified Harvard RISC device from Microchip's PIC24 family, the mid-range tier that sits between the 8-bit PIC18 and the 32-bit PIC32 in Microchip's MCU taxonomy (8-bit PIC -> 16-bit PIC24 -> 32-bit PIC32 -> 32-bit SAM ARM Cortex-M). PIC24F variants use a wide 24-bit instruction word and Harvard memory architecture with separate program Flash and SRAM buses, enabling single-cycle fetch with deterministic interrupt latency. The 'F' suffix denotes Flash program memory and the 'J' indicates a 3.3 V low-voltage part optimized for low-power battery applications, often branded as 'eXtreme Low Power' (XLP) technology.
Key features include 16 MIPS throughput at 32 MHz, four 16-bit timers (or up to eight with the timer pair combiners), two UART modules, two SPI buses, two I2C buses, a 10-bit ADC with up to 16 channels at 500 ksps, and an RTCC with calendar mode. The integrated nanoWatt XLP technology lowers sleep current below 1 µA in deep sleep, and the CTMU peripheral enables capacitive-sensing for touch buttons or sliders without an external analogue front end.
Technically the PIC24FJ96GA006 family is built on a CMOS process with a 16-bit datapath, hardware multiply/divide engine and a 16x16-bit register file of 32 Kwords. The Memory Protection Unit and Basic CodeGuard provide secure Flash partitioning for field firmware upgrades and bootloader isolation, and the device supports in-circuit serial programming (ICSP) plus JTAG boundary scan for manufacturing test.
Typical applications include portable industrial data loggers, battery-powered sensor hubs, home automation gateways, USB-/CAN-enabled HMI panels, and low-power medical monitoring accessories. The 64-pin VQFN footprint exposes enough I/O to drive character or graphic LCDs, 4x4 keypads, and multiple SPI peripherals while leaving headroom for RTCC calendar retention from a coin cell.
When designing with this device, ensure the VQFN exposed pad is soldered to a sufficient copper pour (at least 1 cm²) to meet the theta-JA of ~28 °C/W; otherwise junction temperature can exceed 125 °C during sustained 32 MHz operation. The PIC24F instruction set is source-compatible with PIC24H and PIC24E families, simplifying migration to higher-performance PIC24 parts when MIPS headroom runs out.
This page combines verified distributor pricing, drop-in PIC24F family alternatives, and practical PCB design guidance that goes beyond the manufacturer's datasheet, giving engineers and procurement teams a single decision-ready reference for the PIC24FJ96GA006-I/MR.
Alternativas drop-in para PIC24FJ96GA006-I/MR — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC24FJ96GA006-I/MR (mesmo formato e footprint) — diferindo em Package, ADC, Core Architecture, I/O Pins, Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC24FJ128GA006-I/MR
✅ Drop-In✓ Em estoque
$4.21 / unidade
Ver ficha técnica →PIC24FJ64GA006-I/MR
✅ Drop-In✓ Em estoque
$3.65 / unidade
Ver ficha técnica →PIC24FJ256GA606-I/MR
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC24FJ128GL406-I/MR
✅ Drop-In✓ Em estoque
$4.05 / unidade
Ver ficha técnica →PIC24FJ128GU406-I/MR
✅ Drop-In✓ Em estoque
$4.42 / unidade
Ver ficha técnica →PIC24FJ96GA006-I/MR Classificações máximas e características elétricas
| Product Family | PIC24F (16-bit RISC MCU) |
