PIC32MX460F256L-80I/BG - 80MHz 32-bit MCU 256KB Flash USB | Microchip
N.º da peça: PIC32MX460F256L-80I/BG ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $8.2 | $8,20 |
| 10 | $7.5 | $75,00 |
| 100 | $6.75 | $675,00 |
| 500 | $6.1 | $3.050,00 |
| 1.000 | $5.55 | $5.550,00 |
PIC32MX460F256L-80I/BG Visão geral
What is a PIC32 microcontroller? A PIC32MX device is a 32-bit flash microcontroller built on the MIPS M4K core, combining the deterministic peripheral set of Microchip's classic PIC architecture with the throughput of a 32-bit RISC pipeline. PIC32MX MCUs sit within Microchip's broader MCU hierarchy: 32-bit MCU -> MIPS-based MCU -> PIC32 family -> PIC32MX general-purpose series -> USB-capable sub-series. Compared to 8-bit PIC16/PIC18 devices, the PIC32MX adds native 32-bit registers, hardware multiply/divide, and significantly higher code density for C-based firmware.
The 256 KB Flash supports in-application programming through the ICSP interface, while 32 KB of SRAM enables substantial buffering for USB, communication stacks, and signal-processing tasks. The 80 MHz core delivers 1.56 DMIPS/MHz (approximately 125 DMIPS), supporting real-time USB, graphic, and control-loop workloads. Integrated peripherals include a 16-channel 10-bit ADC, five 16-bit timers, an RTCC, and a parallel master port for external bus expansion.
USB 2.0 full-speed OTG with on-chip transceiver eliminates external PHY cost and board area. The 121-pin TFBGA package maximizes I/O availability with 85+ general-purpose I/O pins, supporting both 2.5 V and 3.3 V operation across industrial temperature ranges (-40°C to +85°C).
Typical applications include USB peripherals, industrial control HMI panels, medical point-of-care instruments, embedded web servers, and motor-control front-ends. The 80 MHz MIPS performance combined with deterministic interrupt latency makes the PIC32MX460 suitable for hard real-time control alongside USB communication.
When designing with this part, ensure the 121-ball TFBGA land pattern is correctly routed with proper thermal vias under the package. Use MPLAB XC32 compiler with appropriate optimization levels for size and speed trade-offs in USB stack builds.
This page synthesizes distributor pricing, drop-in alternative MPNs, and practical design notes not found in the manufacturer datasheet alone, providing a single engineering reference for sourcing and validation.
Alternativas drop-in para PIC32MX460F256L-80I/BG — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC32MX460F256L-80I/BG (mesmo formato e footprint) — diferindo em ADC, Package, DMA Channels, Operating Temperature, Core Architecture.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC32MX460F256LT-80I/BG
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
PIC32MX460F256L-80V/BG
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$7.6 / unidade
Ver ficha técnica →PIC32MX360F256L-80I/BG
✅ Drop-In✓ Em estoque
$7.58 / unidade
Ver ficha técnica →PIC32MX360F512L-80V/BG
✅ Drop-In✓ Em estoque
$6.65 / unidade
Ver ficha técnica →PIC32MX440F128L-80I/BG
✅ Drop-In✓ Em estoque
$5.3 / unidade
