PIC32MX220F032DT-I/TL - 40MHz 32-bit MCU, 32KB Flash | Microchip
N.º da peça: PIC32MX220F032DT-I/TL ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $3.42 | $3,42 |
| 10 | $3.08 | $30,80 |
| 100 | $2.74 | $274,00 |
| 500 | $2.45 | $1.225,00 |
| 1.000 | $2.18 | $2.180,00 |
PIC32MX220F032DT-I/TL Visão geral
A microcontroller (MCU) is a single-chip processor that integrates a CPU core, memory (Flash for code, SRAM for data), and programmable peripherals. The 32-bit MCU category sits between 8/16-bit microcontrollers (e.g., PIC16, PIC24) and application processors (e.g., Cortex-A). PIC32 devices use the MIPS M4K architecture, which delivers high code density and deterministic interrupt response for embedded control. Within the PIC32 family hierarchy, MX-class devices are general-purpose, MZ-class devices add higher performance and FPU/DSP, and the PIC32MX2xx sub-family targets cost-sensitive USB-enabled designs.
Key features of the PIC32MX220F032DT-I/TL include Peripheral Pin Select (PPS) for flexible pin-function remapping, a 4-channel hardware DMA controller with automatic data-size detection, separate PLLs for the CPU and USB clocks (allowing 48 MHz USB without disturbing system timing), and a Charge Time Measurement Unit (CTMU) for capacitive sensing. Five 16-bit timers/counters and a Real-Time Clock/Calendar (RTCC) module support motor control, periodic sampling, and timekeeping. The device is offered in industrial temperature grade (-40C to +85C) and supports JTAG and 2-wire programming/debug.
Typical applications include low-cost USB peripherals (HID, CDC, custom classes), small graphical user interfaces using PMP-driven LCDs, sensor hubs for IoT protocol end-points, and battery-powered data loggers. The combination of USB, PMP, and CTMU enables designers to add touch input and USB connectivity with a single chip, replacing discrete USB-to-UART bridges and external ADCs in compact products.
When designing with the PIC32MX220F032DT-I/TL, observe the USB electrical requirements (48 MHz clock accuracy, board layout for portable impedance) and provide adequate decoupling on VDD/VUSB. Use MPLAB X IDE with the XC32 compiler; project libraries such as the Microchip USB Framework and Harmony simplify USB stack integration and reduce firmware development time significantly.
Alternativas drop-in para PIC32MX220F032DT-I/TL — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC32MX220F032DT-I/TL (mesmo formato e footprint) — diferindo em Package, Timers, ADC, DMA Channels, I/O Pins.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC32MX220F032D-I/TL
✅ Drop-In✓ Em estoque
$2.54 / unidade
Ver ficha técnica →PIC32MX220F032DT-I/ML
✅ Drop-In✓ Em estoque
$2.03 / unidade
Ver ficha técnica →PIC32MX230F064D-I/TL
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$1.71 / unidade
Ver ficha técnica →PIC32MX270F256D-I/TL
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.5 / unidade
Ver ficha técnica →PIC32MX210F016DT-I/TL
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$2.1 / unidade
Ver ficha técnica →PIC32MX170F256D-I/TL
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.16 / unidade
Ver ficha técnica →PIC32MX220F032DT-I/TL Classificações máximas e características elétricas