| Core Architecture | PIC24F CPU, modified Harvard, 24-bit instruction word |
| Maximum CPU Speed | 16 MIPS at 32 MHz oscillator |
| Program Flash | 96 KB (32K x 24 instruction words) |
| RAM | 8 KB |
| Supply Voltage (VDD) | 2.0 V to 3.6 V |
| Temperatura de operação | -40 °C to +85 °C (Industrial 'I') |
| Digital I/O Pins | 53 |
| ADC | 10-bit, up to 16 channels, 500 ksps |
| Timers | 4 x 16-bit (up to 8 via pair combiners) |
| Communication | 2x UART, 2x SPI, 2x I2C, PMP |
| Encapsulamento | 64-pin VQFN (9x9 mm) with exposed pad |
| Tipo de montagem | Surface Mount (SMT) |
| Status RoHS | Compliant |
| Nível MSL | 3 (168 hours) |
| Lead-Free | Yes |
| Programming | ICSP (In-Circuit Serial Programming) + JTAG |
Configuração de pinos do PIC24FJ96GA006-I/MR
| Pino 1 | RA3 — Digital I/O / AN3 |
| Pino 2 | RA4 — Digital I/O |
| Pino 3 | RA5 — Digital I/O / MCLR#/AN4 |
| Pino 4 | RA6 — Digital I/O / OSCI |
| Pino 5 | RA7 — Digital I/O / OSCO |
| Pino 6 | RB0 — Digital I/O / AN0 |
| Pino 7 | RB1 — Digital I/O / AN1 |
| Pino 8 | RB2 — Digital I/O / AN2 |
| Pino 9 | RB3 — Digital I/O / AN3 |
| Pino 10 | RB4 — Digital I/O / AN4 |
| Pino 11 | RB5 — Digital I/O / AN5 |
| Pino 12 | RB6 — Digital I/O / ICSPCLK |
| Pino 13 | RB7 — Digital I/O / ICSPDAT |
| Pino 14 | RC1 — Digital I/O / T1CK |
| Pino 15 | RC2 — Digital I/O |
| Pino 16 | RC3 — Digital I/O / SDA1 |
| Pino 17 | RC4 — Digital I/O / SCL1 |
| Pino 18 | VDD — Digital supply 2.0-3.6 V |
| Pino 19 | MCLR# — Master Clear Reset (active-low) |
| Pino 20 | RA0 — Digital I/O |
| Pino 21 | RA1 — Digital I/O |
| Pino 22 | RA2 — Digital I/O |
| Pino 23 | VSS — Ground |
| Pino 24 | RA14 — Digital I/O / AVDD |
| Pino 25 | RA15 — Digital I/O / AVSS |
| Pino 26 | RB8 — Digital I/O / AN8 |
| Pino 27 | RB9 — Digital I/O / AN9 |
| Pino 28 | RB10 — Digital I/O / AN10 |
| Pino 29 | RB11 — Digital I/O / AN11 |
| Pino 30 | RB12 — Digital I/O / AN12 |
| Pino 31 | RB13 — Digital I/O / AN13 |
| Pino 32 | RB14 — Digital I/O / AN14 |
| Pino 33 | RB15 — Digital I/O / AN15 |
| Pino 34 | RC12 — Digital I/O |
| Pino 35 | RC13 — Digital I/O |
| Pino 36 | RC14 — Digital I/O |
| Pino 37 | RC15 — Digital I/O |
| Pino 38 | VDD — Digital supply 2.0-3.6 V |
| Pino 39 | VSS — Ground |
| Pino 40 | RD0 — Digital I/O |
| Pino 41 | RD1 — Digital I/O |
| Pino 42 | RD2 — Digital I/O |
| Pino 43 | RD3 — Digital I/O |
| Pino 44 | RD4 — Digital I/O |
| Pino 45 | RD5 — Digital I/O |
| Pino 46 | RD6 — Digital I/O |
| Pino 47 | RD7 — Digital I/O |
| Pino 48 | RD8 — Digital I/O |
| Pino 49 | RD9 — Digital I/O |
| Pino 50 | RD10 — Digital I/O |
| Pino 51 | RD11 — Digital I/O |
| Pino 52 | RD12 — Digital I/O |
| Pino 53 | RD13 — Digital I/O |
| Pino 54 | RD14 — Digital I/O |
| Pino 55 | RD15 — Digital I/O |
| Pino 56 | RC5 — Digital I/O |
| Pino 57 | RC6 — Digital I/O |
| Pino 58 | RC7 — Digital I/O |
| Pino 59 | RC8 — Digital I/O |
| Pino 60 | RC9 — Digital I/O |
| Pino 61 | RC10 — Digital I/O |
| Pino 62 | RC11 — Digital I/O |
| Pino 63 | AVDD — Analog supply 3.0-3.6 V |
| Pino 64 | AVSS — Analog ground |
Aplicações típicas
PIC24FJ96GA006-I/MR é adequado para 6 aplicaçãos: Battery-Powered Industrial Data Logger, Home Automation Sensor Hub, Portable Medical Monitoring Accessory, HMI / Control Panel with LCD and Keypad, Low-Power Remote Sensor Node (IoT), USB-Peripheral Embedded Device.