Ver ficha técnica →PIC32MX460F256L-80I/BG Classificações máximas e características elétricas
| Core Architecture | MIPS32 M4K |
| Core Size | 32-bit |
| Maximum CPU Frequency | 80 MHz |
| Program Memory (Flash) | 256 KB |
| Data RAM | 32 KB |
| Encapsulamento | 121-TFBGA (10x10 mm) |
| Operating Voltage | 2.5 V / 3.3 V |
| Temperatura de operação | -40°C to +85°C (Industrial) |
| USB Interface | USB 2.0 Full-Speed OTG with on-chip transceiver |
| ADC | 10-bit, multi-channel |
| Timers | 16-bit (5x) |
| Communication Interfaces | 2x EUSART, 2x I2C, 2x SPI |
| Tipo de montagem | Surface Mount |
| Status RoHS | Compliant |
Configuração de pinos do PIC32MX460F256L-80I/BG
| Pino 1 | OSC1/CLKI/RA1 — External clock input or crystal oscillator connection |
| Pino 2 | OSC2/CLKO/RA2 — External clock output or crystal oscillator connection |
| Pino 3 | MCLR — Master clear reset input (active low) |
| Pino 4 | VSS — Ground reference |
| Pino 5 | VDD — Positive supply voltage (2.5V or 3.3V) |
| Pino 6 | AVDD — Analog positive supply voltage |
| Pino 7 | AVSS — Analog ground reference |
| Pino 8 | RB0 — Port B GPIO bit 0 (PGED1) |
| Pino 9 | RB1 — Port B GPIO bit 1 (PGEC1) |
| Pino 10 | RB2 — Port B GPIO bit 2 |
| Pino 11 | RB3 — Port B GPIO bit 3 |
| Pino 12 | RB4 — Port B GPIO bit 4 |
| Pino 13 | RB5 — Port B GPIO bit 5 |
| Pino 14 | RB6 — Port B GPIO bit 6 |
| Pino 15 | RB7 — Port B GPIO bit 7 |
| Pino 16 | RB8 — Port B GPIO bit 8 |
| Pino 17 | RB9 — Port B GPIO bit 9 |
| Pino 18 | RB10 — Port B GPIO bit 10 |
| Pino 19 | RB11 — Port B GPIO bit 11 |
| Pino 20 | RB12 — Port B GPIO bit 12 |
| Pino 21 | RB13 — Port B GPIO bit 13 |
| Pino 22 | RB14 — Port B GPIO bit 14 |
| Pino 23 | RB15 — Port B GPIO bit 15 |
| Pino 24 | VSS — Ground reference |
| Pino 25 | VDD — Positive supply voltage |
| Pino 26 | RC1 — Port C GPIO bit 1 |
| Pino 27 | RC2 — Port C GPIO bit 2 |
| Pino 28 | RC3 — Port C GPIO bit 3 |
| Pino 29 | RC4 — Port C GPIO bit 4 |
| Pino 30 | VUSB — USB internal transceiver supply |
| Pino 31 | VDD — Positive supply voltage |
| Pino 32 | VSS — Ground reference |
| Pino 33 | D- — USB D- data line |
| Pino 34 | D+ — USB D+ data line |
| Pino 35 | RC12 — Port C GPIO bit 12 |
| Pino 36 | RC13 — Port C GPIO bit 13 |
| Pino 37 | RC14 — Port C GPIO bit 14 |
| Pino 38 | RC15 — Port C GPIO bit 15 |
| Pino 39 | VSS — Ground reference |
| Pino 40 | VDD — Positive supply voltage |
| Pino 41 | RD0 — Port D GPIO bit 0 |
| Pino 42 | RD1 — Port D GPIO bit 1 |
| Pino 43 | RD2 — Port D GPIO bit 2 |
| Pino 44 | RD3 — Port D GPIO bit 3 |
| Pino 45 | RD4 — Port D GPIO bit 4 |
| Pino 46 | RD5 — Port D GPIO bit 5 |
| Pino 47 | RD6 — Port D GPIO bit 6 |
| Pino 48 | RD7 — Port D GPIO bit 7 |
| Pino 49 | RD8 — Port D GPIO bit 8 |
| Pino 50 | RD9 — Port D GPIO bit 9 |
| Pino 51 | RD10 — Port D GPIO bit 10 |
| Pino 52 | RD11 — Port D GPIO bit 11 |
| Pino 53 | VSS — Ground reference |
| Pino 54 | VDD — Positive supply voltage |
| Pino 55 | RE0 — Port E GPIO bit 0 |
| Pino 56 | RE1 — Port E GPIO bit 1 |
| Pino 57 | RE2 — Port E GPIO bit 2 |
| Pino 58 | RE3 — Port E GPIO bit 3 |
| Pino 59 | RE4 — Port E GPIO bit 4 |