| Core Architecture | MIPS32 M4K 32-bit RISC |
| Maximum CPU Clock | 40 MHz |
| Program Memory (Flash) | 32 KB (32K x 8) |
| Data Memory (SRAM) | 8 KB |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| I/O Pins | 34 |
| Encapsulamento | 44-pin VTLA (6x6 mm) with exposed pad |
| Tipo de montagem | Surface Mount |
| Temperatura de operação | -40C to +85C (Industrial) |
| USB Module | USB 2.0 Full-Speed Device/Host/OTG |
| ADC | 10-bit, up to 13 channels |
| Timers | 5 x 16-bit |
| UART Modules | 2 |
| I2C Modules | 2 |
| Parallel Master Port (PMP) | Yes |
| DMA Channels | 4 with auto data-size detection |
| Peripheral Pin Select (PPS) | Yes |
| CTMU (Capacitive Touch) | Yes |
| Status RoHS | Compliant |
Configuração de pinos do PIC32MX220F032DT-I/TL
| Pino 1 | SVDD — Switcher VDD output (internal regulator output) |
| Pino 2 | AN0/CVD7/RPB0/PMD0 — Analog input 0 / CVD cap 7 / GPIO RB0 / PMP data 0 |
| Pino 3 | AN1/CVD8/RPB1/PMD1 — Analog input 1 / CVD cap 8 / GPIO RB1 / PMP data 1 |
| Pino 4 | AN2/CVD9/RPB2/PMD2 — Analog input 2 / CVD cap 9 / GPIO RB2 / PMP data 2 |
| Pino 5 | AN3/RPB3/PMD3 — Analog input 3 / GPIO RB3 / PMP data 3 |
| Pino 6 | AN4/RPB4/PMD4 — Analog input 4 / GPIO RB4 / PMP data 4 |
| Pino 7 | AN5/RPB5/PMD5 — Analog input 5 / GPIO RB5 / PMP data 5 |
| Pino 8 | VSS — Ground reference |
| Pino 9 | OSC1/CLKI/RC13 — Crystal oscillator input / external clock input / GPIO RC13 |
| Pino 10 | OSC2/CLKO/RC14 — Crystal oscillator output / clock output / GPIO RC14 |
| Pino 11 | VDD — Positive supply voltage (2.3-3.6 V) |
| Pino 12 | RA0 — GPIO RA0 |
| Pino 13 | RA1 — GPIO RA1 |
| Pino 14 | RB6/PGEC1 — GPIO RB6 / Programming clock (ICSP) |
| Pino 15 | RB7/PGED1 — GPIO RB7 / Programming data (ICSP) |
| Pino 16 | RA2 — GPIO RA2 |
| Pino 17 | RA3 — GPIO RA3 |
| Pino 18 | RA4 — GPIO RA4 |
| Pino 19 | RA5 — GPIO RA5 |
| Pino 20 | RA6 — GPIO RA6 |
| Pino 21 | RC0 — GPIO RC0 |
| Pino 22 | VUSB — USB 3.3 V supply voltage (powered from internal LDO when USB provided) |
| Pino 23 | D+ — USB D+ data line |
| Pino 24 | D- — USB D- data line |
| Pino 25 | RB8 — GPIO RB8 |
| Pino 26 | RB9 — GPIO RB9 |
| Pino 27 | RB10 — GPIO RB10 |
| Pino 28 | AVDD — Analog supply voltage (must be equal to VDD) |
| Pino 29 | AVSS — Analog ground reference |
| Pino 30 | AN6/RPB11 — Analog input 6 / GPIO RB11 |
| Pino 31 | AN7/RPB12 — Analog input 7 / GPIO RB12 |
| Pino 32 | AN8/RPB13 — Analog input 8 / GPIO RB13 |
| Pino 33 | AN9/RPB14 — Analog input 9 / GPIO RB14 |
| Pino 34 | AN10/RPB15 — Analog input 10 / GPIO RB15 |
| Pino 35 | VSS — Ground reference |
| Pino 36 | RC1 — GPIO RC1 |
| Pino 37 | RC2 — GPIO RC2 |
| Pino 38 | RC3 — GPIO RC3 |
| Pino 39 | RC4 — GPIO RC4 |
| Pino 40 | RC5 — GPIO RC5 |
| Pino 41 | RC6 — GPIO RC6 |
| Pino 42 | RC7 — GPIO RC7 |
| Pino 43 | RC8 — GPIO RC8 |
| Pino 44 | RTCC/RPA7 — RTCC output / GPIO RA7 (also VBAT on some PIC32 variants) |
Aplicações típicas
PIC32MX220F032DT-I/TL é adequado para 7 aplicaçãos: USB HID Peripheral (Keyboard/Mouse/Gamepad), Industrial Sensor Hub with USB Diagnostics, Small Graphical LCD Interface via PMP, USB-to-UART/I2C Bridge, Capacitive Touch User Interface, IoT Edge Node / Sensor Data Logger, Battery-Powered Data Acquisition.
