SN74HC368D - 6-Channel 3-State Inverting Buffer | Texas Instruments
N.º da peça: SN74HC368D ✓ AtivoSN74HC368D Visão geral
A 74HC-series logic buffer is a digital bus-interface component that strengthens signal levels, isolates a source from downstream loads, and provides controlled connection to shared buses. The SN74HC368 belongs to the broader CMOS logic hierarchy and is intended for systems that require higher drive capability or reduced loading without adding another active protocol level. Its inverting outputs support clock and data paths where inversion is acceptable or intentional.
The main features include six inverting channels, individual 3-state output control, operation from 2 V to 6 V, and low-power CMOS design. The active-low enable inputs place the associated output channels in a high-impedance state when disabled, allowing multiple devices to share a bus without actively driving conflicting logic levels. This architecture is useful for memory address drivers, clock distribution, bus-oriented transmitters, and control-signal isolation.
The two output groups are organized as dual four-line and two-line buffers. Their enable inputs are labeled 1OE and 2OE, permitting two independently enabled bus segments on one package. When an enable input is low, the associated outputs pass inverted input data; when it is high, the relevant outputs enter the high-impedance state. This grouping provides more flexibility than a single shared control while retaining a compact 16-pin footprint.
Typical uses include driving clock lines, translating between lightly loaded bus nodes and higher-capacitance board traces, and connecting several subcircuits to shared data buses. The 3-state outputs are particularly suitable for systems in which peripheral devices must be disconnected during inactive periods. Logic compatibility and timing should be checked against the connected HC-family devices, and output-enable transitions should remain synchronized with the signals being disabled.
For robust board-level use, place the device close to the driven bus, minimize trace length on high-speed clock paths, and maintain a continuous ground reference. Decoupling capacitors should be placed directly between VCC and GND, with the power and ground pins connected to low-impedance planes. Avoid using the 3-state outputs as a substitute for proper bus turnaround or direction-control logic.
This page combines the functional description, package and pin information, drop-in replacement analysis, comparison data, and practical interface-design guidance. It is intended to help engineers identify the correct 74HC-family buffer for shared-bus, clock-driving, and inverting-interface designs before finalizing a PCB layout or production BOM.
Alternativas drop-in para SN74HC368D — mesmo encapsulamento, compatível pino a pino. Peças de encapsulamento diferente que exigem retrabalho na PCB são excluídas.
CD74HC368M
✅ Drop-In ⚠️ Especificações não verificadas📋 Alternativa de referência (fora do catálogo)
74HC368D,653
✅ Drop-In📋 Alternativa de referência (fora do catálogo)
SN74HC368D Classificações máximas e características elétricas
| Number of Channels | 6 channels |
| Logic Type | Hex inverting buffer and line driver |
| Configuração de saída | 6-channel 3-state output |
| Organização da memória | Dual 4-line and 2-line |
| Supply Voltage Range | 2 V to 6 V |
| Output Enable Polarity | Active low |
| Number of Output Enable Inputs | 2 independent inputs |
| Encapsulamento | 16-pin SOIC |
| Tipo de montagem | Surface mount |
| Faixa de temperatura de operação | -40 °C to +85 °C |
| Logic Level | HC-series CMOS |
Configuração de pinos do SN74HC368D
| Pino 1 | 1A1 — Input for output 1Y1 |
| Pino 2 | 1A2 — Input for output 1Y2 |
| Pino 3 | 1A3 — Input for output 1Y3 |
| Pino 4 | 1A4 — Input for output 1Y4 |
| Pino 5 | 1OE — Active-low output enable for the four-line section |
| Pino 6 | 2A1 — Input for output 2Y1 |
| Pino 7 | 2A2 — Input for output 2Y2 |
| Pino 8 | GND — Ground reference |
| Pino 9 | 2A3 — Input for output 2Y3 |
| Pino 10 | 2A4 — Input for output 2Y4 |
| Pino 11 | 2OE — Active-low output enable for the two-line section |
| Pino 12 | 1Y1 — Inverted 3-state output 1 |
| Pino 13 | 1Y2 — Inverted 3-state output 2 |
| Pino 14 | 1Y3 — Inverted 3-state output 3 |
| Pino 15 | 1Y4 — Inverted 3-state output 4 |
| Pino 16 | VCC — Power supply |
Aplicações típicas
SN74HC368D é adequado para 6 aplicaçãos: Shared Data-Bus Interface, Clock Distribution, Memory Address Driving, Peripheral Bus Isolation, Industrial Control Signal Routing, Test and Measurement Interface.
Shared Data-Bus Interface
The SN74HC368D is useful in a shared data-bus arrangement where multiple logic sections must connect and disconnect from the same node. Its six inverting channels are divided into a four-line group and a two-line group, each controlled by a separate active-low enable input. When an enable input is high, the associated outputs become high impedance and stop contributing to the bus node. When it is low, the section drives the inverted input signals with additional buffering. This arrangement reduces contention when several subcircuits share a trace, provided enable timing is coordinated with the receiving logic and the connected devices use compatible 74HC signal levels.