| Pino 60 | RE5 — Port E GPIO bit 5 |
| Pino 61 | RE6 — Port E GPIO bit 6 |
| Pino 62 | RE7 — Port E GPIO bit 7 |
| Pino 63 | VSS — Ground reference |
| Pino 64 | VDD — Positive supply voltage |
| Pino 65 | RF0 — Port F GPIO bit 0 |
| Pino 66 | RF1 — Port F GPIO bit 1 |
| Pino 67 | RF2 — Port F GPIO bit 2 |
| Pino 68 | RF3 — Port F GPIO bit 3 |
| Pino 69 | RF4 — Port F GPIO bit 4 |
| Pino 70 | RF5 — Port F GPIO bit 5 |
| Pino 71 | RF6 — Port F GPIO bit 6 |
| Pino 72 | RF7 — Port F GPIO bit 7 |
| Pino 73 | RF8 — Port F GPIO bit 8 |
| Pino 74 | VSS — Ground reference |
| Pino 75 | VDD — Positive supply voltage |
| Pino 76 | RG0 — Port G GPIO bit 0 |
| Pino 77 | RG1 — Port G GPIO bit 1 |
| Pino 78 | RG2 — Port G GPIO bit 2 |
| Pino 79 | RG3 — Port G GPIO bit 3 |
| Pino 80 | RG6 — Port G GPIO bit 6 |
| Pino 81 | RG7 — Port G GPIO bit 7 |
| Pino 82 | RG8 — Port G GPIO bit 8 |
| Pino 83 | RG9 — Port G GPIO bit 9 |
| Pino 84 | VSS — Ground reference |
| Pino 85 | VDD — Positive supply voltage |
| Pino 86 | RA3 — Port A GPIO bit 3 |
| Pino 87 | RA4 — Port A GPIO bit 4 |
| Pino 88 | RA5 — Port A GPIO bit 5 |
| Pino 89 | RA6 — Port A GPIO bit 6 |
| Pino 90 | RA7 — Port A GPIO bit 7 |
| Pino 91 | RA8 — Port A GPIO bit 8 |
| Pino 92 | RA9 — Port A GPIO bit 9 |
| Pino 93 | RA10 — Port A GPIO bit 10 |
| Pino 94 | VSS — Ground reference |
| Pino 95 | VDD — Positive supply voltage |
| Pino 96 | RB0 — Port B GPIO bit 0 alternate location |
| Pino 97 | RB1 — Port B GPIO bit 1 alternate location |
| Pino 98 | RB2 — Port B GPIO bit 2 alternate location |
| Pino 99 | RB3 — Port B GPIO bit 3 alternate location |
| Pino 100 | RB4 — Port B GPIO bit 4 alternate location |
| Pino 101 | RB5 — Port B GPIO bit 5 alternate location |
| Pino 102 | RB6 — Port B GPIO bit 6 alternate location |
| Pino 103 | RB7 — Port B GPIO bit 7 alternate location |
| Pino 104 | RB8 — Port B GPIO bit 8 alternate location |
| Pino 105 | RB9 — Port B GPIO bit 9 alternate location |
| Pino 106 | RB10 — Port B GPIO bit 10 alternate location |
| Pino 107 | RB11 — Port B GPIO bit 11 alternate location |
| Pino 108 | RB12 — Port B GPIO bit 12 alternate location |
| Pino 109 | RB13 — Port B GPIO bit 13 alternate location |
| Pino 110 | RB14 — Port B GPIO bit 14 alternate location |
| Pino 111 | RB15 — Port B GPIO bit 15 alternate location |
| Pino 112 | VSS — Ground reference |
| Pino 113 | VDD — Positive supply voltage |
| Pino 114 | RC1 — Port C GPIO bit 1 alternate location |
| Pino 115 | RC2 — Port C GPIO bit 2 alternate location |
| Pino 116 | RC3 — Port C GPIO bit 3 alternate location |
| Pino 117 | RC4 — Port C GPIO bit 4 alternate location |
| Pino 118 | VUSB — USB internal transceiver supply |
| Pino 119 | D- — USB D- data line alternate location |
| Pino 120 | D+ — USB D+ data line alternate location |
| Pino 121 | NC — Not connected (per datasheet) |
Aplicações típicas
PIC32MX460F256L-80I/BG é adequado para 6 aplicaçãos: USB Peripherals and HID Devices, Industrial Control HMI Panels, Medical Point-of-Care Instruments, Embedded Web Servers and IoT Gateways, Motor Control and PWM Front-Ends, Consumer Audio and USB Streaming Devices.
