PIC32MX795F512L-80I/PT - 80MHz MIPS MCU 512KB Flash USB/Ethernet/CAN | Microchip
N.º da peça: PIC32MX795F512L-80I/PT ✓ Ativo| Qtd. | Preço unitário | Total |
|---|---|---|
| 1 | $11.2 | $11,20 |
| 10 | $10.05 | $100,50 |
| 100 | $8.95 | $895,00 |
| 500 | $8.2 | $4.100,00 |
| 1.000 | $7.55 | $7.550,00 |
PIC32MX795F512L-80I/PT Visão geral
A 32-bit microcontroller (MCU) is a programmable logic device that executes instructions from on-chip Flash memory, providing significantly higher throughput than 8-bit or 16-bit MCUs while integrating peripherals (timers, ADC, communication controllers) and memory on a single die. In the broader taxonomy, the PIC32MX family sits under Microchip's PIC32 (PIC) umbrella as a MIPS-based high-performance line aimed at embedded connectivity, bridging the gap between legacy PIC16/PIC24 devices and the higher-end PIC32MZ ARM-class portfolio. The '795' designator indicates the premium feature set: full USB OTG, Ethernet MAC, dual CAN, and maximum Flash/RAM density within the MX5/MX6/MX7 family.
Key features include 8 dedicated DMA channels for peripheral offload, a 5-stage Harvard pipeline, 16-channel 10-bit ADC at 1 MSps, five 16-bit timers/counters, two comparators, two I2C, two SPI, and up to six UART interfaces. The integrated USB OTG PHY eliminates external PHY components, while the Ethernet MAC supports both MII and RMII for PHY flexibility. The 100-pin TQFP package has mature PCB layout libraries available from Microchip and third parties.
Architecturally, the device uses a Harvard memory architecture with separate instruction and data buses, hardware multiply/divide, and a prefetch cache to sustain throughput. The 8-channel dedicated DMA engine enables zero-CPU-overhead data movement between peripherals and RAM, critical for high-bandwidth Ethernet and USB stacks. The peripheral bus matrix allows concurrent DMA-driven traffic on USB, Ethernet, and CAN while the core executes user tasks, supporting deterministic multi-protocol industrial buses.
Typical applications include industrial Ethernet gateways, CAN-based automotive body controllers, USB-OTG device/host peripherals, embedded web servers, and PIC32 Bluetooth/USB bridging. The part is also a fit for PLC communication modules and Ethernet/IP nodes where deterministic connectivity matters.
When designing with this part, ensure decoupling follows Microchip's 100-pin TQFP reference design (typically 100 nF + 10 uF bulk on each VDD rail), reserve an ICSP header for MPLAB ICD programming, and verify that the chosen Ethernet PHY's MII/RMII voltage matches the MCU's 3.3V I/O.
This page synthesizes distributor pricing, drop-in alternatives drawn from the same PIC32MX7xx family (same 100-pin TQFP footprint), and practical design notes not found in the manufacturer datasheet, giving engineers a faster path to a working BOM.
Alternativas drop-in para PIC32MX795F512L-80I/PT — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
Variantes desta série
Modelos da mesma série compatíveis como drop-in com PIC32MX795F512L-80I/PT (mesmo formato e footprint) — diferindo em ADC, Package, USB, DMA Channels, Operating Temperature.
Ferramenta de comparação rápida — selecione peças alternativas para comparação lado a lado:
PIC32MX675F512L-80I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$5.42 / unidade
Ver ficha técnica →PIC32MX575F512H-80I/MR
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$6.72 / unidade
Ver ficha técnica →PIC32MX795F512LT-80I/PT
✅ Drop-In✓ Em estoque
$6.53 / unidade
Ver ficha técnica →PIC32MX795F512L-80I/PF
✅ Drop-In✓ Em estoque
$9.95 / unidade
Ver ficha técnica →PIC32MX550F256L-I/PT
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$3.78 / unidade
Ver ficha técnica →PIC32MX270F512L-50I/PF
✅ Drop-In ⚠️ Especificações não verificadas✓ Em estoque
$5.2 / unidade
Ver ficha técnica →PIC32MX795F512L-80I/PT Classificações máximas e características elétricas
| Core Architecture | MIPS32 M4K (32-bit RISC) |
| Core Pipeline | 5-stage Harvard |
| Maximum CPU Clock | 80 MHz (105 DMIPS) |
| Program Memory (Flash) | 512 KB |
| Data Memory (SRAM) | 128 KB |
| Supply Voltage (VDD) | 2.3 V to 3.6 V |
| GPIO Pins | 85 (5V tolerant inputs) |
| USB Controller | USB 2.0 OTG with integrated PHY |
| Ethernet MAC | 10/100 Mbps, MII/RMII |
| CAN Controllers | 2 x CAN 2.0b |
| DMA Channels | 8 dedicated |
| ADC | 10-bit, 16 channels, up to 1 MSps |
| Timers | 5 x 16-bit |
| UART/SPI/I2C | up to 6 UART, 4 SPI, 5 I2C |
| Comparators | 2 |
| Temperatura de operação | -40C to +85C (Industrial) |
| Encapsulamento | 100-pin TQFP (PT), 12x12 mm |
| Tipo de montagem | Surface Mount |
| Nível MSL | 3 (per JEDEC J-STD-020) |
| Status RoHS | Compliant |
Guia de Configuração de Pinos do PIC32MX795F512L-80I/PT 100-pin tqfp (pt), 12x12 mm
Configuração de pinos para PIC32MX795F512L-80I/PT (pacote 100-pin tqfp (pt), 12x12 mm). Este CI digital inclui GPIO, interfaces de comunicação (UART, SPI, I2C) e pinos de alimentação. Consulte o datasheet do fabricante para funções alternativas dos pinos e opções de configuração. Essencial para projeto de sistemas embarcados e layout de PCB.