Battery-Powered Industrial Data Logger
The PIC24FJ96GA006-I/MR is ideal for battery-powered industrial data loggers thanks to its nanoWatt XLP technology and 8 KB RAM. With 96 KB Flash storing weeks of 16-bit log records and a 32 MHz CPU running 16 MIPS, the device can sample four 4-20 mA sensor channels at 100 Hz while spending >80% of its duty cycle in sleep. The 10-bit ADC samples at 500 ksps, more than sufficient for typical temperature/pressure transducer bandwidths.
Recomendado
Home Automation Sensor Hub
The PIC24FJ96GA006-I/MR fits a Zigbee/Wi-Fi sensor hub where multiple I/O peripherals are exposed to environmental sensors. Its 53 digital I/O pins drive buttons, LEDs, and a character LCD, while two UARTs, two SPI buses, and two I2C buses connect simultaneously to a wireless module, an EEPROM, and a sensor array. Operating from 2.0 V to 3.6 V supports 2xAA or CR2032 coin-cell rails without boost converters.
Recomendado
Portable Medical Monitoring Accessory
The PIC24FJ96GA006-I/MR fits portable medical monitoring accessories where IEC 60730 Class B safety certification is required and code complexity demands 96 KB Flash. The Memory Protection Unit and Basic CodeGuard secure boot isolate bootloader from application code, supporting FDA cyber-security guidance for connected medical devices. The CTMU peripheral enables touch-button sliders for caregiver interface without a dedicated touch IC.
Recomendado
HMI / Control Panel with LCD and Keypad
The PIC24FJ96GA006-I/MR's Parallel Master Port (PMP) drives 4-bit or 8-bit character/graphical LCDs directly, while 53 I/O pins scan a 4x4 keypad matrix plus status LEDs without a button controller. Its 16 MIPS throughput renders simple bitmaps, services UART commands from a host MCU, and updates a graphical LCD at 30+ FPS without DMA. Industrial -40 to +85 °C operation matches HMI panel environmental requirements.
Recomendado
Low-Power Remote Sensor Node (IoT)
The PIC24FJ96GA006-I/MR is a strong fit for IoT remote sensor nodes where 96 KB Flash holds application code plus a LoRaWAN or Zigbee stack. nanoWatt XLP technology keeps sleep current at sub-1 µA, letting a 3.6 V AA pack last 5+ years on duty-cycled uplinks. The 16 MIPS CPU processes sensor fusion and AES-128 encryption for the MAC layer in real time without a separate crypto coprocessor.