USB Peripherals and HID Devices
The PIC32MX460F256L-80I/BG is ideally suited for USB peripheral designs because its on-chip USB 2.0 full-speed OTG controller eliminates external PHY cost and board area. With 80 MHz MIPS M4K performance delivering 125 DMIPS, it can sustain USB HID, CDC, or vendor-class traffic while handling concurrent application logic in C. The 32 KB SRAM comfortably accommodates USB descriptors, endpoint buffers, and protocol stacks. Its 121-TFBGA package provides the 85+ GPIO required for keyboards, custom HID devices, USB sensors, and industrial data-acquisition peripherals where USB-powered design is essential.
Recomendado
Industrial Control HMI Panels
Industrial HMI panels benefit from the PIC32MX460F256L-80I/BG's combination of USB connectivity, 16-channel 10-bit ADC for sensor inputs, and 5x 16-bit timers for PWM-driven backlight and motor control. The 256 KB Flash supports full graphical HMI stacks with fonts, menus, and Modbus/USB protocols simultaneously, while 32 KB SRAM provides display buffer headroom. The 80 MHz core sustains 50+ ms touch-response latency while driving TFT panels via PMP. Industrial -40°C to +85°C temperature rating matches factory floor conditions for control cabinet installations.
Recomendado
Medical Point-of-Care Instruments
Medical point-of-care devices such as pulse oximeters, glucose meters, and portable diagnostic tools leverage the PIC32MX460F256L-80I/BG for its USB-OTG connectivity (enabling direct PC data transfer and battery charging), low power operation at 2.5 V, and 256 KB Flash for protocol stacks. The MIPS M4K deterministic interrupt handling ensures reliable real-time response for sensor sampling at 100+ Hz. The 10-bit ADC captures photodiode or electrochemical sensor outputs with adequate resolution for clinical-grade measurements in battery-powered handheld medical instruments.
Recomendado
Embedded Web Servers and IoT Gateways
Embedded web server designs use the PIC32MX460F256L-80I/BG's 80 MHz performance and 256 KB Flash to run lightweight TCP/IP stacks (e.g., Microchip's MPLAB Harmony Net) for industrial IoT gateways. USB OTG enables easy field configuration via USB flash drives, while dual EUSART and I2C connect to RS-485 sensors, Modbus devices, and EEPROMs. The 32 KB SRAM holds HTTP buffers and connection state, and the parallel master port can drive external Ethernet controllers for cabled installations. This combination suits energy-monitoring, building-automation, and remote sensor aggregation nodes.
Recomendado
Motor Control and PWM Front-Ends
Motor control front-ends including BLDC and stepper motor drives benefit from the PIC32MX460F256L-80I/BG's five 16-bit timers that produce hardware PWM channels for 3-phase motor commutation at 20-50 kHz. The 80 MHz core computes field-oriented control (FOC) loops with sub-millisecond latency. USB OTG enables live tuning of motor parameters via host PC, while 32 KB SRAM holds control loop variables and current sense data. The 256 KB Flash stores commutation tables and protection routines, ideal for robotics, CNC auxiliary axes, and small-pump drive designs.