Nenhum dado detalhado de pinagem disponível para PIC32MX795F512L-80I/PT.
Consulte a ficha técnica para a configuração completa dos pinos.
Aplicações típicas
PIC32MX795F512L-80I/PT é adequado para 7 aplicaçãos: Industrial Ethernet Gateway, CAN-based Automotive Body Controller, USB-OTG Device/Host Peripheral, Embedded Web Server / IoT Edge Node, PIC32MX to Bluetooth/USB Bridge, PLC Communication Module (EtherNet/IP / Modbus), Industrial Data Acquisition Logger.
Industrial Ethernet Gateway
The PIC32MX795F512L-80I/PT suits industrial Ethernet gateways because it integrates a 10/100 Ethernet MAC with MII/RMII interface alongside dual CAN 2.0b controllers. The 80 MHz MIPS32 M4K core delivers 105 DMIPS, enough to run lwIP TCP/IP stacks and HTTP servers concurrently while the 8 dedicated DMA channels keep packet movement off the CPU. The 512 KB Flash holds a full web management interface and TLS 1.2 client, while the 128 KB SRAM sustains TCP socket buffers. Industrial -40C to +85C operation covers factory floor ambient temperatures without derating. The 100-pin TQFP package provides 85 GPIO pins for status LEDs, button inputs, and external sensor interfaces.
Recomendado
CAN-based Automotive Body Controller
The PIC32MX795F512L-80I/PT integrates dual CAN 2.0b controllers suitable for body-control modules, gateway nodes, and gateway ECU bridges. The 512 KB Flash hosts a CANopen or J1939 stack with diagnostic handlers, while the 8 DMA channels handle message buffering without CPU overload. Operating at 80 MHz, the core arbitrates multiple CAN buses while simultaneously driving an LCD or driving external peripherals via UART/SPI. The -I industrial temperature grade covers most cabin-mounted automotive ECUs. The 100-pin TQFP package supports through-hole-friendly reflow manufacturing for production lines.
Recomendado
USB-OTG Device/Host Peripheral
The PIC32MX795F512L-80I/PT integrates USB 2.0 OTG with on-chip PHY, eliminating external PHY cost and PCB area. Engineer can deploy mass-storage, CDC, HID, or vendor-class device firmware, or configure the same MCU as USB host reading thumb drives, keyboards, or printers. With 512 KB Flash and 128 KB SRAM, the part holds a full USB stack plus application-level protocols. The 80 MHz core sustains 12 Mbps USB throughput while running application tasks. Compared to off-chip-PHY alternatives, the integrated PHY reduces BOM cost by $1.50-$2.50 in production volumes.
Recomendado
Embedded Web Server / IoT Edge Node
The PIC32MX795F512L-80I/PT runs embedded HTTP/HTTPS servers with the lwIP TCP/IP stack and Microchip's MPLAB Harmony v3 framework. The 512 KB Flash accommodates the HTTP server, JSON parsing library, and TLS client handshake code. The Ethernet MAC integrates seamlessly with the same DMA engine, handling packet buffers at line rate without CPU stalls. The dual CAN interfaces let the same board act as an IoT bridge between factory CAN networks and Ethernet uplinks. Industrial -40C to +85C operation matches unattended edge cabinets where active cooling is impractical.
Recomendado
PIC32MX to Bluetooth/USB Bridge
The PIC32MX795F512L-80I/PT acts as a bridging controller between legacy UART-only Bluetooth modules and USB hosts, thanks to its six UART interfaces plus USB OTG. Designers can develop products where a legacy Bluetooth modem communicates with a host PC via a virtual COM port implemented on the PIC32. The 80 MHz core performs baud-rate translation and protocol handling, with 128 KB SRAM holding ingress/egress buffers. The integrated USB PHY and dual CAN interfaces make this part a multi-protocol bridge suitable for industrial M2M gateways.
Recomendado
PLC Communication Module (EtherNet/IP / Modbus)
The PIC32MX795F512L-80I/PT handles EtherNet/IP and Modbus TCP master/slave protocols concurrently with 80 MHz core throughput, making it suitable for slave modules on industrial PLC backplanes. The 100-pin TQFP provides GPIO for digital I/O expansion and LED indication, while the Ethernet MAC and dual CAN serve as the protocol front-end. Microchip provides EtherNet/IP stack libraries under MPLAB Harmony v3 with verified conformance. Operating temperature -40C to +85C supports cabinet-mounted PLC environments without additional thermal management.