USB HID Peripheral (Keyboard/Mouse/Gamepad)
The PIC32MX220F032DT-I/TL's integrated USB 2.0 Full-Speed device controller and 32 KB Flash make it an ideal core for USB HID peripherals such as keyboards, mice, gamepads, and consumer-control remotes. The 40 MHz MIPS M4K core executes HID class drivers comfortably alongside application logic, while the 8 KB SRAM holds endpoint buffers plus report data structures without external memory. The Peripheral Pin Select (PPS) feature routes USB, UART, and GPIO to any user-defined pin, simplifying PCB layout. Connect the D+/D- lines to pins 23/24 with the recommended 15 K pull-down on D- for full-speed detection. With Microchip's free USB Framework, designers complete HID enumeration in days rather than months. Compared to discrete USB chips with VCOM, the integrated approach reduces BOM cost by 30-50% and frees board area for compact consumer peripherals.
Recomendado
Industrial Sensor Hub with USB Diagnostics
Use the PIC32MX220F032DT-I/TL as a USB-connected sensor hub for industrial monitoring equipment, leveraging its 10-bit ADC up to 13 channels, two UARTs for RS-485/RS-232 sensor chains, and USB device interface for configuration/datalogging on a host PC. The 32 KB Flash accommodates Modbus protocol libraries plus sensor-conditioning code; the 8 KB SRAM is sufficient for 4-channel DMA-driven ADC sampling at 100 Hz while sustaining USB throughput. The 2.3-3.6 V supply range accepts 3.3 V regulated industrial buses and battery-backed configurations. The exposed thermal pad dissipates self-generated heat in sealed IP65 enclosures. Compared to discrete ADC+MCU designs, the integrated approach reduces component count, BOM, and assembly cost while improving long-term availability of the sensing chain.
Recomendado
Small Graphical LCD Interface via PMP
The PIC32MX220F032DT-I/TL's integrated Parallel Master Port (PMP) drives small graphical TFT or OLED LCDs (up to 8-bit parallel bus) without an external display controller, simplifying BOM for compact HMI products. The 40 MHz core comfortably refreshes QVGA (320x240) monochrome panels at 30+ fps while running application logic. The 8 KB SRAM holds display framebuffers for small panels; the 32 KB Flash stores font tables and basic UI code. The CTMU module supports capacitive touch keys on the same PCB, enabling touch+HMI integration with a single MCU. The exposed pad of the 44-VTLA package aids thermal dissipation in fanless sealed HMI units. Compared to SPI-display designs with external controllers, the integrated PMP+CTMU approach reduces both component count and assembly cost.
Recomendado
USB-to-UART/I2C Bridge
The PIC32MX220F032DT-I/TL is an excellent USB-to-UART/I2C bridge, replacing dedicated bridge ICs such as FTDI chips and reducing BOM cost. The integrated USB 2.0 Full-Speed device and two UART modules allow transparent serial port emulation on a host PC (CDC class) while the second UART bridges to a target device. The Peripheral Pin Select feature routes UART/I2C pins flexibly to simplify PCB layout. The 32 KB Flash is more than sufficient for CDC enumeration (CIR) and small protocol stacks. The exposed thermal pad of the 44-VTLA package supports industrial temperature operation. Compared to discrete FTDI-based bridges, the integrated approach costs less and removes the dependency on a specific bridge vendor.
Recomendado
Capacitive Touch User Interface
The PIC32MX220F032DT-I/TL's integrated Charge Time Measurement Unit (CTMU) and Peripheral Pin Select enable cost-effective capacitive touch buttons, sliders, and proximity sensors without dedicated touch ICs. The 32 KB storage holds mTouch firmware and application logic, and the 8 KB SRAM provides ample touch-scan buffer space. Two I2C modules allow the MCU to act as a touch slave to a host processor while USB is reserved for diagnostics/firmware updates. The 2.3-3.6 V supply range supports battery-powered touch interfaces. The 34 I/O pins multiplex across touch channels and other functions via PPS. Compared to dedicated touch ICs, the integrated approach reduces system cost while adding USB and firmware flexibility.
Recomendado
IoT Edge Node / Sensor Data Logger
The PIC32MX220F032DT-I/TL is well suited for IoT edge nodes that aggregate sensor data via I2C/UART and expose it locally via USB or store it in non-volatile memory. The two I2C buses connect multiple sensors concurrently, while two UARTs support RS-485 sensor chains. The 32 KB storage holds simple JSON payloads plus command and protocol stacks. The 8 KB SRAM supports 4-channel DMA-driven I2C/UART reception, offloading buffer memory during burst logging. The exposed-pad the 44-VTLA package supports industrial temperature operation in harsh environments. Compared to discrete MCU+UART designs, the integrated approach reduces component count and improves long-term availability of the sensing chain.