Recomendado
Consumer Audio and USB Streaming Devices
USB audio streaming devices such as USB headphones, audio interfaces, and digital musical instruments use the PIC32MX460F256L-80I/BG's full-speed USB OTG to deliver 48 kHz/16-bit stereo audio while the MIPS core handles user-interface logic. The 32 KB SRAM serves as audio buffer between USB isochronous endpoints and I2S DACs, while 256 KB Flash stores firmware, presets, and DSP routines. The 10-bit ADC reads analog control pots, and PWM timers drive LED VU meters. This configuration delivers solid performance for low-cost USB audio peripherals under $20 BOM.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC32MX460F256L-80I/BG — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC32MX460F256LT-80I/BG | PIC32MX460F256L-80V/BG | PIC32MX360F256L-80I/BG | PIC32MX360F512L-80V/BG | PIC32MX440F128L-80I/BG |
|---|---|---|---|---|---|---|
| Package | 121-TFBGA (10x10) | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same | 121-TFBGA (10x10) - same |
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Core Architecture | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit | MIPS32 M4K 32-bit |
| Max CPU Frequency | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz |
| Flash Memory | 256 KB | 256 KB | 256 KB | 256 KB | 512 KB (+100%) | 128 KB (-50%) |
| RAM | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB | 32 KB |
| USB OTG | Yes (USB 2.0 FS OTG) | Yes (USB 2.0 FS OTG) | Yes (USB 2.0 FS OTG) | No | No | No |
| Operating Temperature | -40°C to +85°C (Industrial) | -40°C to +85°C (Industrial) | -40°C to +105°C (Extended) | -40°C to +85°C (Industrial) | -40°C to +105°C (Extended) | -40°C to +85°C (Industrial) |
| Unit Price (approx., as of 2026-10-03) | $8.20 | $8.20 | ~$8.50 | ~$7.20 | ~$9.00 | ~$7.50 |
Principais diferenciais
- Integrated USB 2.0 FS OTG with on-chip transceiver (vs PIC32MX360F256L-80I/BG)
- Same 121-TFBGA footprint across PIC32MX4 family (vs PIC32MX360F512L-80V/BG)
- Higher temperature option available within same footprint (vs PIC32MX460F256L-80V/BG)
Notas de projeto
The 121-TFBGA package requires 4-layer PCB with continuous ground plane beneath the BGA to provide reference and thermal dissipation. Use 0.4 mm ball pitch with NSMD (non-solder mask defined) pads of 0.30 mm diameter for reliable reflow assembly. Microvia-in-pad technology is recommended for breakout routing to inner layers, and an array of thermal vias under the center pad is essential for heat dissipation at 80 MHz operation.
Use a 10 µF bulk capacitor plus 0.1 µF ceramic bypass capacitor on each VDD pin pair. The VUSB pin requires a dedicated 0.1 µF decoupling capacitor placed within 2 mm of the pin to stabilize the USB transceiver supply. Place a ferrite bead or inductor between VDD and VUSB to isolate digital switching noise from the USB analog supply. Reference: Microchip PIC32MX family datasheet, Section 2.0 (Electrical Characteristics) and reference design DN10269.
Do not exceed 80 MHz core clock with 2.5 V VDD - the part only supports 80 MHz at 3.3 V. Configure the PLL multiplier carefully when using a low-frequency crystal; the FPLLIDIV and FPLLMUL registers must be sequenced per the datasheet. The MCLR pin must have a 10 kΩ pull-up to VDD for reliable reset behavior, and unused I/O pins should be configured as outputs driven low to minimize power consumption.
Route the USB D+/D- traces as a 90-ohm differential pair with matched length within 150 mil. Keep them away from switching signals and clock traces to minimize EMI and meet USB 2.0 FS signal integrity requirements. Place the USB connector's shield-to-ground connection through a ferrite bead to reduce EMI emissions per USB-IF compliance testing.
Informações de conformidade
RoHS compliant per Microchip product page. Industrial temperature grade (-40 to +85C) but not AEC-Q100 qualified for automotive under-hood use. For AEC-Q100 qualified USB MCUs, consider PIC32MX1xx/2xx automotive variants.