Recomendado
Industrial Data Acquisition Logger
The PIC32MX795F512L-80I/PT fits data-acquisition loggers because it combines a 16-channel 10-bit ADC at 1 MSps with USB OTG and Ethernet MAC, allowing local storage then upload to a host. The 128 KB SRAM buffers sample bursts while the Ethernet or USB handles data offload without missed samples. The 8 DMA channels handle ADC bursts and bus transfers concurrently. Industrial -40C to +85C operation lets the logger operate inside enclosures near machinery without overheating shutdown.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para PIC32MX795F512L-80I/PT — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | PIC32MX675F512L-80I/PT | PIC32MX575F512H-80I/MR | PIC32MX795F512LT-80I/PT | PIC32MX795F512L-80I/PF | PIC32MX550F256L-I/PT | PIC32MX270F512L-50I/PF |
|---|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 100-pin TQFP (PT) | 100-pin TQFP (PT) - same | 100-pin QFN (MR) | 100-pin TQFP (PT) - same | 100-pin TQFP (PF) - same footprint | 100-pin TQFP (PT) - same | 100-pin TQFP (PF) - same footprint |
| Core Architecture | MIPS32 M4K, 32-bit | MIPS32 M4K, 32-bit | MIPS32 M4K, 32-bit | MIPS32 M4K, 32-bit | MIPS32 M4K, 32-bit | MIPS32 M4K, 32-bit | MIPS32, 40MHz core |
| Max Clock Speed | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 80 MHz | 50 MHz (-37.5%) |
| Program Flash | 512 KB | 512 KB | 512 KB | 512 KB | 512 KB | 256 KB (-50%) | 512 KB |
| SRAM | 128 KB | 128 KB | 64 KB (-50%) | 128 KB | 128 KB | 32 KB (-75%) | 64 KB (-50%) |
| USB Controller | USB 2.0 OTG with integrated PHY | USB 2.0 OTG with integrated PHY | USB Device only (no OTG) | USB 2.0 OTG with integrated PHY | USB 2.0 OTG with integrated PHY | USB Device only | USB Device only |
| Ethernet MAC | 10/100 Ethernet MII/RMII | None (CAN + USB only) | None | 10/100 Ethernet MII/RMII | 10/100 Ethernet MII/RMII | None | None |
| CAN Controllers | 2 x CAN 2.0b | 2 x CAN 2.0b | 1 x CAN 2.0b | 2 x CAN 2.0b | 2 x CAN 2.0b | None | None |
| DMA Channels | 8 dedicated | 8 dedicated | 8 dedicated | 8 dedicated | 8 dedicated | 8 dedicated | None |
| Operating Temperature | -40C to +85C (Industrial) | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C | -40C to +85C |
Principais diferenciais
- Integrated USB-OTG with PHY and full 10/100 Ethernet MAC plus dual CAN on one die (vs PIC32MX575F512H-80I/MR)
- Highest-density SRAM in PIC32MX5/6/7 family (128 KB) for protocol buffers (vs PIC32MX550F256L-I/PT)
- Industrial -40C to +85C qualification with full feature set (vs PIC32MX470F512L-V/PF)
Notas de projeto
Estimated: at 80 MHz with all peripherals active, the PIC32MX795F512L draws up to 100 mA from the 2.3-3.6V supply. Place a 10 uF bulk tantalum plus a 100 nF ceramic decoupling capacitor within 2 mm of each VDD/VSS pin pair. The USB PHY requires its own filtered 3.3V rail (USB VBUS-to-VUSB) when operating in host mode to limit digital-noise coupling.
The 100-pin TQFP package requires 4-layer PCB routing for signal integrity above 50 MHz core speeds. Keep RMII traces to the Ethernet PHY matched within 2 mm and length-matched within 0.5 cm. Place the 25 MHz main oscillator crystal within 5 mm of the OSC1/OSC2 pins with a guarded ground pour per Microchip 100-pin TQFP reference design guidelines.
Do not enable USB OTG host-mode VBUS drive before asserting appropriate overcurrent protection. The dual CAN controllers require 120 ohm termination resistors at the bus ends, not on the module. Always verify the JTAG/ICSP pinout matches the Microchip ICD programming header before fabout - the MCLR pin is a 5V-tolerant input that may need a 10 kohm pull-up for stable reset.
Estimated: at continuous 80 MHz core operation, the silicon junction-to-ambient thermal resistance is approximately 40 C/W in the 100-pin TQFP package. For ambient-temperature designs above 60C, ensure 1-2 square inches of copper pour beneath the exposed pad. No external heatsink is required in industrial -40C to +85C operation under normal load profiles per Microchip thermal models.
Informações de conformidade
RoHS and REACH compliant per Microchip product page. AEC-Q100 qualification not applicable for industrial-grade MCUs in non-safety-critical applications. Halogen-free status not confirmed in provided data - flagged as unknown.