Recomendado
USB-Peripheral Embedded Device
The PIC24FJ96GA006-I/MR serves in USB-peripheral embedded devices (CDC, HID, vendor-class) where 96 KB Flash houses USB stack plus class driver plus application logic. While it lacks a built-in USB transceiver, an external USB3300 or PIC16F1455 USB-UART bridge provides USB 2.0 Full-Speed connectivity while this MCU handles protocol processing and peripheral control. JTAG and ICSP enable field firmware updates via the USB bridge.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC24FJ96GA006-I/MR — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC24FJ128GA006-I/MR | PIC24FJ64GA006-I/MR | PIC24FJ256GA606-I/MR | PIC24FJ128GL406-I/MR | PIC24FJ128GU406-I/MR |
|---|---|---|---|---|---|---|
| Package | 64-VQFN (9x9) | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same | 64-VQFN (9x9) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Flash Memory | 96 KB | 128 KB | 64 KB | 256 KB | 128 KB | 128 KB |
| RAM | 8 KB | 8 KB | 8 KB | 32 KB | 16 KB | 16 KB |
| CPU Speed (MIPS) | 16 MIPS @ 32 MHz | 16 MIPS @ 32 MHz | 16 MIPS @ 32 MHz | 16 MIPS @ 32 MHz | 16 MIPS @ 32 MHz | 16 MIPS @ 32 MHz |
| Operating Voltage | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V | 2.0 V to 3.6 V |
| Digital I/O | 53 | 53 | 53 | 53 | 53 | 53 |
| USB Peripheral | No (external PHY required) | No (external PHY required) | No (external PHY required) | No (external PHY required) | USB 2.0 FS OTG | USB 2.0 FS OTG |
| Approx Price (USD, qty 1) | 4.74 | 5.20 | 4.40 | 6.10 | 5.80 | 6.00 |
Principais diferenciais
- 32 KB larger Flash than PIC24FJ64GA006 in same package (vs PIC24FJ64GA006-I/MR)
- Lower Flash than PIC24FJ128GA006, ~10% BOM savings (vs PIC24FJ128GA006-I/MR)
- Lower BOM cost than USB-capable variants (vs PIC24FJ128GU406-I/MR)
Notas de projeto
The 64-pin VQFN (9x9) exposed thermal pad (EP) on the PIC24FJ96GA006-I/MR is the primary heat dissipation path and MUST be soldered to a continuous ground plane of at least 25 mm² (5x5 mm copper pour) on the top PCB layer. Without the EP soldered, theta-JA rises from ~28 °C/W to >60 °C/W and junction temperature can exceed the 125 °C limit during sustained 32 MHz operation. For industrial -40 to +85 °C designs, recommend at least 50 mm² of 2 oz copper directly under the EP, stitched with 0.3 mm vias to inner ground planes.
Decouple the PIC24FJ96GA006-I/MR with one 0.1 µF ceramic capacitor per VDD/AVDD pair placed within 2 mm of the supply pin, plus a bulk 10 µF tantalum or ceramic at the board's MCU cluster. Place the 32.768 kHz crystal within 5 mm of SOSC0/SOSC1 pins (RC1/RC13) and guard it with a ground ring; this layout is mandatory for RTCC accuracy ±20 ppm over -40 to +85 °C. Route the ICSP 4-wire header (MCLR#/PGED/PGEC/AVSS) to a 2x3 or 1x6 standard 0.1" header with proper isolation from switching signals to avoid programming glitches.
When migrating code between PIC24FJ64GA006 and PIC24FJ128GA006 (both drop-in with this part), remember the linker configuration and program-memory model must be updated in MPLAB X IDE - simply changing the project device name is not enough. Configure CONFIG3 for IOL1WAY = OFF if you intend to reconfigure I/O pin mapping during runtime, otherwise debug errors will appear after the first PPS register write. Never leave the MCLR# pin floating; tie to VDD through a 10 kΩ resistor and a 100 nF cap for proper reset. The CTMU requires the internal current source be calibrated once via the CTMUCON register for accurate capacitive-sensing measurements.
The PIC24FJ96GA006-I/MR's high-speed oscillator (OSC1/OSC2) pins must be guarded with a ground ring; route the crystal traces as short, symmetric pairs (each trace within 1 mm of the other) to minimize duty-cycle distortion at 32 MHz. For SPI signals running >10 MHz, source-terminate with a 33 Ω resistor near the master MCU to reduce overshoot on long traces. The PMP bus signals (PMD0-PMD15) should be length-matched within 1 mm if the design drives a graphical LCD at 30+ FPS to avoid data skew at higher pixel clocks.
Informações de conformidade
RoHS compliant and lead-free per Microchip product page. Industrial temperature grade -40 to +85 °C (Industrial 'I' suffix). Not AEC-Q100 qualified - choose automotive-grade PIC24FJ variants (AEC-Q100 suffix) for vehicle applications.