Recomendado
Battery-Powered Data Acquisition
The PIC32MX220F032DT-I/TL's multiple low-power modes (Sleep, Idle, and deep-sleep modes) combined with the 2.3-3.6 V supply range make it suitable for battery-powered data acquisition modules in field deployments. The 10-bit ADC up to 13 channels multiplexes multiple analog sensors, while the four DMA channels minimize CPU wake-time for power efficiency. The 32 KB Flash holds field-calibration tables and compact data loggers. The exposed-pad 44-VTLA package supports industrial temperature operation in harsh environments. Compared to high-performance Cortex-M designs, the integrated approach balances performance, USB, and low-power operation in a single low-cost chip.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC32MX220F032DT-I/TL — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC32MX220F032D-I/TL | PIC32MX220F032DT-I/ML | PIC32MX230F064D-I/TL | PIC32MX270F256D-I/TL | PIC32MX210F016DT-I/TL | PIC32MX170F256D-I/TL |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 44-VTLA (6x6 mm) | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same | 44-VTLA (6x6 mm) - same |
| Core | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Maximum CPU Clock | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz | 40 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 64 KB | 256 KB | 16 KB | 256 KB |
| SRAM | 8 KB | 8 KB | 8 KB | 8 KB | 32 KB | 4 KB | 64 KB |
| USB Controller | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | USB 2.0 FS OTG | No USB |
| Supply Voltage | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V | 2.3 V to 3.6 V |
| Operating Temperature | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
| Approx. Price (qty 1, as of 2026-10-01) | $3.42 | ~$3.30 (tray pack) | ~$3.42 (T&R) | ~$3.85 | ~$5.20 | ~$3.10 | ~$4.90 |
Principais diferenciais
- Lowest-cost USB-capable PIC32 in 44-VTLA footprint (vs PIC32MX170F256D-I/TL)
- 40 MHz core with Peripheral Pin Select (PPS) flexibility (vs PIC32MX220F032D-I/TL)
- Compact 6x6 mm VTLA footprint with exposed thermal pad (vs PIC32MX220F032DT-I/PT (TQFP-44T))
Notas de projeto
USB design requires careful PCB layout. Route the D+ and D- traces as a 90-ohm differential pair with matched length, keeping maximum trace length under 50 mm. Place the 15 K pull-down resistor on D- close to the MCU. Use a common-mode choke on D+/D- if EMC compliance is required. Decouple VUSB with a 4.7 uF ceramic capacitor close to the VUSB pin (pin 22). The exposed thermal pad must be soldered to a copper pour connected to VSS for mechanical strength and electrical grounding; this is critical for thermal dissipation in industrial-temperature applications.
Place a 0.1 uF ceramic decoupling capacitor close to each VDD pin (pins 11 and AVDD pin 28) and a bulk 10 uF tantalum-capacitor on the VDD rail near the MCU. The internal 3.3 V LDO that powers USB requires adequate bulk capacitance on VUSB. Use a separate analog ground (AVSS) connected to the main VSS at a single point (star ground) to reduce ADC noise. For low-power Sleep mode designs, route unused I/O pins as outputs driven low to minimize current leakage. Power-on reset (POR) and Brown-Out Reset (BOR) thresholds should be configured via configuration words for reliable startup under varying supply ramp rates.
Common pitfalls include: (1) Mistaking the -TL suffix for a different pinout than -ML or other suffixes within the PIC32MX2xx family - the package suffix only denotes packaging format (Tape & Reel) or VTLA (6x6 mm) package, not the device variant. Verify the full part number carefully when substituting. (2) Forgetting to enable the JTAG/ICSP pins (PGEC1/PGED1 on pins 14/15) for programming access. (3) Failing to configure unused peripherals via DEVCFG registers, which can cause unwanted current draw. (4) Using ADC channels that share physical pins with VBUS/VUSB without proper isolation. Always consult the latest errata document (DS80000468M) before locking down a design.
Informações de conformidade
RoHS compliant per Microchip product declaration. Not AEC-Q100 qualified (industrial temperature grade only); not intended for automotive safety-critical applications. Halogen-free status should be confirmed via Microchip compliance portal. Conflict minerals compliant per Microchip supplier declarations.