Recomendado
Clock Distribution
The SN74HC368D can distribute an inverted clock when the receiving logic can accommodate the inversion and the required edge rate. Each of its four-line and two-line sections has an independent active-low output enable, allowing clock drive to one portion of a board while another portion remains isolated. The 2 V to 6 V operating range supports standard 74HC-family rails, while the buffer function helps reduce source loading when driving multiple clock inputs. Timing checks should include clock rise and fall time, propagation delay, capacitive loading, and any downstream requirement for a non-inverted clock waveform.
Recomendado
Memory Address Driving
The SN74HC368D is applicable to memory-interface routing where address or control signals must drive a lightly loaded board segment and then be disconnected from a shared line. Its 3-state outputs prevent the buffer from holding the bus when another address source needs control. The six available channels can be allocated across address, chip-select, or read-control paths, subject to the datasheet's four-line and two-line grouping. Because the outputs invert their inputs, the system logic must account for that polarity and maintain valid setup and hold timing at the destination device.
Recomendado
Peripheral Bus Isolation
The SN74HC368D can isolate a peripheral interface from a shared system bus by placing its output section in the high-impedance state during periods when the peripheral does not own the bus. The four-line and two-line organization allows the design to assign related data and control signals to independently enabled groups. The inversion must be included in the interface logic, and enable inputs should not change while a receiving device is sampling an active transition. This approach is most appropriate for 74HC-compatible systems that need simple buffered isolation rather than direction-controlled, level-translating bus transceivers.
Recomendado
Industrial Control Signal Routing
The SN74HC368D fits control boards that distribute active-low or inverted control signals across multiple logic blocks while selectively disconnecting outputs from shared wiring. Its separate enable controls let a controller prevent simultaneous drive from two sections, and the 2 V to 6 V supply range accommodates common 74HC logic rails. For industrial equipment, the exact temperature grade and qualification status should be checked against the environmental requirements. Layout should also account for ground bounce and supply transients so that a disabled buffer does not introduce unwanted current into the control node.
Recomendado
Test and Measurement Interface
The SN74HC368D can buffer control signals in test and measurement equipment where a central controller must connect to a line driver, memory device, or logic card through a shared backplane. Its six 3-state channels provide selectable participation in the bus, while the inverted output behavior is predictable and easy to include in stimulus timing. The package supports compact surface-mount implementation, but signal-integrity checks remain important because long backplane traces can add capacitance and reflections. Keep enable paths short, use controlled-impedance routing where appropriate, and verify timing with the highest expected loading condition.
Recomendado
Resumo dos produtos recomendados
Dados de referência de engenharia para SN74HC368D — comparação, orientação de projeto e informações de conformidade.
Guia de seleção
Comparação com alternativas
| Parâmetro | Este produto | CD74HC368M | 74HC368D,653 |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Nexperia USA Inc. |
| Package | 16-SOIC | 16-SOIC - same | 16-SOIC - same |
| Number of Channels | 6 channels | 6 channels | 6 channels |
| Logic Function | Hex inverting buffer and line driver | Hex inverting buffer and line driver | Hex inverting buffer and line driver |
| Output State | 3-state | 3-state | 3-state |
| Supply Voltage Range | 2 V to 6 V | 2 V to 6 V | 2 V to 6 V |
| Output Enable | Dual active-low output enable | Dual active-low output enable | Dual active-low output enable |
| Channel Organization | Dual 4-line and 2-line | Dual 4-line and 2-line | Dual 4-line and 2-line |
| Mounting Type | Surface mount | Surface mount | Surface mount |
Principais diferenciais
- Two independently controlled output groups (vs 74HC368D,653)
- Pin-compatible multi-source sourcing (vs CD74HC368M)
- Shared 74HC bus interface (vs 74HC368D,653)
Notas de projeto
Route the two active-low output-enable inputs as control signals with attention to their relationship to the data being disabled. When a group enters the high-impedance state, its associated outputs should not change state while the receiving device is sampling. Place the device close to the driven bus when clock or data timing is critical, and keep the ground-return path continuous to limit output switching noise.
Place the local VCC bypass capacitor directly between the VCC and GND pins, with the shortest possible ground connection. Follow the recommended capacitor value and placement in the manufacturer datasheet. Keep the supply and return paths away from noisy switching nodes, and verify that the power rail remains within the device's 2 V to 6 V operating range during startup, load changes, and supply disturbances.
Treat every enabled output as a digital signal source and check both edge rate and loading at the destination. Long PCB traces, connectors, and cable capacitance can slow transitions enough to cause timing failures even when the destination device has a nominal propagation-delay rating. Use the datasheet's recommended input transition-time limits and simulate or measure the worst-case connected load before release.
Do not confuse a disabled high-impedance output with a driven logic-low output. A high-impedance channel does not establish a valid low level and may require a pull-up or pull-down elsewhere on the bus. Also account for the inversion of every output: a low input produces a high enabled output. Verify enable polarity, logical inversion, and system reset behavior together to prevent unintended bus contention.
Informações de conformidade
Environmental and qualification declarations must be confirmed for the exact manufacturer order code and current production status.